LiPoBalancer Operating Instructions, Software V8 and
Contents
1. 1 1 3 2 1 3 3 type selection Exception SetFilterOn Off command conductive when green Sicherheits E is Anachiuss BAL Ss 3 VAVA V 33 3 i J Schulze BalCab10 balancer Ideal for Schulze LiPoPerfekt Safety sockets for looped through charge lead charge lead red to be connected there This cable must be plugged into the socket on the batte ry charger Schulze BalCab20 balancer socket for 2s 8s packs resp 2s 14s packs Of course ideal for Schulze LiPoPerfekt battery packs Conventional balancer socket 7 pin JST connector for 2s 6s packs Graupner and Robbe compatible Note software updates automatically detect the circuit board version you are using BUT software versions 1 to 6 must not be loaded into the present circuit board version Battery type setting only if a Schulze BalCab 10 or BalCab 20 balancer lead is not used The jumper has been replaced by a push button as the LiPoBalancer now supports four battery types Three LEDs are now used to indicate the jumper setting Blue Li Po Orange Li lo Yellow Li Fe Saphion cells All off Nickel Ni Cd Ni MH Set up instructions battery type Hold the push button pressed in Connect the balancer lead All the LEDs light up the balancing LEDS then go out Release the push button The battery type LEDs cycle through all four states listed under 1 2 at one second inte2. F 7 i Operating Instructions Page 1 Issue 05 06 LiPoBalancer Supplement mainly for PCB version with L Issue 05 06 Page 2 8 14 red cell count LEDs When using the conventional balancing connector DAS Battery type select Perfekt System by push button DX f r Ihre Li Po Li lo gk Lithiumakkupflege Li Fe Nickel O e teeers eens resp as configu o OBM paeka boi jodan Lasetuetand wanrend red via RS232 SIP Leceverseness F 4 p oder auch stand alone i gt 3 Eran bw Tnisdestromen bat 3 Q sso 1 14 Zellenzahi RS232 interface COM port for exporting charge data and importing firmware updates indicate balancing process Display of the Battery type iPoBalancer Operating Instructions Software V8 and later Safety circuit is active EIN LED is glowing LiPoBal 14 Der LiPoBsiancer wird Gber den ein Balancer aktiy thiumakkupack mit Strom versorgt CE 3 socket for 2s 4s packs battery packs Dear customer In the course of product maintenance we have introduced some minor modifications to the LiPoBalancer Some parts of the original operating instructions are affected by this and no longer apply All the differences are listed in this separate sheet which is valid only for the version of the circuit board with a push button for battery type selection NOT VALID for the circuit board version with a jumper for battery 1 1 1 2 1 3 1 3
3. election by push button draws less current when asleep compared to the earlier jumper model only 1 6 mA sleep current according to the cell count connect ed to it Universal socket JST connector The socket for Graupner or Robbe battery packs has now moved to the front end of the circuit board Batteries consisting of up to six cells can be balanced using the 7 pin socket Please ensure that the negative terminal of the battery is connected to the outermost connecting pin on the left towards the edge of the circuit board see also the text printed on the front panel Important only ONE of the three balancer connectors may be used at any one time 8 4 8 5 8 6 9 4 1 9 9 4 1 10 9 4 1 11 9 4 1 12 Connecting several packs simultaneously to the same or different sockets will cause damage to the balancer New LED Displays When different errors occur then also different error messages are displayed The corresponding LEDs show the codes one after the other The calibration of the Balancer got lost All LEDs are flashing simultaneously You have to send the LiPoBalancer for a service to Weiterstadt More than 8 cells are connected to a LiPoBal 08 The balancer is not able to balance the pack The LED of the cell 8 shows missing cell blinks 2 times the balancer refuses to work At over voltage of one or more cells the balancer does not go to sleep but the safety circuit is opened The
4. green EIN LED goes out The balancing of the cells in the pack goes on the high voltage decreases When 9 4 1 9 SetFullSleep is set then the balancer goes to sleep after the battery is fully balanced New SET commands SetFullSleep Balancer goes to sleep when the voltage of the pack falls charger has switched off and the cells are no longer being balanced SetFullAlive Balancer only goes to sleep if cell limit values are exceeded or if the push button is held in for two full seconds SetFilterOn Also available on PCBs with the battery type selection jumper When a battery is charged with refresh pulses then the caused voltage spikes are suppressed as good as possible For this reason it is possible to use the LiPoBalancer also connected to those chargers the refresh pulses can not be switched off SetFilterOff The spike filter is switched of for a genuine voltage value output at a spike free charge discharge AYATA Schulze Elektronik GmbH Prenzlauer Weg 6 64331 Weiterstadt e Fon 49 6150 1306 5 Fax 1306 99 www schulze elektronik gmbh com e Germany hotline schulze elektronik gmbh com
5. rvals pushbutton 1 3 4 Press the button exactly when the LED matching your battery type lights up The selected type will be indicated for a period of three seconds The normal POWER ON indicator moving strip etc is then displayed and the balancer carries out its work Additional push button functions If the unit stops balancing because a limit value is exceeded and the safety circuit has been triggered the balancer displays the reason for the shut down over voltage under voltage etc After this it goes to sleep completely in order to save current but it can be woken again with a brief press on the button Alternatively if you hold the push button pressed in for two seconds to wake it up the usual POWER ON procedure is followed by a display of flashing error code LEDs the flashing LEDs are those which exceed ed the limit value and which resulted in the shut down before the balancer went to sleep This does not apply if the LiPoBalancer detects that the battery has in the meantime been replaced by another pack with a different distribution of cell voltages If the condition which led to the shut down still persists the balancer will again go to sleep after one minute other wise it resumes working If you hold the button pressed in for two seconds in normal use the LiPoBal goes to sleep which also causes the integral safety circuit to be isolated Note the current circuit board with the battery type s
Download Pdf Manuals
Related Search