Installation and Operating Instructions
Contents
1. This object is used to call up scene 7 when a 0 telegram is received and to call up scene 8 when a 1 telegram is received The object can also be used to save the set lighting state in scene 7 or 8 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received 84 Call up a scene Scenes 9 10 1 bit CW This object is used to call up scene 9 when a 0 telegram is received and to call up scene 10 when a 1 telegram is received The object can also be used to save the set lighting state in scene 9 or 10 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received Call up a scene Scenes 11 12 This object is used to call up scene 11 when a 0 telegram is received and to call up scene 12 when a 1 telegram is received The object can also be used to save the set lighting state in scene 11 or 12 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received P Call up ascene Scenes 13 14 This object is used to call up scene 13 when a 0 telegram is received and to call up scene 14 when a 1 telegram is received The object can also be used to save the set lighting state in scene 13 or 14 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received Merten GmbH amp Co KG programming mode If programming mode is act2. DALI segment The value 0 means that no error occurred The value 1 means that a malfunction has occurred in at least one of the lamps in the segment 94 Error Error status total 1 bit CRT Electronic input unit malfunction This object is used for information about the error status related to electronic input unit malfunctions within the DALI segment The value 0 means that no error occurred The value 1 means that a malfunction has occurred in at least one of the electronic input units in the segment Merten GmbH amp Co KG Parameters For a better overview the parameters in the application are spread out over various pages The following parameters are available General page Edit Parameters 3 x Group 9 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 General Group 1 Group 2 Group 3 Group 4 Group 5 Group amp Group 7 Group 8 Sending condition of status object i ending on change Behaviour on bus voltage failure Recall and storage of by ibitobiects l scenes occures Behaviour on bus voltage recovery Sending condition failure object Light value on DALI and EIB failure Cancel Default Info Settings Send condition light status Only send on demand Send on change Here the send condition for the light status of the DALI groups 4 communication object of each group are set Behaviour on bus vol
3. If the red ERR LED is still ON after connecting the EIB fed with its EIB power supply and after download of the application program a short circuit within the DALI segment is the prob able error source refer Submenu SYSTEM TEST Please check the wiring of the DALI segment in such cases Merten GmbH amp Co KG 4 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Operation and Menu Structure The connected DALI segment can entirely be commissioned with the three programming buttons SCROLL Prg Set ESC Optional DALI parameters can also be set or changed with these buttons The usage is menu driven Depending on the current menu position up to two submenu levels can be accessed The currently selected menu item is shown in the display The user navigates within the menu with short pushes of the buttons the SCROLL button selects the next menu item within each level A short push on the Prg Set button selects the submenu if it exists The ESC button quits the current menu level and returns to the parent menu item Main Menu Level 1 The main menu is structured as follows a The product description and the firmware version are displayed This screen features a submenu that allows to select DALI CONTROL the display language SC 16 V 1 0 This screen features submenus which will reset all connected DALI ECGs and will start an automatic detection of connected d
4. The search process can require several minutes depending on the number of connected ECGs During the search process the number of new ECGs that are discovered is summa rized on the display Z m ECGs 1 After completion of the verification and of the search process the number of deleted and new ECGs are shown on the display deleted ECGs on the left new ECGs on the right By pushing the ESC button or by simply waiting SE NEY for more than 30 seconds the parent menu item is again activated ECGs 3 1 Merten GmbH amp Co KG 6 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Submenu GROUP ASSIGNMENT Level 2 and 3 GROUP ASSIGNMENT ECG Nr 12 GROUP ECG Nr 12 GROUP 1 A short push on the Prg Set key leads from level 1 menu GROUP ASSIGNMENT to a submenu allowing to assign ECGs to one of the 16 DALI groups Within the submenu it is possible to create new assignments for ECGs or to modify existing ones A short push on the SCROLL button navigates from one ECG to the next The first display line shows the number of the selected ECG The corresponding light will blink for as long as its ECG is selected This allows to easily iden tify which number is assigned to which light A long push of the Prg Set button switches the device to programming mode A short push on the SCROLL Button allows to select the group to which the ECG is to be assigned
