INSTALLATION MANUAL & USER'S GUIDE
Contents
1. M1 INSTALLATION MANUAL amp USER S GUIDE 483 N FRONTAGE RD NIPOMO CA 93444 PHONE 805 929 3545 1 PACKAGE CONTENTS One 1 M1 soundhole magnetic pickup One 1 pre wired strapjack assembly One 1 10 external soundhole cable One 1 3 32 Allen wrench Two 2 spare 3 4 pole pieces One 1 spare 3 8 pole piece Two 2 self stick wire clips One 1 manual One 1 warranty card 2 OVERVIEW AND CAUTIONS The M1 is a passive soundhole magnetic pickup that features outstanding body sensitivity with great warmth and presence Its dual coil design employs L R Baggs exclusive TriAxial Dynamic Technology to produce clear rich tones that are resistant to feedback noise and hum with string and body sound all in one The M1 also features individually adjustable pole pieces with smooth threadless tops Also included are two cables a 22 inch prewired strapjack assembly for permanent installations and a 10 foot guitar cable for temporary installations The M1 will fit guitars with soundholes larger than 3 55 that are centered beneath the strings Ensure that this product will fit the guitar properly before making any alterations to the instrument The installation procedure is very simple however we recommend that any woodworking for instance drilling a strapjack hole be performed by a professional dealer installer We do not provide advice or support for home or hobbyist woodworking Installers please r2. e devices such as active direct boxes will capture all of the M1 s nuances Our Para D I partners well with the M1 due to its high impedance clean gain and EQ capability Note that the length and quality of your cord will have a large influence on the sound This is because passive magnetic pickups interact with the cord capacitance to create a frequency peak that is a distinctive part of the tone Long cords move this peak frequency down and create an edgy electric tone with more midrange Short low capacitance cords move the peak up creating an airier more acoustic sounding tone These are simply general guidelines experiment with different cables to determine the best match for your guitar and equipment 4 2 Experiment with pole piece heights The pole pieces on the M1 are preset for bronze acoustic strings but this is just a starting place They are adjustable with the 3 32 Allen wrench to obtain the optimum balance and tone The height of the pole pieces relative to the strings will have a profound effect on the sound and balance of the pickup Raising the pole pieces will increase the output of the strings lowering them will decrease the output For the most powerful and articulate sound we recommend setting the pole pieces closer to the strings However if they are too close they will interfere with the strings movement and produce a percussive clacking noise Lowering the pole pieces will de emphasize the st
3. ead the instructions carefully before proceeding We will not be responsible for any damage to the guitar or personal injury resulting from installation improper installation use or misuse of the product 3 5 3 1 Installation overview There are two ways to install the M1 by using either of the two provided cables For permanent installations use the strapjack harness If the guitar doesn t have a hole in the tailblock it will be necessary to drill one in order to use the strapjack For temporary or nondestructive installations use the 10 foot guitar cable which is designed to run out of the soundhole directly into your outboard gear This is a high quality cable using it will help ensure that the M1 sounds as good as we intended The other principal advantage of this installation is that it leaves the instrument unaltered For permanent installations proceed to the strapjack instructions for temporary installations skip to the pickup installation in section 3 3 3 2 Strapjack installation If you plan to do a permanent installation be sure to try installing the M1 in the soundhole before you drill the strapjack hole The M1 will only fit in a soundhole larger than 3 5 in diameter Also a few guitars have off center soundholes that will not allow the pole pieces to be directly under the strings If you have one of these plug in the M1 using the 10 foot cord and see how well it works before you alter your
4. guitar For proper installation this jack requires a clean 1 2 hole in the tail block of the instrument If the guitar lacks this hole start by placing a piece of masking tape on the outside of the instrument over the drilling area to avoid chipping the finish drill a small pilot hole in the tail block and then follow with a step drill Now proceed with the installation Remove the strap ring retaining nut and one washer from the end of the jack There should still be one star locking washer one flat washer and a nut remaining on the jack Bring the jack down through the soundhole into the body and insert it into the pre drilled hole in the tail block Using the internal nut be sure to include the flat and star washers set the proper depth that will allow the entire smaller threaded section to protrude from the smaller instrument see figure threaded section protrudes With the jack in place lay the remaining washer over the threads and attach the external retaining nut until it s tight Finish by attaching the strap ring it should cover the retaining nut and washer Note that asserting too much pressure may crack the finish 3 3 Pickup installation Begin by plugging the strapjack harness or the 10 cable into the pickup If you are using the 10 cable loop the cord beneath the pickup and push it into the strain relief recess on the underside of the pickup until it pops into place the loop between t
5. he plug and strain relief should be rather tight Now loosen the clamp screws on either end of the pickup s top plate until the clamps are open enough to accommodate the guitar s top thickness Then slide the pickup into the soundhole and tighten the screws For small soundholes it may be necessary to remove one or both clamps slide the pickup into place then reattach the clamp s once it is correctly positioned When reattaching the clamps verify that they slide into the slot that is molded into the pickup housing Tighten the screws snugly but don t overdo it this can damage the pickup or guitar finish If you are concerned about the possibility of the M1 Active damaging the instrument s finish consider applying thin cork pads not included between the clamp and guitar However note that the clamps have been left unpadded to improve coupling between the pickup and guitar body Because the M1 reads the top resonances that provide depth and warmth using cork pads may dampen this sensitivity and adversely affect the pickup s responsiveness For permanent installations be sure to secure the wire with the two self stick wire clips provided so that it does not hit the inside of the guitar during stage movement 4 USER S GUIDE 4 1 Plugging in The M1 will plug into practically anything with good results Low impedance inputs such as those found on mixing boards will flatten the sound and reduce the pickup output High impedanc
6. rings and emphasize the body sound We have provided two additional 3 4 pole pieces for use in the B and little E string positions with nickel or electric guitar strings and one spare 3 8 pole piece for use with acoustic sets that have an unwound G string When adjusting the pole pieces downward you will meet additional resistance when you reach the bottom of the adjustment range Do not force the pole pieces any further This could damage the pickup permanently 4 3 Mixing with other sources The M1 is intended to provide a complete sound from a single passive pickup However you may still want to pair it with another transducer The prewired strapjack harness has stereo output capability You can connect the output wire from a mini mic or another transducer to the ring terminal of this jack Then run a stereo cord to the L R Baggs Mixpro or your favorite outboard gear The M1 can easily be substituted for other soundhole pickups in an existing two source setup As with all two pickup setups you should experiment with relative phase if possible The two sources will often mix much better in one phase than the other
Download Pdf Manuals
Related Search