Super Vision at Ultra Low Light SHC-745 User Guide
Contents
1. COMM ADJ Communication Adjustment This function sets up the camera communication COMMUNICATION SETUP status when controlling the camera through an i external control device Press SET to Return When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates COMM ADJ Set up the mode using the 4 direction buttons CAM ID Determines the camera s identification number between 0 and 255 BAUD RATE You can select 2400 4800 9600 19200 38400 57600 bps UART MODE You can select NONE EVEN or ODD for the parity bits RET PKT Determines whether to send a command back to the controller device when a communication control command is sent to the camera DISP CAM ID Display camera title on top left corner of the screen O LANGUAGE You can select the menu language according to your requirements RESET Resets the camera settings to the factory defaults Communication status and language is not initialized RETURN Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu EXIT Press the SET button in the EXIT menu to save the current settings and exit the MAIN SETUP menu COLOR CCD CAMERA 35 User Guide Troubleshooting If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Nothing appears on the screen gt Check2. COM1 Serial Cable RS 485 Converter Camera RS 485 Control Port ANY 4 CONNECTION TERMINAL TRX CONNECTION TERMINAL TRX RS 485 Communication establishment initial value Camera ID BAUD RATE UART MODE PET PKT As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 AC 24V 10 There may be some deviation in voltage drop depending on the type of wire and the manufacturer 1 9600 8 NONE 1 ENABLE e To control the camera by constructing an additional controller use Pelco D protocol or STW protocol Samsung Techwin protocol LENS SHADE DC VIDEO MANUAL EXPOSURE SHUTTER RETURN AGC SENS UP WHITE BALANCE ATW OUTDOOR MANUAL INDOOR AWC SET BACKLIGHT OFF BLC SSNR ON OFF DAY NIGHT COLOR EXTERN B W IMAGE ADJUSTMENT IMAGE ADJ V REV SHARPNESS H REV RETURN D ZOOM SPECIAL CAMTITLE PRIVACY LANGUAGE SYNC DIS RESET MOTION DET COMM ADJ RETURN You can set up functions using the 5 buttons on the rear of the camera UP button SET button LEFT button DOWN button RIGHT button 1 Press
3. The HLC is not activated in light or overly dark conditions COLOR CCD CAMERA 25 User Guide This function reduces the background noise in a low luminance environment 1 When the SETUP menu screen is displayed select SSNR by using the Up and Down buttons so that the arrow indicates SSNR P 5 55HE a 2 Select a desired mode using the Left and Right buttons OFF Deactivates SSNR Noise is not reduced ON Activates SSNR so that noise is reduced 3 Set the SSNR mode to ON and press the SET button Then you can adjust the noise reduction level Press SET to Return You cannot set the SSNR to ON or OFF when the AGC mode of the EXPOSURE menu is OFF e When adjusting the noise reduction level of the SSNR mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur You can display pictures in color or black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Up and Down buttons so that the arrow indicates DAY NIGHT P 5 DRY HIGHT AUTO 2 Select a desired mode using the Left and Right buttons according to the picture display you want O COLOR The picture is always displayed in color O BIW The picture is always displayed in black and white AUTO The mode is switched to Color in a normal environment but switches to B W mode when ambient illumination Rowen T
4. 0 to 359 when select phase e You can decide the synchronization between luminance and color signal when select the Mode to TRACE COLOR CCD CAMERA 32 User Guide Notes J How to Use the Camera e When using AC power at 60Hz frequency you can use the L L type synchronization e When the power is DC 12V the SYNC menu is fixed to the INT mode MOTION DET If you connect an alarm device to this camera MOTION DET you can monitor activity more efficiently because a signal is generated by the camera whenever motion is detected The motion detection signal is output through the MD OUT port When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates MOTION DET Set up the mode using the 4 direction buttons SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even small movement AREA MODE Determines whether to use the MD area selected in SENSITIVITY SEL POS Determines which of the 4 vertices of each MD area is to be used YPOS Determines the coordinate of the vertical axis for SEL POS XPOS Determines the coordinate of the horizontal axis for SEL POS FILL SET Fills in a selected MD area Fills in a selected MD area The color of filling is sequentially selected as brown orange blue cyan yellowish green yellow and red RETURN Select this