5. by pushing the Prg Set button for more than 2 seconds Once the selected function of parameter is in programming mode an Arrow symbol appears in the display Once the programming mode is active the SCROLL button is used to change the setting or the parame ter value By pressing the Prg Set button with a short push again the programming mode is ended EXIT and SAVE The parameter is up dated to the selected value or the selected function is activated The ESC button quits the programming mode without saving Submenu DALI CONTROL Level 2 The level 1 menu DALI CONTROL leads to the submenu SPRACHE LANGUAGE by pressing the Prg Set key DALI CONTROL with a short push sc 16 V 1 0 The currently active language is displayed within the submenu By pressing the Prg Set button for more than 2 sec E onds the programming mode is activated The SCROLL button navigates through the available languages ae DEUTSCH ENGLISCH English FRANZ S Fran ais SPANISCH Espa ol SCHWEDISCH Svenska Press ing the Prg Set button with a short push this time the new language is activated and the display changes accord ingly The default language on shipment is GERMAN Submenu NEW INSTALLATION Level 2 A short push on the Prg Set key leads from level 1 menu NEW INSTALLATION to the submenu SEARCH ECG via NEW INSTALLATION P MODE A long push of the Prg Set button switches the device to programming mode Another push but a short
6. length for one entire DALI segment must not exceed 300m After connecting the DALI control wires the op tional external pushbuttons can be connected The binary inputs are passive meaning that an auxiliary 8 26VAC or 9 32V DC voltage is re quired to operate the switches It is now possible to connect the 110 240 VAC 50 60 Hz mains wires to the lower right connec tor block according to the printed schema The EIB bus cable is connected using the fea tured bus connector that is already inserted in the block when the device is shipped For proper insulation from the power block it is necessary to wrap the EIB control wires from the cable end right to the EIB connector with the shrink sleeve that is part of the package DALI ECG DALI ECG External External Power Supply Pushbuttons 8 26 VAC or 9 32 VDC S L D D B1 B1 B2 B2 L pwr aa ERR Scroll Prg Set ESC gt 2s DALI CONTROL SC 16 V 1 0 EIB LED Prog PE LN SHRINK SLEEVE EIB 110 240 VAC MAINS POWER After complete connection of the device and activation of the mains power the device will display its product name and the firmware ver sion The blinking green PWR light signals that the device is ready If the device is started without being connected to the EIB and as long as no corresponding EIB application program has been downloaded the red ERR LED is lit
7. that it is not The four characters following the scene number represent groups 1 through 4 the 12 characters on line two represent groups 5 through 16 A long push of the Prg Set button switches the device to programming mode A blinking cursor on the first X shows that Group 1 is currently selected A short push of the SCROLL button toggles between selected X and not se lected A short push of the Prg Set button moves the cursor to the next Group field which in turn can be se lected or not with the SCROLL button etc Once all 16 Groups have been moved through the configuration is saved and immediately active After completion of the last group this submenu is closed automatically and the de vice returns to the next higher menu item To avoid saving changes don t complete the line and use the ESC but ton instead or simply wait for more than 30 seconds Merten GmbH amp Co KG 7 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Submenu GROUP TEST Level 2 and 3 GROUP TEST GROUP 6 TEST GROUP 6 gt of f A short push on the Prg Set key leads from level 1 menu GROUP TEST to a submenu allowing to switch individual DALI Groups or all DALI Groups via broadcast at the same time for testing purposes A short push on the SCROLL button within the submenu allows to navigate from one group to the next The cur rently active group is shown on the first d
