P5/16PRF+ - Becker
Contents
1. 53 Operating mode S2 4 Min Protection class IP 44 Min tube diameter mm Frequency 868 3 MHz Malfunction Tubular drive is not running No transmitter has been programmed Transmitter is outwith the range of the tubular drive Transmitter has been operated outwith the range several times Batteries in the transmitter have been in correctly inserted not inserted at all or are empty Faulty electrical connection Thermal cut out function in the tubular drive has been activated Programme new transmitter Move transmitter into the range of the tubular drive Activate the control or stop button on the transmitter at least 5 times Insert batteries properly or replace batter ies 5 Check electrical connection 6 Wait 5 10 minutes You are unable to change the axle direction The axle direction is incorrect after deleting the end limits End limits are stored in the tubular drive The axle direction switch is in the wrong posi tion Start up the tubular drive via a start command and deactivate with a stop command Then delete the end limit settings using the pro gramming and stop buttons Slide the axle direction switch to the opposite position Tubular drive has stopped at random and won t run in the given direction 1 Tubular drive has detected an assumed load 2 Tubular drive is overloaded 1 Run the drive briefly in th2. P5 16PRF P9 16PRF R8 17PRF R40 17PRF Roller Shutter Drives with integrated radio receiver Becker Antriebe GmbH _ Ky ww 35764 Sinn Germany ee BECKER WS www becker antriebe com Assembly and Operating Instructions Table of Contents Ge Melia sesseseress noeasias uiis teh uate eiades E E a ara a E E aa adit chic vieaw eth a a a aan levee een aa 2 Warranty sacectercceaateives fatiene tad el E E vk sic Uadaa Libs a E Gated al eae eaten ead aed a ete ream erected 3 Safety MOMMA OM assis 00 sdk otk n De sa bch ad O se deena ae ds salle Deane aa aa a E ancien sed a a aa eE E asin EEEE 3 Intended USE esas ees ceca ec Haws te digs gee end E ee nace a ld ins Se chicane ae neces ces O aware Shed addtional pepe cates 5 Mounting and Installation INSTFUCTIONS 2 sess deicees exisiasce wiaes sire tien seanoir a pune se aire in EAER ve TE Ea ened 5 Programming the SwWitChinG TIMES cesiune a E EE EEEE EE EE E E ETE EEEE andes dee 13 D l ting the Switching tinme Siss neea a e EE A E T E EEE NEA E EE EE AET E a E 13 Technical Data race nionean ea E E a O E EE E aR 14 Whatshould you doie nimenne e a E E S E a e E E EE E EEES 15 Biief instructions commissioning PREF siiciscanecdecenoresans tes a aE a E a a a aE aaa 16 General The roller shutter drives P5 16PRF to P9 16PRF and R8 17PRF to R40 17PRF are high quality products with a wide range of interesting features Radio controlled individual multi point group and ce
3. ad to serious injuries e All operational work including maintenance and cleaning on electrical installations as well as other parts of the construction must always be performed by authorised specialists especially by qualified electricians e Do not allow children to play with control units e Systems have to be regularly checked by authorised specialists for wear and damages e Always put damaged systems out of operation immediately until they are repaired by an authorised specialist e Donot operate equipment if people or objects are within the danger zone e Observe the danger zone of the equipment during operation e Bring the equipment to a stop and disconnect the mains power supply when maintenance and cleaning jobs are performed either on the system itself or in the immediate vicinity of it e Ensure that there is an adequate distance at least 40 cm between moving parts and adjacent objects e Crushing and shearing points must be avoided or protected BECKER 3 Assembly and Operating Instructions A Important safety instructions for the installation and commissioning Caution Failure to observe these instructions can lead to serious injuries Please comply with the safety instructions EN 60 335 2 97 Please note that these safety instructions cannot be assumed as being complete since this standard does not consider all the possible causes of risk For exa mple the construction of the operated product the effectiveness of the