5. In general set it to AV Average eines work properly depending on the installed lens Set the Level VR of the lens to the optimal value Set AGC to OFF and adjust the Lens VR to an appropriate brightness Adjust the Lens VR adjust the BRIGHTNESS and then check if the screen brightness changes properly Otherwise adjust the Lens VR again Manual Select Manual Lens P ESPOSURE 1 When the SETUP menu screen is displayed select EXPOSURE by using the Up and Down buttons so that the arrow indicates EXPOSURE 2 Select a desired mode using the Up and Down buttons EXPOSURE SETUP gt 1 SHUTTER ESC SHUTTER You can select either auto or manual shutter A FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually e When you use DC lens set the shutter mode to fixed if Color Rolling is occurred e When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a bright fluorescent light Therefore take care when choosing the installation position e When the SHUTTER is set to MANU
6. enter one Only English is available in the mode How to Use the Camera Press the SET button CAMERA TITLE SETUP Use the 4 direction buttons to move ABCDOEFGHIJKLM to a desired letter and select the letter HOPGRSTUUURYE by pressing the SET button Repeat RS Hare this to enter multiple letters You can 8123456789 enter up to 15 letters CLR POS END Notes e If you move the cursor to CLR and press the SET button all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the SET button Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the SET button Enter a title move the cursor to POS and WT J press the SET button The entered title Pl FRONT DOOR fyr appears on the screen Select the position to cl display the title on the screen by using the 4 direction buttons and press the SET button When the position is determined select END and press the SET button to return to the SPECIAL menu SYNC In areas where the supply is at 60Hz you can synchronize the output phase of multiple cameras using the power Brase synchronization function Line Lock Mode without using a synchronization signal generator Press SET to Return INT Internal Synchronization Type UL Power Synchronization Type Line lock e Press the SET button e You can select a desired phase from
7. that the power cord and line connection between the camera and monitor are fixed properly gt Check that you have properly connected VIDEO cable to the camera VIDEO output jack gt Check that the lens type is VIDEO lens or DC lens The image on the screen is dim gt Is lens stained with dirt Clean your lens with soft clean cloth gt Set the monitor to proper condition gt If the camera is exposed to too strong light change the camera position The image on the screen is dark gt Adjust the contrast feature of the monitor gt If you have an intermediate device set the 750 Hi z properly The camera is not working properly and the surface of the camera is hot gt Check that you have properly connected the camera to an appropriate power source The DAY NIGHT menu does not work gt Check that AGC of EXPOSURE SETUP menu is OFF The SENS UP function does not work gt Check that AGC of EXPOSURE SETUP menu is OFF gt Check that SHUTTER of EXPOSURE SETUP menu is A FLK or MANUAL The Motion Detection function does not work gt Check that MOTION DEF of SPECIAL SETUP menu is OFF Color is not correct gt Check the setting of WHITE BAL SETUP menu The screen flickers continually gt Check that direction of camera turns toward the Sun RS 485 communication fails gt Check the polarity between RS 485 Control Port and RS 485 cable 485 Control Board Connection Port RS 485 Control
8. to EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe Signature FI Cru Signature Full Name BONJENG GU Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place Date 2008 11 01 Date SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 82 31 740 8151 8 FAX 82 31 740 8145 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE CO LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungcctv com P No Z6806 0854 01C VAN 09 10
9. 10500 K INDOOR Select this when the color temperature is between 4500 K and 8500 K O OUTDOOR Select this when the color temperature is between 1800 K and 10500 K sodium light inclusion AWC SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the SET button If the environment changes readjust it O MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and then press the SET button Press SET to Return How to Use the Camera Notes e White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of environment surrounding the subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight unlike conventional cameras by adopting a proprietary SV IV DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Up and Down b