8. 0 Type of status object Switch status 1 bit Here the parameter settings are made for the light value set in Value status 0 100 the respective DALI group on receiving a 1 telegram i i Here you can set whether the status object should only provide Dimming time 5 seconds the ON OFF switch status or the value status 0 100 for the 10 seconds respective DALI group 15 seconds Recognisable error types No error status 20 seconds Only lamp malfunction Cancel Default Thi 30 seconds Only electronic input unit 40 seconds malfunction 60 seconds Lamp and electronic input unit Here the setting is made for the time it should take to dim from malfunctions 0 to 100 on receiving a dimming telegram dimming speed Here you can set for which malfunctions the error object of each T respective group provides an error status Minimum dimming value p group p The minimum dimming value is set here The setting 0 means that the dimmer can also be used to switch off the light You can always switch on the light using the dimmer Merten GmbH amp Co KG 4 4
9. 2 EN 61000 6 3 Environmental e Operating Temperature 0 C to 45 C Storage Temperature 25 C to 70 C e Rel Humidity non condensing 5 to 93 Certification KNX EIB registered CE Signage According to EMC recommendations domestic and commercial buildings low voltage recommendations Merten GmbH amp Co KG 2 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Location and Function of the Control and Display Elements The connectors as well as the KNX EIB programming button and LED are only accessible once the cover of the distribution panel removed The operation of the programming buttons SCROLL Prg Set ESC the control LEDs PWR and ERR as well as the menu display are ac cessible even with closed cover A5 A6 A7 A12 A13 A N Fd Z a Jo 4 A11 E y NO A D D B1 B1 B2 B 7 Z Pa A N RAS f a AQ E ERR 7 Scroll Prg Set ESC gt 2s A10 DALI CONTROL oC Lo Vele EIB LED Prog PE LN A8 i A1 A2 A3 A4 At the lower side of the casing the following connectors can be found left to right A1 EIB bus connector A2 EIB Programming LED A3 EIB Programming Button A4 Mains Connector At the upper side of the casing the following connectors can be found left to right Ad DALI connector AG Connector passive binary input 1 AT Connect
10. Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 The INSTABUS DALI gateway brings the lighting control specfic DALI Bus and the pluridisciplinary and cross functional EIB KNX bus together Cost effective DALI ECGs can therefore be seam lessly integrated into an overall EIB KNX architecture DALI instal M7 NINO lations can benefit from the vast range of EIB KNX user interfaces 9 90 o 79 2N sensors and building control devices available today The DALI gateway serves both as DALI Master device and power supply to all connected ECGs Up to 64 ECGs allocated to up to 16 different groups can be connected per single DALI gateway Additionally up ee to 16 lighting scenes can be created from the different groups The mn aas light intensities and failure warnings are available as status objects and can be visualized using any corresponding EIB KNX display device The commissioning of the DALI gateway allocation of DALI instabus EIB merten 6801 29 DALI Gateway REG K 1 16 64 A ECGs to the various groups is performed using the programming Bota buttons and the display directly on the device The setting of the KNX Ela different parameters and the programming of the scenes can also EIB LED Prog PE LN be perfomed with the buttons and the display or alternatively using 5 67 8 9 13 14 15 16 17 18 ETS Scenes that have already been programmed can subse La OO OO quently be ch
11. N VALUE is displayed The parameter value can be changed with a short push of the SCROLL button If no change is required don t use the SCROLL button A short push of the Prg Set button saves the parameter value and jumps to the next parameter of this group MIN VAL which can in turn be modified or not A short push again of the Prg Set button saves the parameter value and jumps to the next parameter of this group MAX VAL which can in turn be modified or not And finally another short push of the Prg Set button saves the parameter value and jumps to the next parameter of this group DURATION which can in turn be modified or not A short push of the Prg Set button saves the value and jumps again to the first pa rameter ON VALUE It is possible to escape back to the next higher menu with the ESC button or by simply wait ing for more than 30 seconds Submenu SCENE ASSIGNMENT Level 2 and 3 SCENE ASSIGNMENT SCENE01 XXXX XXXXXXXXXXXX n Q m Z m w A short push on the Prg Set key leads from level 1 menu SCENE ASSIGNMENT to a submenu allowing to associ ate DALI Groups to up to 16 DALI Scenes With a short push of the SCROLL button it is possible to navigate from one scene to the next The first display line shows the number of the currently selected scene Symbols show which of the 16 groups are associated with this scene An X at the corresponding location means that the group is part of the scene a means