4. ating Instructions Bearer plate Mounting pin P5 16PRF to P9 16PRF R8 17PRF to R20 17PRF Drive adapter with safety catch Drive adapter R30 17PRF to R40 17PRF M6x12 screw sm Plain washer Toothed lock washer Drive adapter gt i To install the drive the following instructions must be followed carefully e Removing the mounting pin The mounting pin engages automatically when inserted To remove the mounting pin slide the bearer plate upwards and pull out the mounting pin e Mounting the drive adapter with safety catch P5 16PRF to P9 16PRF R8 17PRF to R20 17PRF The insert direction for the drive adapter is determined by the drive adapter type Shape When inserting the drive adapter with safety catch ensure that the catch engages with the location lug You will hear a clicking sound when the drive adapter has engaged properly Pull lightly on the drive adapter to ensure that it has been fitted securely e Mounting the drive adapter with screw connection R30 17PRF to R40 17PRF In this case the drive adapter is fastened with a M6x12 screw which is se cured by a M6 plain washer and a corresponding toothed lock washer 3 The drive adapter of the tubular drive is connected to the roller tube as fol lows Size of drive Roller shutter tubes Torque max Fastening screws mm mm Nm for drivers 4 x 40 mm plastic drive flat h
5. ation Always observe these assembly and operating instructions when installing and setting the device Warranty Structural modifications and incorrect installation which are not in accordance with these and our other instructions can result in serious injuries e g crushing of limbs Therefore structural modifications should only be carried out with our prior approval and in accordance with our instructions particularly the information contained in these Assembly and Operating Instructions Any further processing of the products which does not comply with their intended use is not permitted The end product manufacturer and fitter have to ensure that all the current statutory official regulations and in particular EMC regulations are adhered to during utilisation of our products especially with regard to end product assembly installation and customer advice Safety Information The following safety instructions and warnings are intended to avert hazards and to prevent damage to property and personal injuries Please retain for future reference Caution Denotes a potentially hazardous situation If this is not avoided injuries may A result Attention Denotes a potentially hazardous situation If this is not avoided the product or V something in its vicinity may be damaged IS Note Denotes user tips and other useful information A Important safety instructions for the user Caution Failure to observe these instructions can le
6. button The tubular drive makes a clack clack Within 3 seconds also hold the DOWN sound to confirm w y button and keep both buttons pressed The intermediate position has been de Clack Clack leted 9a Via B Ab 9b A x 9c A 2x SA 10 Clack Clack Clack Clack Clack Clack Action Response 9 Ventilation position Note LS This function is used to move your roller shutters from the lower end limit upwards in order to open the ventilation slats The ven tilation position can only be set after the two end limits have been set 9a Setting the ventilation position Adjust the shutter into the desired ven tilation position First press and hold the STOP button Within 3 seconds also press the UP but ton and keep both buttons pressed The tubular drive makes a clack sound to confirm The ventilation position has been stored 9b Adjusting the shutters into the ventilation position Note Ls The shutters move into the ventilation position from the lower end limit Press the UP button twice within one second 9c Deleting the ventilation position Adjust the shutter into the ventilation position First press and hold the STOP button Within 3 seconds also press the UP but ton and keep both buttons pressed The shutter curtain moves into the ven tilation position The tubular drive makes a clack clack sound to confirm The ventilation position
7. cations are not permitted in order to protect the safety of the users and others since these actions can impair the system s safety resulting in personal injuries and property damage Becker Antriebe shall not accept liability for damages arising from such actions Always observe the information in these instructions when operating or repairing the system Becker Antriebe shall not accept liability for damages resulting from incorrect usage Attention V Anti lifting devices may only be used if sufficiently rigid roller shutter laths made of aluminium steel or wood are used When closed the shutters must not extend over the guide rails as this may put too great a load on the joint between the top two slats which could consequently be damaged Before reaching the lower end limit the roller shutters must have made at least 1 5 revolutions This is normally the case when the window height is five times the effective tube diameter Example 60 series octagonal tube with anti lifting device from Zurfluh Feller Effective tube diameter 9 cm gt min window height gt 45 cm Mounting and installation instructions Mounting the roller shutter drive Attention V Drives from Becker Antriebe are to be mounted and operated solely with mechanical accessory components shown in the current Becker product catalogue Prior to mounting the fitter must ensure that the masonry and the shutter box are sufficiently robust drive torque plus weight of th
