Operating instructions
Contents
1. or similar application Cutout 52mm optionally with adapter for cutout 60mm order code 735 rear view 8 T aem Battery hour counter input Hour counter 6 active 2 key operated switch Service hour counter EEE ol pees relay ia relay Key switch Z battery ga 3 4 hour counter input Relay Al dod battery i 4 7 battery adjustable potentiometer reset button option P Se N 3 i N W Of oS Se Se Electrical connection The instrument must be installed by an authorised specialist The relevant conditions must be observed in particular the operating voltage of the controller must agree with the rated voltage of the battery see rating plate 855 855 855 5 Check the correct polarity of the relay contacts ee ee UN X LS Function and operation 1 red LED Charge battery re 2 yellow multi LED bar display for residual capacity of battery 3 OB ZA 3 LC display for hour counter O 4 operation indication for hour counter w ae bo f Technical data p Operat2. Operating instructions BAUSER Battery and time controller Type 855 Please note Read this operating instructions carefully In the event of questions please contact your dealer or BAUSER directly Pay attention to the battery manufacturer s information and ensure that the installation and operating conditions described below are observed since otherwise you may lose your warranty rights Note in particular the information on the valid protection conditions in the section Electrical connection or the protection regulations applicable in your country Type Function 855 battery and time controller 855 1 battery and time controller with integrated service counter 855 5 battery controller 855 6 battery controller without relay contact Functions The BAUSER battery and time controller of type series 855 monitors the residual capacity at discharge of traction batteries and according to the type of the controller it also registers operating hours An additional relay contact protects the battery against exhaustive discharge Optional the controller can be delivered with integrated service counter The controller is adjustable to the different battery types by the exhaustive discharge voltage via potentiometer on the rear of the unit In order to activate a new adjustment the unit has to be reset The factory set standard discharge voltage is 1 73 V cell When choosing another adjustment we recommend to verify the correct discharge voltag
3. e The residual capacity of the battery is monitored via a multi LED bar display 1 red LED 7 yellow LEDs 2 If the residual capacity falls under the limiting value pre warning approx 25 the yellow LED starts flashing When reaching the discharge voltage the red LED 1 lights and the relay contact pins 3 4 opens In order to complete e g a lifting operation the relay contact can be closed one more time for approx 30s by switching the key operated switch off and on There are 2 possibilities to reset the controller battery is separated from the vehicle reset voltage is 2 09V cell reset voltage has to be exceeded for approx 4 sec battery remains in the vehicle while charging reset voltage is 2 35V cell The operating hours are indicated by a LC display Type 855 1 The current status of the service down counter is indicated for a period of 5 sec every time the unit is turned on or the key switch is turned on resp After termination of the service time Service counter 0 the service counting status is indicated in the LC display flashes The service counter is resetable via the reset button on the rear of the controller Exhaustive discharge voltage in V cell adjustable via potentiometer on the rear of the controller OA B D E GK eK Delivery The BAUSER battery and time controller is delivered with mounting staff and plug connector Mounting The controller is applicable for flush mounting in a boarding dash
4. ing voltage V tolerance 25 12 24 36 48 Current consumption max mA 50 35 35 25 EMC emission EN 55011 immunity EN 50082 2 in case of excess voltages that are above the approved EMC EMI protection we recommend a shielding from custom s side Vibration EN 60068 2 34 1g eff 10 500Hz 2 5h Shock EN 60068 2 27 30g 18ms 3 shocks Continuous shocks EN 60068 2 29 25g 6ms 1000 shocks Relay contact opens when reaching discharge voltage voltage free breaking capacity 12VDC 5A 24VDC 5A 36VDC 3A 48VDC 2A Signal inputs Minimum pulse duration 0 5 sec Display multi LED bar display 8 LEDs LC Display 6 digits 4 5mm Counting range hour counter up to 99999 9h service counter option up to 9999h Time divergence max 0 02 Ambience 30 C to 70 C max 95 humidity Protection class IP65 frontal Bauser GmbH amp Co KG J ulius Bauser Str D 72186 Empfingen Tel 07485 181 0 Fax 07485 181 16 e mail mail bauser control de Internet www bauser control de Edition 04 03 Rev 2 2
Download Pdf Manuals
Related Search