12. Once the assignment completed a short push on the Prg Set button will confirm and save the selection For a new installation this task needs to be completed for each ECG that was discovered during the search process By pushing the ESC button or by simply waiting for more than 30 seconds the parent menu item is again activated Submenu GROUP PARAMETERS Level 2 and 3 GROUP PARAMETERS GROUP 01 PARAMETERS GROUP 12 ON VALUE 100 GROUP 12 MIN VAL 0 GROUP 12 MAX VAL 100 GROUP 12 DURATION 10s A short push on the Prg Set key leads from level 1 menu GROUP PARAMETERS to a submenu allowing to set all parameters of a DALI Group It is recommended to set the group parameters within ETS and only use this function for quick modification of individual settings Please note that each ETS download overwrites these manual settings A short push of the SCROLL button navigates from one group to the next The first display line indicates the current group number A long push of the Prg Set button switches the device to programming mode and the parameter type and its value are shown on the second display line The following parameters can be modified directly on the device Initial ON Value O to 100 in 5 steps Lower Dimming Limit MIN VAL 0 to 40 in 5 steps Upper Dimming Limit MAX VAL 50 to 100 in 5 steps e Dimming Duration for 0 100 5 sec to 60 sec Once the programming mode is active the first parameter O
13. Power Supply via the EIB Bus Operating Elements e Programming Button to toggle between normal and addressing mode 3 buttons SCROLL Prg Set ESC on display front to commission the device and set parameters Display Elements Red LED to indicate EIB KNX Normal Addressing Mode e Green PWR LED to signal device readiness blinks when in normal operation mode Red ERR LED to signal fault status e LC Display 2 lines with 12 characters each with menu for commissioning and setting of parameters Inputs e 2 X passive binary input for connection of conventional pushbutton or movement sensor 9 32VDC or 8 26VAC max wire length 15m DALI Bus e Connection of up to 64 ECGs complying to IEC 60926 DALI Voltage 18 21VDC short circuit proof It is not allowed to use other control devices DALI Master devices within the same line Connectors e EIB bus connector Mains Connector screw connector 3x 1 5mm single or threaded core DALI Bus screw connector 2x 1 5mm single or threaded core Binary input screw connector 2x 1 5mm single or threaded core Mechanical Data e Casing Plastic LEXAN UL 94 VO Measurements of casing Width 106mm Height 55mm Length 86mm e Weight 200 g e Mounting on 35mm DIN rail Electrical Safety Pollution Degree 2 Protection EN 60529 IP20 Protection Class IEC 1140 l e Overvoltage Category lI Bus SELV DC 24 V EMC Compliance Complies with EN 50090 2 2 EN 61000 6
14. an be switched and dimmed in 16 groups for each gateway Additionally up to 16 lightscenes can be programmed and retrieved at the individual groups Brightness values and error messages are available as status objects on the EIB and can be visualised using appropriate display units DALI commissioning assignment of the DALI electronic input units to the individual groups is carried out with the help of the integrated display and the control keys The setting of the individual group parameters and the assignment of the scenes can also be carried out using the device s control keys or alternatively directly in ETS Scenes that have already been programmed can be modified by the user at the device at all times In addition to the EIB and the DALI interfaces the device has two passive inputs for connecting conventional push buttons or movement detectors directly to the device Commissioning testing as well as operating the DALI devices via the passive binary inputs can also be carried out without connecting the EIB line e g building site operation As a REG K device 6 modules the DALI gateway is suitable for installation on DIN rails in standard sub distribution boards The bus is connected using a bus terminal Network DALI and push button cables are connected using screw terminals on the device The application program DaliControl 7303 1 0 is available for operating the device Merten GmbH amp Co KG Communication obje
15. anged at any time on the device Finally in addition to the EIB KNX and the DALI interface there are two binary inputs available on the device for connecting conventional switches pushbuttons or movement sensors This allows commissioning test and operation of the DALI ECGs without the connection of the device to the EIB KNX network The DALI gateway is a 6 units wide DIN Rail mounted device The EIB KNX connector is a standard EIB KNX BUS connector The DALI bus the mains power and the binary inputs are fixed using screw connectors Device Type and Accessories The following devices and accessories of this product group are available INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Package Contents The delivery package of the INSTABUS DALI gateway REG K 1 16 64 contains the following components e Device with connected bus connector o 1x shrink sleeve 1 2 x 2cm for supplementary insulation of the bus wires e Installation and Operating Instructions Application Programs Currently the following application programs are available for this device DaliControl 7303 1 0 Please refer to the application description for detailed information on the application program functionality Merten GmbH amp Co KG 1 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Technical Data Power Supplies e Mains Connector for 110 to 240 V 50 to 60Hz max 0 1A e Additional