8. ch is set to Clock this roller shutter command is repeated every 24 hours The position of the manual auto sliding switch is unimportant when programming the switching time All previously stored switch ing times are deleted accordingly 1 Adjust the roller shutters if necessary until they are in the limit position opposite to the desired running direction 2 Wait until the time at which the automatic control command is to be executed 3 At the preset time activate the desired direction key and hold down until the roller shutter system stops briefly after approxi mately 6 seconds and then moves unto the limit position 4 Release direction key The tubular drive will automatically store the current time for this control command Deleting the switching times IE Note Both switching times are always deleted in this process In order to delete the times the UP and DOWN control commands are to be triggered press the STOP button for 10 seconds This is acknowledged by a double click of the tubular drive The switching times have been deleted BECKER i Assembly and Operating Instructions Nominal torque Nm Technical Data P5 16PRF P5 20PRF P9 16PRF R8 17PRF R12 17PRF R20 17PRF 8 R30 17PRF R40 17PRF Output speed min 17 Limit switch range Mains voltage 64 revolutions 230 V AC 50 Hz Power consumption W al 125 Nominal current consumption A 0 5 0
9. drive in the location of installation or the mounting of the final product in the end user s place of usage cannot be taken into consideration by the drive manufacturer If any questions or concerns regarding the safety instructions contained in the standard arise please contact the manufacturer of the respective part or end product All operational work including maintenance and cleaning on electrical installations as well as other system parts must always be performed by authorised specialists especially qualified electricians During operation of electrical or electronic equipment and units certain components are subject to a hazardous electrical voltage Physical injuries or damage to property can result in the event of unqualified interventions or failure to comply with the warning notices All applicable standards and regulations for the electrical installation must be complied with Only use spare parts tools and additional devices which are authorised by Becker Unapproved third party products or modifications to the system and its accessories represent a risk to your safety and the safety of others This means that the utilisation of unapproved third party products or modifica tions which have not been agreed with or approved by us are prohibited We shall not accept liability for dam ages arising from such actions Before installation shut down all lines and control devices that are not essential for operation Position control devices w
10. e opposite direc tion then activate the desired direction again 2 Use a tubular drive with a greater torque Rohrantrieb nimmt keine Schaltzeiten an Eingelernter Sender hat keinen Hand Auto Schiebeschalter Sender mit Hand Auto Schiebeschalter verwenden Switching times cannot be stored in the tubular drive 1 The manual auto sliding switch is set to Y 2 Several sliding switch transmitters are pro grammed in the tubular drive One manual auto sliding switch is set to Y 1 Adjust the manual auto sliding switch to 2 Adjust the sliding switch of one transmit ter to If the sliding switch is already set to slide the switch briefly to Y and back to again The switching time settings keep changing Frequent 230V supply voltage interruption Fluctuations in the 50 Hz power frequency Tubular drive is not adjusting the shutters into the preset ventilation and intermediate positions During programming travel the drive does not reach the limit stop which is to be pro grammed The upper end limit has been set first For safety reasons the drive reacts cautiously to unsmooth running during programming travel thus preventing damages The end limits have to be reset Remember to set the lower limit first Briefly travel DOWN and subsequently UP until you reach the upper limit stop 15 BECKER Assembly and Operating Instructions Brief instructions commissi