10. AL or A FLK mode SENS UP will be disabled O AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the higher the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 0 to 30dB HIGH Allows automatic gain control from 0 to 42dB SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu e If you press the SET button in AUTO mode You can adjust brightness by increasing or decreasing the shutter speed x2 x256 Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom level is increased this is normal Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Up and Down buttons so that the arrow indicates White Bal 2 Select a desired mode using the Up and Down buttons B S WHITE BAL X Select one of the following 5 modes as appropriate for your purpose ATW Select this when the color temperature is between 1800 K and
11. Port CONNECTION TERMINAL TRX 485 CONNECTION TERMINAL TRX 485 gt Check the RS 485 Communication establishment initial value RS 485 Communication establishment initial value Item Camera ID BAUD RATE UART MODE RET PKT Initial value 1 9600 8 NONE 1 ENABLE gt We recommend that you make ground connect between camera and controller in order to maintain safety communication control COLOR CCD CAMERA 36 User Guide Q Specifications SHC 745N SHC 745P SHC 745PH ELECTRICAL Input Voltage AC 24V DC 12V AC 230V Power Consumption 4 0W VIDEO Imaging Device Diagonal 8mm 1 2 Sony Exview HAD CCD Total Pixels 811 H x 508 V 795 H x596 V Effective Pixels 768 H x 494 V 752 H x582 V Scanning System 2 1 Interlace Synchronization Internal Line Lock Frequency H 15 734KHz V 59 94Hz H 15 625KHz V 50 00Hz Horizontal Resolution COLOR 560TV lines Min B amp W 700TV lines Min Min Illumination 0 05 Lux Color 0 00019 Lux Color Sens Up Mode 0 006 Lux BAN SIN Y Signal 52dB AGC Off Weight On Video Output CVBS 1 0Vp p 750 OPERATIONAL IRIS Adustment DC VIDEO Electronic Shutter Speed ESC 1 60 PAL 1 50 1 120 000 sec MANUAL A FLK 0 i NTSC Korean English Spanish Japanese French Portuguese n Screen Display PAL English French German Spanish Italian Chinese Portuguese Backlight Compensat
12. SMASUNG aoe ne Super Vision at Ultra Low Light SHC 745 User Guide Before installing and operating this product please read this manual thoroughly ENGLISH Before operating the camera confirm the camera model and proper input power voltage In order to that you can understand this manual thoroughly we ll introduce our model description E SHC 745 SERIES e NTSC MODELS e PAL MODELS SHC 745N SHC 745P SHC 745PH E MODEL DESCRIPTION e SHC 745X X POWER SOURCE SIGNAL SYSTEM e SIGNAL SYSTEM N NTSC MODEL P PAL MODEL e POWER SOURCE DC12V AC24V H AC 230V CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is A intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limit
13. ces clear picture quality with a horizontal resolution of 560 TV lines for color and 700 TV lines for B W DA pam Bu ps lt 7a By adopting a proprietary SV IV DSP chip the camera delivers clear high quality pictures even in backlight by increasing exposure in dark areas while decreasing it in bright areas a corrected image with clear details results By adopting a diagonal 8mm 1 2 highly senstive CCD and digital signal processing technology it can clearly distinguish the outline and color of a subject in an tremely low luminance environment even for iple under starlight Since surveillance is possible Samsung Super Noise ction Fanen phdg Ng vA Motion Detection Paga Since the camera detects motion and generates signals without any additional external sensors you can monitor activity more efficiently by connecting the camera to an alarm device pisq Ng VA Dis Digital Image Stabilizer A DFTA The DIS function compensates for any camera movement to produce more stable pictures UP FLIP H V REV D Z00M SHARPNESS MOTION HLC High Light Compensation S cn ed depending on its envi switches to color mode in order to maintain optimal color At night it switches to B W mode so as to obtain better picture definition Ba vy So lt gt osp DA The camera control is convenient by using 9 different foreign PAL English French German Spanish Italian Chinese Portugue
14. gnal Pin 3 Drive Pin 4 Black Ground Pin 4 Drive Lens cable lt a connector No 1 Pin No 2 Pin 4 Fit the cover of the auto iris lens connector plug remove the protective glass cover from the front of the camera and fasten the auto iris lens by turning it clockwise 5 Set focus of camera using Back Focus Control Lever of camera side after combining Auto Iris lens Back Focus Control Lever Before installing a lens identify whether the lens to be installed is a C Mount or CS Mount This camera is set for a CS Mount Lens by default To install a C Mount Lens a simple modification is required e When Using a CS Mount Lens Remove the protective glass cover at the front of this product and turn the CS Mount Lens clockwise to install it And set focus of camera using Back Focus Control Lever of camera side after combining CS Mount lens par Use the lens connector shown in the following figure If the dimensions of the connector are not correct it may damage the camera or the lens may not be installed firmly e If the lens is too heavy the camera becomes unbalanced and there may be problems Use a lens that weighs less than e When adjusting the Automatic Level Control ALC of an auto IT iris lens use Av mode if available If you use the Pk mode the picture brightness may change continuously C Mount Lens 10mm or less CS Mount Lens 5mm or less a e When Using a C Mount Lens 1 Rem