16. arameters The object type changes depending on the parameter settings The requirement for sending the object can be adjusted 1 This object is used for information about the error status within a DALI group Whether only a lamp malfunction a malfunction of the electronic input unit or both types of malfunction result in an error status can be set in the parameters An object value of 0 means that no malfunction has occurred within the group A value of 1 means that at least one malfunction has been detected within the group The requirement for sending the object can be adjusted Like objects 0 to 4 for DALI group 1 objects 5 to 9 are assigned to DALI group 2 in the same way The same applies to objects 10 to 14 for DALI group 3 etc up to objects 75 to 79 for DALI group 16 1 4 merten Application description INSTABUS DALI gateway REG K 1 16 64 Art no 680129 DaliControl 7303 1 0 Objects 80 to 88 are required for retrieving and programming set lightscenes Whether scenes with 1 bit telegrams or 1 byte telegrams are retrieved can be set in the parameters Bear in mind that the assignment of the individual DALI groups to the various scenes at the device is carried out using the operating menu cf also operating and installation instructions If 1 bit scenes are used objects 80 to 88 are displayed Call up ascene Scenes 15 16 This object is used to call up scene 15 when a 0 telegram is received and to ca
17. button issues ON command e OFF pushbutton issues OFF command TOGGLE pushbutton toggles between ON and OFF e ON DIM short push on the button issues ON command long push dims up and issues a stop tele gram when pushbutton is released e OFF DIM short push on the button issues OFF command long push dims down and issues a stop telegram when pushbutton is released e TOG DIM short push toggles between ON and OFF long push dims up or down and issues a stop telegram when pushbutton is released Single Button Dimming e SCENE pushbutton invokes a scene Merten GmbH amp Co KG A long push on the Prg Set button switches the device to programming mode A short push on the SCROLL button allows to select the group or the scene with which the function is to be associated A short push on the Prg Set but ton confirms the selection and exits Pushing the ESC button or simply waiting for more than 30 seconds cancels the operation and leads back to the parent menu item 9 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 First Installation of a DALI Segment Once the wiring of the device has been completed according to the above instructions the DALI segment can be commissioned directly with the device independently of the EIB system As long as the EIB is not connected and application program is not loaded the red failure LED ERR will be lit but the commissioning can proceed nevert
18. cts A maximum of 95 communication objects are available for the communication of the device via the EIB In parts the objects are displayed or hidden depending on how the parameters are set The communication objects can be linked using 95 associations with 95 group addresses 5 objects are assigned to each of the 16 DALI groups The objects for group 1 are Object name The lamps assigned to DALI group 1 are switched to the set switch ON or switch OFF value using this object Whether switching is carried out immediately or dimmed to the final value when the object is received can be set in the parameters The dimming time can be adjusted independent of the dimming time when the dimming telegram is received Brighter Darker Dim group 1 The lamps assigned to DALI group 1 are dimmed up or down using this object The dimming time required to dim from 0 to 100 can be set in the parameters The lamps assigned to DALI group 1 are set to a brightness value using this object Whether the value is accepted immediately or dimmed to the final value when the object is received can be set in the parameters The dimming time can be adjusted independent of the dimming time when the dimming telegram is received Status group 1 1 bit CRT Status group 1 1 byte CRT The status of the lamps assigned to DALI group 1 can be provided using this object Whether a 1 bit status On Off or a 1 byte value status is transmitted can be set in the p