11. e shutters Caution A These drives may not be operated with conventional switching elements switches timers or similar If the roller shutters are to be operated in the opposite direc tion to the upper stopper the shutters must be stopped from being wound up into the shutter box by stoppers or by a right angled end slat We recommend fitting covered stoppers into ele the guide rails prior to mounting M 1 The lateral spatial requirements M for the box end the counter bearing j x a and the motor bearing must be determined in order to calculate the required I 4 length of the roller tube The length L of the roller tube is equal to the clear dimensions of the roller shutter box X minus the total length of the wall bracket box end M and counter bearing G L X G M Measure the distance from the wall bracket and connecting head as this may vary depending on the drive and bearings used 2 Secure the wall bracket and the counter bearing Attention V If anti lifting devices are being used closed bearings must be used When the shutters are closed the tubular drive pushes the shutters downwards to prevent them from being raised or forced open Always use suitably robust shutters for example made of aluminium steel or wooden To prevent the shutters from being damaged the entire shutter must run in guide rails BECKER 5 Assembly and Oper
12. eaded sheet metal adapter screw ST 4 8 x 10 DIN 7982 60 70 mm 45 plastic or diecast drive adapter 35 flat headed sheet metal screw ST 6 3 x 10 DIN 7982 Becker also recommends that the counter bearing be joined to the roller tube Attention V When drilling the roller tube do not drill in the area around the tubular drive The tubular drive must be inserted carefully into the tube It should not be hammered or simply dropped into the tube The shutters can be secured using springs or anti lifting devices only Profile tubes Attach a suitable limit ring adapter A and drive adapter B to the tubular drive After having done so slide the drive into the tube so that it engages positively When doing so ensure that the limit ring adapter and drive adapt er fit securely into the tube For some drive adapters the slot width tolerances of different roller tubes can be compensated by turning the drive adapter into another slot recess These slot recesses have different dimensions and allow you to mount your drive accurately Round tubes Release the tube at the motor end to allow the cam of the limit ring adapter to be slid into the tube There must be no clearance between the cam of the limit ring adapter and the tube For limit ring adapters without locating cams the roller tube must be connected to the limit ring adapter using a 4 8 x 10 mm tapping screw 4 Insert the tube into the bearing and secure the mot
13. has been de leted 10 Learning additional transmitters Note In addition to the master transmitter up to 15 transmitters can be learnt into the tubular drive system Press the learn button of the master transmitter programmed in 3 for 3 sec onds Now press the learn button of a new transmitter which is unknown to the tubular drive for 3 seconds In doing so the tubular drive goes into the pro gramme mode for a new transmitter for 3 minutes Now press the learn button of the trans mitter to be programmed for a further 3 seconds The tubular drive makes a clack sound to confirm The tubular drive makes a clack sound to confirm The tubular drive makes a clack clack sound to confirm The new transmitter has been pro grammed BECKER 1 Assembly and Operating Instructions Action 11a 11 Deleting transmitters 11a Deleting transmitters individually Note Response The master transmitter which was programmed in point 3 cannot be deleted It can only be overwritten see Point 12 Press the learn button on the master transmitter for 3 seconds The tubular drive makes a clack sound to confirm The tubular drive makes a clack sound The tubular drive makes a clack clack The transmitter has been deleted from The tubular drive makes a clack sound The tubular drive makes a clack sound The tubular drive makes a clack clac
14. hin 3 seconds also press the DOWN button for the lower limit or the UP but ton for the upper limit and hold both buttons The tubular drive makes a clack sound to confirm The new limit position has been stored 6b Increasing the shutter travel distance the desired limit position is outwith the existing travel distance Adjust the shutters to the limit position which you wish to extend First press and hold the learn button Within 3 seconds also press the STOP button and hold both buttons pressed for 10 seconds Now adjust the shutters into the new desired limit position First press and hold the learn button Within 3 seconds also press the DOWN button for the lower limit or the UP but ton for the upper limit position and hold both buttons The tubular drive makes a clack clack sound to confirm The end limit has been deleted The tubular drive makes a clack sound to confirm The new end limit has been stored The final limit position becomes fixed after the tubular drive has turned off automatically in the desired position three times BECKER 2 Assembly and Operating Instructions Action Response 7a 7 Deleting end limits Note The end limit settings can only be deleted via the master trans mitter 7a Deleting the end limits individually Adjust the shutter into the end limit po sition to be deleted The tubular drive makes a clack clack sound to confirm The end lim