15. ion BLC HLC OFF Day amp Night COLOR B amp W AUTO ICR Gain Control LOW HIGH OFF White Balance ATW AWC MANUAL INDOOR OUTDOOR 1 800 K 10 500 K SENS UP frame Integration AUTO OFF x2 x256 Motion Detection ON OFF 8 programmable zones Privacy Masking OF OFF 8 programmable zones 3D Noise Filter SSNRII ON OFF Level adjustable Digital Zoom ON OFF x2 x10 Digital Image Stabilization DIS ON OFF Camera Title ON OFF Sharpness ON OFF Flip Mirror ON OFF Communication RS 485 Baudrate 2400 4800 9600 19200 38400 57600bps selectable Protocol Samsung Techwin Protocol Pelco D Protocol ENVIRONMENTAL Operating Temperature Humidity 10 C 50 C 30 80 RH MECHANICAL Lens Mount C CS Mount Easy Focus type Back Focus Adjustment Manual Dimension 65 8 W x60 6 H x101 9 D mm 65 8 W x60 6 H x115 D mm Weight 315g 535g COLOR CCD CAMERA 37 User Guide DECLARATION OF CONFORMITY Application of Council Directive s 89 336 EEC Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 European Representative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SHC 745P PH Beginning Serial NO 8110001 Year of Manufacture 2008 11 01 Conformance
16. m D amp N Input Port You can switch to Day amp Night Mode by connecting an external signal to this port MD Output Port Motion detection signals are output through this port RS 485 Control Port You can control SETUP MENU through this port by using external controllers like a Remote controller that RS 485 Communication is supported For details see page 21 Video OUT Port Video signals are output through this port Connect this port to the Video IN port of a monitor Power LED When power is properly connected this LED comes on Power IN Port Connect the power as specified for each model here The lens is not supplied with this camera Purchase a lens suitable for your environment This camera accepts the auto iris lens and both C and CS mount lens lt is recommended to use the DC type Auto Iris Lens to effectively enjoy the major functions of this camera e Keep the lens surface clean since if it is contaminated with dirt or fingerprints the picture quality suffers 1 Strip the insulation of the auto iris lens cable 8mm from the end approx 8mm un 2 Strip the insulation of the core of the auto iris lens cable to expose a 2mm length approx 2mm 3 Remove the cover of the auto iris lens connector plug and solder the lens cable to the comnector pin of the plug e For a Video Drive Lens e For a DC Drive Lens Pin 1 Red Power Pin 1 Damping Pin 2 NC Pin 2 Damping Pin 3 White Video Si
17. mode using the Up and Down buttons V REV You can flip the picture vertically on the screen O H REV You can flip the picture horizontally on the screen D ZOOM You can use a digital zoom of x2 x10 Press SET to Return SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture PED LEVEL COLOR Please use this menu item when using a LCD monitor other than standard ones You can change PED LEVEL and COLOR menu RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu e When the V REV or H REV mode is enabled the text on the screen does not flip e If you increase the SHARPNESS level too high the picture may become distorted or noise may appear 1 When the SETUP menu screen is displayed select SPECIAL by using the Up and Down buttons so that the arrow indicates SPECIAL b gt 5 SPECIAL 2 Select a desired mode using the Up and Down buttons B i CAM TITLE O CAMTITLE If you enter a title the title will appear on the monitor if the SPECIAL menu screen is displayed use the Up and Down buttons so that the arrow indicates CAM TITLE Set it to ON by using the Left and Right buttons Notes e When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if D 1 CAM TITLE you