19. evices This is the preferred choice for a new installation INSTALLATION This screen features submenus that allow to resynchronize DALI ECGs after a post install adding or removing ECGs Aen E to a previously configured DALI gateway by starting an automatic detection and displaying the modified configura tion Within the submenus of this screen the detected ECGs can be allocated to the desired DALI groups GROUP ASSIGNMENTS aes Within the submenus of this screen the parameters of each group can be set and modified PARAMETERS ene The submenus of this screen allow to add DALI groups to DALI scenes ASSIGNMENTS eee The submenus of this screen allow to switch the entire DALI segment Broadcast or individual DALI groups for test TEST ing purposes igea This screen features submenus to invoke individual DALI scenes for testing purposes SCENES SYSTEM This screens leads to submenus that will display all existing system failures individually TEST FUNCTION The submenus of this screen allow to set the function of the binary input B1 INPUT B1 FUNCTION The submenus of this screen allow to set the function of the binary input B2 INPUT B2 Z m Merten GmbH amp Co KG 5 10 Installation and Operating Instructions merten INSTABUS DALI gateway REG K 1 16 64 Art no 680129 If a function is to be activated or a parameter to be changed within a given submenu it is necessary to switch to the so called programming mode
20. heless Here are the steps to follow 1 Testing For a first installation it is necessary to start by searching for all connected DALI ECGs using the menu NEW INSTALLATION Once all devices are discovered the display shows ESC right after the number of discovered ECGs to prompt the user to press the ESC button to exit this menu while giving him a chance to read or make a note of the number In a second step all discovered devices have to be individually assigned to DALI groups using the GROUP ASSIGNMENT menu The basic commissioning is completed with this second step Using the menu GROUP TEST individual groups can be switched ON and OFF for testing and quality control purposes Optional Settings If pushbuttons are connected to the inputs of the DALI gateway the menu FUNCTION INPUT B1 and B2 allow to select the de sired function for each input This allows basic operation of the DALI segment in case the EIB is not operational at that point e g for Construction Site Operation Subsequently the binary inputs can be used as a cost effective complement to the system for example to connect conventional presence or movement detectors or simply pushbuttons Finally it is possible to assign groups to scenes using the menu SCENE ASSIGNMENT This completes the commissioning of the DALI Segment The EIB programming and commissioning can be started from that point on using ETS and the DaliControl application program In case of claims go
21. isplay line A long push on the Prg Set button switches the device to programming mode A short push on the SCROLL button sets the desired action options gt on or gt off which then needs to be commited with a short push on the Prg Set button Pushing the ESC button or simply waiting for more than 30 seconds cancels the operation and leads back to the parent menu item Submenu TEST SCENES Level 2 and 3 TEST SCENES SCENE 2 TEST SCENE 2 gt invoke A short push on the Prg Set key leads from level 1 menu TEST SCENES to a submenu allowing to switch individual DALI scenes for testing purposes or to save current lighting settings to a given scene number A short push on the SCROLL button navigates from one scene to the next The currently active scene is shown on the first display line A long push on the Prg Set button switches the device to programming mode A short push on the SCROLL button sets the desired action options gt invoke or gt save scene which then needs to be committed with a short push on the Prg Set button Pushing the ESC button or simply waiting for more than 30 seconds cancels the operation and leads back to the parent menu item Submenu SYSTEM TEST Level 2 and 3 SYSTEM gal nN rh UO o D coe ct LAMP fault L 23 fault E 34 fault ral 5al H Q w Q A short push on the Prg Set key leads from level 1 menu SYSTEM TEST to a submenu allowing to view individual failure mes
22. itch ON value should be applied immediately or whether to dim up to the switch ON value on Edit Parameters E x receiving a 1 telegram Group 9 Group 10 Group 11 Group 12 Group 13 Group 14 Group 15 Group 16 Switch off behaviour Apply value immediately General Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 Dim to the value eee Here you can set whether to switch off or dim to the OFF value Dimming time 10 Seconds gt on receiving a 0 telegram ee eee 5 Z Behaviour on setting the Apply value immediately Maximum value for dimming value Dim to the value SE a SS ashe mena a Here you can set whether the light value should be applied Behavior when receiving Off immediately or whether to dim up or down to the value on Behavior when receiving value receiving a 1 byte telegram Dimming time for On Off set value 10 Seconds x Dimming time for On Off 1 0 seconds l Setting the value 15 seconds Type of status bic So second Type of recognized failures Lamp failures only y 30 seconds Hep 40 seconds 1 minute 2 minutes 3 minutes 4 minutes Settings 5 minutes Value on being switched on 0 10 minutes 5 15 minutes 10 20 minutes continued in steps of 5 Here you can set the time for dimming from 0 to 100 on 90 receiving an On Off or Set value telegram if the parameter 95 was set to Dim to the value 10