15. it has been deleted First press and hold the learn button Within 3 seconds also press the STOP button and keep both buttons pressed Clack Clack for 10 seconds 7b 7b Deleting both end limits Adjust the shutter curtain into any posi y A tion between the two end limits First press and hold the learn button The tubular drive makes a clack clack Within 3 seconds also press the STOP sound to confirm a button and keep both buttons pressed Both end limits have been deleted Clack Clack for 10 seconds 8a 8 Intermediate position Note The intermediate position can be set at any given position and lies between the upper and lower end limits The intermediate position can only be set after the two end limits have been set 8a Setting the intermediate position Adjust the shutter curtain into the de y A sired intermediate position First press and hold the STOP button The tubular drive makes a clack sound Within 3 seconds also hold the DOWN to confirm y button and keep both buttons pressed The intermediate position has been Clack stored 8b 8b Moving the shutter into the intermediate position Note The shutter moves into the intermediate position from the upper end limit Press the DOWN button twice within The shutter curtain moves into the in one second termediate position 8c 8c Deleting the intermediate position Adjust the shutter into the intermediate position y x First press and hold the STOP
16. ithin sight of the driven product at a height of over 1 5 m Ensure that there is an adequate distance at least 40 cm between moving parts and adjacent objects Nominal torque and duty cycle must be suitable for the requirements of the driven product Technical data nominal torque and service life are located on the type plate of the tubular drive Moving parts of drives intended to be installed at a height of less than 2 5 m above floor level or other access level need to be protected Crushing or shearing points must be avoided or protected Observe safety distances in accordance with DIN EN 294 When installing the drive an all pole separation capability from the mains with at least 3 mm contact opening width per pole must be provided EN 60335 If the mains connection cable is damaged it may only be replaced by the manufacturer Drives with a HOSVV F connection cable are only to be used inside the building Drives from Becker Antriebe are to be mounted and operated solely with mechanical accessory components shown in the current Becker product catalogue Intended Use All P5 16PRF to P9 16PRF R8 17PRF to R40 17PRF tubular drives are intended solely for the operation of roller shutters The tubular drive is fitted with springs which support both the shutter suspension and mechanical anti lifting devices e g Zur fluh Feller Simu GAH Alberts or Deprat These are detected automatically Other applications utilisation and modifi
17. k All transmitters except the master Clack Now press the learn button of the trans mitter to be deleted for 3 seconds to confirm Clack Then press the learn button of the transmitter to be deleted for a further sound to confirm 10 seconds Clack Clack the tubular drive 11b 11b Deleting all transmitters except master transmitter Press the learn button on the master transmitter for 3 seconds to confirm Clack Now press the learn button on the mas ter transmitter for a further 3 seconds to confirm Clack Now press the learn button on the master transmitter for a further 10 sec sound to confirm S onds Clack Clack 12a 12 Overwriting the master transmitter have been deleted from the receiver There are 2 ways to overwrite the master transmitter a Activate tubular drive programme mode by switching on the power supply b Activate tubular drive programme mode using the radio switch Mains connection Motor cable 12a Activating the tubular drive programme mode by switching on the lt P __ blue power supply Switch off the tubular drive s power The tubular drive goes into programme supply and switch back on after 5 sec mode for 3 minutes Pee e onds n brown es OWT oe mumngreen rR No 3 E ppl yellow To ensure that the new master transmitter is programmed into the KS desired tubular drive only all other tubular drives which are con nected to the same power supply