18. om do ged is low To set up the sswitching time or DURATION PAST speed for AUTO mode press the SET AUTO SETUP button Press SET to Return DWELLTIME You can select the duration time about changing the day night mode 5s 7s 10s 15s 20s 30s 40 60s DURATION You can select brightness of illumination about changing the day night mode ana Mm a Fast 2 5 lux 4 lux The brightness of illumination is changeable by sw ogiz elix installed environment 1 When the SETUP menu screen is displayed select IMAGE ADJ by using the Up and Down buttons so that the arrow indicates IMAGE ADJ EXTERN This mode allows you to apply a desired filter to external signals 9 Notes gt e When using a Video Auto Iris Lens if you set the lens level to low automatic switching between Color and Black amp White may not occur e You cannot control the DAY NIGHT menu when AGC in the EXPOSURE menuis OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode e The OSD key does not work for 3 seconds when switching to Color or B W to ensure stable camera operation The camera may focus less well under infrared illumination than under normal illumination e Since the camera may not focus as well under infrared illumination at night as it does under normal illumination install an Extra low Dispersion Lens to obtain sharp pictures lt d 2 Select a desired
19. ove the protective glass cover at the front of this product and turn the C Mount Adapter clockwise to install it 2 Tum the C Mount lens clockwise to install it 3 Set focus of camera using Back Focus Control Lever of camera side after combining C Mount lens Connect the Video OUT port on the rear panel of the camera to a monitor CCD Camera i Monitor M e Since the connection procedure may differ depending on the type of monitor or peripheral device to be connected refer to the User Manual for the device to be connected e Make sure to turn off the device to be connected before making any connections e Turn the 75Q Hi Z switches of interim display devices to the Hi Z position and the switches of any final device to the 75Q position Intermediate End monitor CCD Camera Since power specifications differ depending on the model make sure to check your model name and specifications before connecting power You can connect power as shown in the following figure e Since the power specification supports both AC and DC connect AC 24V 500mA Adaptor or DC 12V 500mA Adaptor e Use AC230V 50Hz power source For SHC 745PH The camera can be controlled by using external controllers like a Remote controller RS 485 Communication 1 To control by PC Connect the RS 485 control port of the camera and the serial cable through an RS 485 converter Example PC Serial Port
20. re indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal on BY og C Use only under temperature conditions between May lower image quality 10 C and 50 C Provide good ventilation when using in high temperature conditions Severe lighting changes or flickering may hinder The lens is the most important component of normal camera operation the camera Be careful not to smear it with fingerprints May cause a product malfunction May cause a product malfunction Wipe dry any Radioactivity exposure may damage the CCD liquids Liquids may contain minerals that are corrosive to electronic components Exposure to a spotlight or an object emitting strong light may cause smear or blooming Ensure that the power source complies with normal specifica
21. s are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes e Features e Precautions e Components and Accessories e Overview E Front View E Side View E Bottom View E Rear View When Using Auto Iris Lens When Using C CS Mount Lens E Connecting a Monitor E Connecting Power E Control via RS 485 Interface e How to Use the Camera E Function Menu Structure E How to Set up the Functions EXPOSURE WHITE BALANCE BACKLIGHT SSNR DAY NIGHT IMAGE ADJ By adopting a diagonal 8mm 1 2 410 000 pixel ExView Sony CCD the camera produ
22. se Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment and is taking a number of steps to provide customers with more environment friendly products The Eco mark represents eco Samsung Techwin s will to create environment friendly products and indicates RoHS compliant that the product satisfies the EU RoHS Directive This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug when thunder crashes or lighting flashes This product is support equipment for surveillance system Therefore we can t compensate for material loss and or personal injuries by robbery fire natural disaster or something like this type paano ii Hiii Ignoring this information may SA result in material loss and or 3 A serious personal injuries including MA Hao amena loss and or a death PIS Indicates Never Allowed Indicates No Disassembling Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems ps Correct Disposal of This Product This marking shown on the product or its literatu