23. ivated the setting for the current lighting state in the respective scene is saved when one of the objects 80 to 87 is received After saving programming mode is deactivated and a 0 telegram is sent back to object 88 The programming mode is automatically closed 60 seconds after receiving a 1 telegram at object 88 After that the reception of one of the telegrams 80 to 87 is once more interpreted as retrieving a scene If 8 bit scenes are used then only object 88 is displayed Obj Funcion Object name 88 Call up save Scenes 1 16 1 byte CW scenes This object is used to call up the respective scene from scenes 1 to 16 when a telegram is received with a value between 0 and 15 If the uppermost bit is also set meaning a value from 128 to 143 the set lighting state is saved in the respective scene Call up Save Scene 1 0 128 Scene 2 1 129 Scene 3 2 130 Scene 4 3 131 Scene 5 4 132 Scene 6 5 133 Scene 7 6 134 Scene 8 7 135 Scene 9 8 136 Scene 10 9 137 Scene 11 10 138 Scene 12 11 139 Scene 13 12 140 Scene 14 13 141 Scene 15 14 142 Scene 16 15 143 2 4 merten Application description INSTABUS DALI gateway REG K 1 16 64 Art no 680129 DaliControl 7303 1 0 Objects 89 and 90 can be used to make the signal of the voltage free push button input available also to the EIB The assignment of the push button function is carried out at the device or by using the operating menu cf also operating and i
24. ll up scene 16 when a 1 telegram is received The object can also be used to save the set lighting state in scene 15 or 16 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received Obj Funcion Object name Call up a scene Scenes 1 2 88 Programming Save scenes 1 bit CWT mode After receiving a 1 telegram via this object the device is set to This object is used to call up scene 1 when a 0 telegram is received and to call up scene 2 when a 1 telegram is received The object can also be used to save the set lighting state in scene 1 or 2 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received 81 Call up a scene Scenes 3 4 1 bit CW This object is used to call up scene 3 when a 0 telegram is received and to call up scene 4 when a 1 telegram is received The object can also be used to save the set lighting state in scene 3 or 4 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received Call up a scene Scenes 5 6 This object is used to call up scene 5 when a 0 telegram is received and to call up scene 6 when a 1 telegram is received The object can also be used to save the set lighting state in scene 5 or 6 For this purpose the programming mode object no 88 must be set to 1 before a telegram is received Call up a scene Scenes 7 8
25. nstallation instructions Bear in mind that even when setting parameters for the push button as a dimming push button for DALI groups for the EIB only the switch object short operation of the button is available When setting parameters for the push button for calling up DALI scenes the corresponding object has no function Object name This object is used to make a switch signal available depending on the assigned push button function of voltage free input 1 Switch input 2 This object is used to make a switch signal available depending on the assigned push button function of voltage free input 2 Objects 91 to 94 are used for information about fault conditions within the entire DALI segment The objects are always sent when changes occur They can however also be retrieved The following complete fault objects are available Function Objectname Type This object is used for information about the error status of the DALI segment independent of the error type The value 0 means that no error occurred The value 1 means that there is an error in the segment Error status DALI 1 bit CRT bus This object is used for information about the error status of the DALI short circuit The value 0 means that no error occurred The value 1 means that a DALI short circuit has occurred Error status total 1 bit CRT Lamp malfunction This object is used for information about the error status regarding lamp malfunctions within the