18. must be deactivated from the programme mode To do so after switching back on the power supply execute a control or stop command using the transmitter for the given drives or adjust the radio switch from the inner to the outer position If the radio switch is already in this position slide the switch inwards and then back to the outer position Now press the learn button of the new The tubular drive makes a clack clack master transmitter for 10 seconds sound to confirm The new master transmitter has been Clack Clack programmed and the old master trans mitter has been deleted Action Response 12b 12b Activating the tubular drive programme mode with the radio switch Slide the radio switch into the inner po The tubular drive goes into programme sition If the radio switch is alreadyinthis mode for 3 minutes position slide the switch outwards and t ie l t 5 then back to the inner position again Now press the learn button of the new The tubular drive makes a clack clack master transmitter for 10 seconds sound to confirm The new master transmitter has been Clack Clack programmed and the old master trans mitter has been deleted ujj Programming the switching times LS Note This function is only available with the transmitters MemoControl MC441 and MC411 from Becker Centronic control programs Every tubular drive can store switching times for one UP and one DOWN command If the sliding swit
19. ntral control No wiring required to the switch or to a relay control Drive and transmitters may be combined as you wish Installation possible without stoppers lower limit to upper limit Intermediate position setting Ventilation position setting Flexible radio controlled group control which can be changed at any time without complex installation Timer function with Synchronised Sequence and Power Failure Correction Synchronised Sequence function gives the optical impression of an occupied house Automatic detection of upper limit via intelligent electronic system Automatic detection of lower limit in connection with the anti lifting lock system axle shaft safety catch es Secure anti lifting lock system Slight pressure applied to the shutters prevents them from being raised or forced open Suitable for rigid aluminium steel and wooden profiles e The limits do not have to be re set the shutter is realigned automatically if there are any changes in shut ter length due to the use of stoppers at the upper limit Emergency stop control in accordance with the European Union Machinery Directive anti restart device Torque control prevents the shutter from being damaged in the event of the shutter system being frozen or blocked Optimum closing torque adjustment Considerably less strain on the shutter and the stoppers even in systems with insulating plaster Longer service life thanks to smooth system and drive oper
20. odefor 3 minutes If several tubular drives are to be connected in parallel one of the tubular drives can be deactivated from the learn mode by sliding the radio switch into the outer position after having switched on the power supply 2b Activating the tubular drive learn mode with the radio switch Slide the radio switch into the inner position If the switch is already in this position move the button into the outer position and back to the inner position again The tubular drive goes into learn mode for 3 minutes 3 Learning the master transmitter When the drive is in learn mode press the learn button and hold for 3 sec onds RS Note The tubular drive makes a clack clack sound to confirm The learn process is complete If a transmitter had already been programmed in the receiver press and hold the learn button for 10 seconds 4 Checking the axle direction Press the UP or DOWN button If the shutter moves in the desired di rection gt the axle direction is OK If the shutter moves in the wrong direction the axle direction has to be changed This is done as follows Slide the axle direction switch into the opposite position The axle direction has been altered Re check the axle direction BECKER g Assembly and Operating Instructions 5 Setting the end limits iS a Lower position to upper position without stopper b Lower position to upper stopper 5a eo Pe 86 l
21. oning PRF Caution A Always adhere to the information contained in the assembly and operating instructions during commission ing operation and repair work The manufacturer or supplier shall not accept liability for personal injuries property damage or consequential damages resulting from non adherence to the instructions 1 Connection Connect the wires to the power supply as displayed in the ex ample below Mains connection Motor cable Blue Blue N es XN a Black L1 Black Q Green Yellow PE n N S The brown wire and black wire are connected together at L Green Yellow 2 Learning the master transmitter Press the learn button at the master transmitter until the tubular drive makes a clack clack sound Slide the radio switch to po sition The tubular drive goes into learn mode for 3 minutes 3 Checking Correcting the axle direction If the axle moves in the wrong direction change the position of the axle direction switch on the tubular drive Alter axle direction The axle direction can only be altered if end limits have not been set 4 Setting the end limits Lower position to upper position without stopper Travel to the desired lower end limit position Subsequently press the learn button and the DOWN button un til the tubular drive makes a clack sound a Clack Travel to the desired upper end limit po