23. the SET button e Main setup menu is displayed on the monitor screen Select the function using 1 LEHS Dee Change the status the UP or DOWN button using the LEFT or RIGHT button 2 Select a desired function using the Up and Down buttons e Place the cursor over a desired item 3 Set up a selected item by using the Left and Right buttons 4 To finish the setting select EXIT and press the SET button Notes e An item with the icon also has sub menus To select a sub menu select an item with the icon and press the Function Setup switch e An item with the icon is unavailable due to function settings Using this function you can control screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Up and Down buttons so that the arrow indicates LENS 2 Select the connected lens type by using the Left and Right buttons P i LENS DC Video Select Auto Iris Lens e When DC is selected you can control screen brightness The range of brightness control is P BRIGHTNESS mans between 1 and 70 Adjust the brightness appropriately for optimal screen brightness Press SET to Return pa e When you use DC lens set the shutter mode to fixed if Color Rolling is occurred e Some lenses may not work properly depending on the setting of the BRIGHTNESS LEVEL e When Using a Video Type Auto Iris Lens Adjust the ALC adjustment terminal on the lens appropriately
24. tions before supplying it to the camera Ultra Low Light Color CCD Camera SHC 745 Instruction Manual Auto Iris Lens Connector Plug CMount Adapter Tripod Mounting Bracket Screw Hole Used to fix the Tripod Mounting Bracket to the top of the camera C Mount Lens Adapter Install this adapter to use a C Mount Lens Back Focus Control Lever Adjust focus by this Back Focus Lever SAMSUNG Auto Iris Lens Connector Used to connect Auto Iris Lens plug Tripod Mounting Bracket Screw Hole Used to fix the camera on a bracket or tripod 5 The screw sizes for this hole are as follows 41 4 20 UNC 20 THREAD L 4 5mm 0 2mm ISO standard or 0 197 ASA standard You can separate the Tripod Mounting Bracket and install it on the top or bottom of the camera Make sure to use the Tripod Mounting Bracket when fixing the camera to a bracket or tripod Otherwise the camera may not be secure or the internal circuitry of the camera may be damaged High Voltage Type Function Setup Button SHC 745PH e SET Button Displays the menu on the screen Press this button to confirm status or after changing a selected item e Up and Down Button Used to move the cursor up or down in the menu screen to select a desired menu item e Left and Right Button Used to move the cursor left or right in the menu screen or to change the value of the selected ite
25. to save the MOTION DET menu settings and return to the SPECIAL menu 2 Notes e MD areas show only MOTION DET menu Therefore MD areas don t display on the monitor screen COLOR CCD CAMERA 33 User Guide How to Use the Camera PRIVACY Hide an area you want to hide on the screen PRIVACY When the SPECIAL menu screen is displayed Eo oA press the Up and Down buttons so that the BB arrow indicates PRIVACY j set up the mode using the 4 direction buttons AREA SEL You can select up to 8 PRIVACY areas AREA MODE Determines whether to use the area selected in the AREA SEL and the size and position of the area paang hanang mg MASK COLOR Determine area color You can select Gray Green Red Blue Black White TRANSP Determine the transparency of selected area as controlling number from 0 to 3 RETURN Select this to save the PRIVACY menu settings and return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind The chance of resolution decrease is existed because DIS function uses the digital zoom e DIS doesn t operate when background illumination is too low e DIS doesn t operate when object pattern is monotonic as like sky or white wall e If DIS is enabled the digital zoom is not configured to less than 46 level COLOR CCD CAMERA 34 User Guide O How to Use the Camera
26. uttons so that the arrow indicates BACKLIGHT MAIN SETUP 1 LENS DC 2 EXPOSURE lt 1 Z WHITE BAL ATU B 4 BACKLIGHT OFF 5 SSHR ON 2 Select a desired mode using the Left and Right buttons depending on the camera purpose BLC Enables a user to directly select a desired area from a picture and to view the area more clearly BLC OFF COLOR CCD CAMERA 24 User Guide O How to Use the Camera HLC High Light Compensation If the scene contains extremely bright light areas such as from car headlight the light can mask out much of the on screen detail DAY In normal daylight conditions the HLC is not activated NIGHT If a high light that is larger than a certain size is present on the screen HLC is activated to remove the high light OFF Not being used 3 Select a desired mode using the Left and Right buttons and press the SET button SHE TUE Select BLC to adjust the area to be enhanced P TOP nn and enhancement level per RIGHT LEVEL HLC Enable a user to select a mask color of high light area from a picture HLC SETUP b MASK COLOR Press SET to Return Notes Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance e In a dark environment the HLC is only activated when a high light that is larger than a certain area is present
Download Pdf Manuals
Related Search