Operating Instructions for the metal
Contents
1. 15 in place Dismantle Spring cover 20 and take spring out 19 Take circlip 16 and washer 17 off Push knife pin 18 out of casting Take knife out of housing Attention do not exchange the spacing shims 15 Place the knife inside the housing feed shims in on one side and push knife pin 18 into housing up to the middle of the knife Feed the shims on the other of the knife Push knife pin in completely and secure washer 17 and circlip 16 again Assemble spring 19 and spring cover 20 Between the knife 11 and the jaws 10 should be some distance approximately 0 05 mm on each side Knife 11 must be placed tight in the head casting Adjustment for the play between the jaws a 0 1 0 15 mm If knife has contact with the jaws on both sides adjust with screws in the head casting lf a burr is on the material adjust the space between the knife and the jaws Replace jaws with a new set loosen 4 screws 8 take jaws 10 and pins 9 off assemble again and tighten with the screws Spare Parts List for DRACO Metal Shear AK 3010 AK 3013 AK 3017 Pos Order ltem Pc Pos Order ltem Pc no no no no 33010 Shearhead AK 3010 compl assembl 35 10300 Needle Bearing 2 1 43 48 51 52 33013 Shearhead AK 3013 compl assembl 36 BG10450 Cap for Needle Bearing Pos 35 36 1 1 43 48 51 52 33017 Shearhead AK 3017 compl assembl 1 43 48 51 52 48 13043 o Needle Bearing 1 88080 Screw 1 8312. 0038 Ball Bearing 1 8 33086 Cable 1 22 10077 Supporting roller in metal 1 99 31298 Power Akku Bxs 12 1 24 17900 Knife Pin Bushing 10mm e g 32 _ BG10004 Excentric Drive Shaft Pos 32 34 37 40 1 gt gt O 32 10004 _ Excentric Drive Shaft d O 33 10250 Ball bearing i i O 34 100005 Sleeve 2R O Max Draenert GmbH amp Co KG Electric Cordless Pneumatic Tools Machines Germany Phone 49 7153 8217 0 Fax 49 7153 8217 66 Factory Administration D 73777 Deizisau P O Box 1120 Manufacturing Shears D 73779 Deizisau Gutenbergstrasse 15 17 Factory Il Manufacturing D 73779 Deizisau Seewiesenweg 1 Roofing System Internet http www dracotools com e mail draenert dracotools com
3. Operating Instructions 1 Intended use This Power Tool is intended for industrial applications for cutting sheet metal maximum capacity is indicated in the Specifications for use with cutting jaws and cutting blades which are indicated in these operating instructions or recommended by DRACO 2 Initial Operation Observe the rated voltage The voltage of the power source must match that given on the nameplate of the machine Chargers for 230V can also be operated on 220 V power sources Switching ON and OFF Switching ON Slide the switch 93 forward Switching OFF Slide the switch 93 to the rear 2 The material to be cut must always be free of oil or grease Always place the machine flat on the work piece 3 Cut outs Drill a starting hole with a 12 14 mm diameter drill Circular cuts Always cut counter clockwise and from left to right 4 Do NOT cut sheet metal along welding points Do NOT cut multi layer sheets which exceed the maximum cutting capacity 5 Battery Change Before using the cordless tool charge a new or empty battery The full capacity is reached after charging the battery about 4 5 times Care and Maintenance Before working on machine disconnect from power supply by removing plug from socket Always keep the machine and the ventilation slots clean Oil the knife pin at regular intervals If the machine should happen to fail despite the care taken in manufacture and testing repair should b
4. e carried out by an authorised customer services agent for DRACO power tools CE Declaration of conformity We declare under our sole responsibility that this product is in conformity with the following standards EC 98 37 EC 93 68 EWG EC 04 108 EC or standardisation documents DIN EN ISO 12100 1 DIN EN ISO 12100 2 EN 50 144 EN 55 014 ZA Ae 7 A J E Max Draenert Insert the battery A Insert the battery from the back until it clicks into place Abb A Remove battery B Press both stop locks together take battery off see arrow 6 For inside cutting the shortest curve possible has a radius of 200 mm 8 If cutting a radius with the right hand cut from right to left The outside radius is unlimited 7 For cutting out curved or circular inside patterns a 14 mm 1 2 hole or a punched slot should be made to insert the centre cutter 8 If after cutting a small strip remains this can easily be trimmed off to the exact measurement without leaving a burr or any distortion of the material Just one side of the cordless tools can be used for cutting also e g along a marked line Lift the power tools out of the shavings while the motor is running Cut off longer shavings 9 Both knife and jaws can be sharpened After being sharpened or replaced the knife at it s lowest point should protrude the jaws by approximately 3 mm The knife should have approximately 0 05 mm 0 005 play on each sid
5. e of the jaws centring the cutter with spacing shims supplied 10 Every 200 operating ours have the cutting blade and cutting jaws sharpened at a specialist workshop 11 Ensure that the material to be cut is free of oil and grease Warranty DRACO tools carry a guarantee of 12 months from date of delivery Damage attributable to normal wear and tear overload or improper handling will be excluded from the guarantee e g blades knifes and jaws In case of complaint please send the machine undismantled to your dealer or the DRACO Service Centre for electric power tools Environnemental protection B Recycling raw materials instead of waste disposal Machine accessories and packaging should be sorted for environment friendly recycling Operating Instructions for the metal shears AK 3010 AK 3013 AK 3017 To avoid any disturbance please read the following instructions For your safety 1 2 1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed 2 The machine must not be used when damp and must not be operated in a wet environment 3 Always inspect cable and plug before using machine Only have damage repaired by a qualified professional Put the plug into the mains socket only when the machine is switched off 4 5 Always wears protective goggles protective g
6. loves and heavy duty shoes when working ej sW Do not carry the machine by the cable Always remove the plug from the power supply socket before carrying out any work on the machine when interrupting work and when not using the machine Always place the cable to the rear away from the machine Apply the machine to the sheet metal only when switched on Always provide for secure footing when working Firmly clamp the work piece if it dose not remain stationary from its own weight The knife should not rub on the jaws Possible danger of cutting tool breakage Do not exceed the maximum allowable material thickness especially when cutting over doublers folded joints or welded seams F For further notes on safety refer to enclosed sheet Technical Data DRACO metal shear type AK 3010 max thickness steel 400 N mm mm ga 1 0 19 stainl steel 600N mm2 mm ga 0 7 21 Stainl steel 800 N mm mm ga 0 4 25 non ferro 250 N mm mm ga 1 5 17 tightest radius mm 50 2 working speed m min 3 5 strokes min 1 1800 weight incl battery kg 2 1 AK 3013 AK 3017 1 3 18 1 6 17 1 0 19 1 3 18 0 7 21 1 0 19 2 0 14 2 5 12 100 4 140 52 3 5 3 5 1800 1800 2 1 2 1 SERVICE TIPS Before working on machine disconnect from power supply by removing plug from socket Wear protective glasses Optional oOo KR Ww Ph D One drop of oil between knife 11 and head casting 1 keeps the spacing shims
Download Pdf Manuals
Related Search