22. ons Then move the shutter up towards the permanent upper stopper The tubular drive makes a clack sound to confirm The tubular drive switches off automati Cally The end limits have been set to 5c Anti lifting device at the lower limit to upper position without stop per Adjust the shutter downwards until they reach the lower limit position Then adjust the shutter into the desired upper limit position First press and hold the learn button Within 3 seconds also press the UP but ton and hold both buttons The tubular drive switches off automati Cally The tubular drive makes a clack sound to confirm The end limits have been set 5d 6a 6b eo lt 4 0 lt y Clack Clack Clack Action Response to 5d Anti lifting device at the lower limit to upper stopper Adjust the shutters until they are in the lower limit position Then adjust the shutters up towards the permanent upper stopper The tubular drive switches off automati cally The tubular drive switches off automati cally The end limits have been set 6 Changing the limit position settings Note The limit position settings can only be changed via the master transmitter 6a Decreasing the shutter travel distance the desired limit position is within the existing travel distance Adjust the shutters into the new desired limit position First press and hold the learn button Wit
23. or end in the drive bear ing 5 After the transmitter programming position the roller tube such that the roller shutters can be secured with springs Alternatively install the anti lift ing lock in accordance with the manufacturer s stipulations rR Note When using springs we recommend that at least 3 are used For longer roller tubes 3 springs are to be used per meter of roller tube Install motor connecting cable to the tubular drive in ascend ing direction and secure The motor cable and the antenna must be well clear of the winding space Sharp edges must be covered Acknowledgement The roller shutter drive acknowledges every programme setting or deletion process with a clack or clack clack sound A UP button m STOP button y DOWN button Learn button 1 2a Mains connection Motor cable blue blue N Da n black black 1 brown green green ellow ellow 2b Clack Clack 4 Axle direction switch Radio switch Radio switch Axle direction switch Action Response 1 Connecting the tubular drive Connect the tubular drive to the power supply and open the battery compart ment of the hand held transmitter 2 Activating tubular drive learn mode 2a Activating the tubular drive learn mode by switching on the power sup ply Switch on the power supply LS Note Thetubulardrivegoesintolearnm
24. sition Subsequently press the learn button and the UP button until the tubular drive makes a clack sound Clack com w _ With permanent stoppers stopper for the upper end limit or anti lifting devices for the lower end limit the tubular drive automatically stops during installation travel and automatically saves the end limit s 5 Deleting the end limit s Press the learn button and the STOP button until the tubular drive makes a clack clack sound Em al A A v Clack Clack w If the tubular drive is located between the end limits both end limits are deleted If the tubular drive is located at one of the two end limits only the respective end limit is deleted 2010 300 255 0a 09 07 e gt
25. t 5b lt 5c Note The end limits can only be set via the master transmitter The axle direction setting must be correct When the end limits are being set the tubular drive remains in lock in mode The lower end limit must always be programmed first When setting the upper end limit it is important to ensure that the shutter is securely in the guide rails There are 4 possible ways to set the end limits y Clack c Anti lifting device at the lower limit to upper position without stopper d Anti lifting device at the lower limit to upper stopper Action Response to 5a Lower position to upper position without stopper RS Note For this end limit setting there is no automatic shutter curtain ad justment Adjust the shutter into the desired lower limit position First press and hold the learn button Within 3 seconds also press the DOWN button and hold both buttons Then adjust the shutter into the desired upper limit position First press and hold the learn button Within 3 seconds also press the UP but ton and hold both buttons The tubular drive makes a clack sound to confirm The tubular drive makes a clack sound to confirm The end limits have been set to 5b Lower position to upper stopper Adjust the shutter into the desired lower limit position First press and hold the learn button Within 3 seconds also press the DOWN button and hold both butt
Download Pdf Manuals
Related Search