26. ods should be returned to our Service Center Merten GmbH amp Co KG Losungen fur intelligente Gebaude Service Center Fritz Kotz Strakte 8 Industriegebiet Bomig West D 51674 Wiehl Telefon 49 2261 702 204 Telefax 49 2261 702 136 E Mail servicecenter merten de Internet www merten de For technical questions please contact our InfoLine Phone Fax E Mail 49 1805 212581 oder 49 800 63783640 49 1805 212582 oder 49 800 63783630 infoline merten de kostenpflichtig fee required Merten GmbH amp Co KG 10 10 merten Application description INSTABUS DALI gateway REG K 1 16 64 Art no 680129 DaliControl 7303 1 0 Using the application program Application program DaliControl 7303 1 0 1 3 Interfaces Gateways Program name Product family Product type 1 3 13 DALI gateway Manufacturer Merten suitable for Product name INSTABUS DALI gateway REG K 1 16 64 Art no 680129 Function description General information The DALI gateway connects the EIB installation bus which covers all utilities to the DALI bus which is designed solely for lighting control Cost effective digital electronic input units with DALI interface can therefore be integrated into an EIB complete system in the form of a subsystem and operated by a wide range of available EIB devices The DALI gateway is used as DALI master and power supply for the connected electronic input units Up to 64 electronic input units c
27. one this time starts the initialisation and search processes First all ECGs connected to this DALI Segment are reset auto on matically all previously assigned groups and parameters are deleted Secondly all ECGs are searched for by their randomly generated long address and identified in ascending order The search process can require several minutes depending on the number of connected ECGs After completion of ee T the search process the number of discovered ECGs is shown on the display By pushing the ESC button or by 2 simply waiting for more than 30 seconds the parent menu item is again activated Submenu POST INSTALLATION Level 2 A short push on the Prg Set key leads from level 1 menu POST INSTALLATION to the submenu SEARCH ECG via INSTALLATION P MODE A long push of the Prg Set button switches the device to programming mode Another push but a short one this time starts the verification and search process The connected ECGs are searched for by their long addresses ae ate The result is compared with the previous configuration If ECGs have been removed from the DALI Segment their corresponding entries and settings are automatically deleted from the DALI gateway During the verification proc ess the number of deleted ECGs is summarized on the display tu O Wn E He gees The Gateway then searches for new ECGs within the DALI Segment New ECGs are automatically reset and all previously assigned parameters are deleted
28. or passive binary input 2 On the device front the following elements can be found A8 Display 2x12 chars for DALI Commissioning A9 SCROLL button A10 Prg Set button A11 ESC button A12 Operating LED PWR A13 Failure LED ERR The signage of the connectors on the casing is to be followed at all times Installation Notices and Warnings e Life Hazard through Electrical Shock e The device must only be installed and commissioned by qualified Electricians e The current country specific safety and accident prevention rules and regulations as well as the EIB guidelines must be respected at all times e The device is destined for fixed mounting in dry interior locations e When connecting the mains wires the mains power must be switched off e The device must not be opened Defectuous devices must be returned to the manufacturer Merten GmbH amp Co KG 3 10 Installation and Operating Instructions INSTABUS DALI gateway REG K 1 16 64 merten Art no 680129 Mounting and Connection The INSTABUS DALI gateway REG K 1 16 64 is designed to be mounted within distribution panels equipped with 35mm DIN rails After simply snapping the device onto the rail the DALI bus should be connected first The DALI Control wires can be part of a 5 stranded cable also carrying the ECG power accroding to IEC90929 the base insulation is sufficient However each wire must be clearly marked and reliably identified The maximum cable
29. sages It is clearly shown on the display if there are failures or not The following failure types are recognized and shown on the display and also signaled by the red failure LED ERR Short circuit on the DALI bus Lamp failure with indication of the ECG number ECG failure with indication of the ECG number EIB Bus not present A short circuit on the DALI bus is a failure that prevents the device from recognizing any other failure that may be present By contrast all other failure types are detected simultaneously With a short push on the SCROLL button it is possible to navigate from one failure message to the next Lamp and ECG failures show the ECG number so that the error can be located immediately within the group Pushing the ESC button or simply waiting for more than 30 seconds leads back to the parent menu item Merten GmbH amp Co KG 8 10 INSTABUS DALI gateway REG K 1 16 64 Installation and Operating Instructions merten Art no 680129 Submenu FUNCTION INPUT B1 Level 2 and 3 FUNCTION INPUT Bl TOG DIM INPUT Bl TOG DIM GROUP ALL TOG DIM GROUP 07 A short push on the Prg Set key leads from level 1 menu FUNCTION INPUT B1 to a submenu allowing to select the function of the conventional pushbutton or presence detector connected to the binary input B1 A short push on the SCROLL button navigates from one function to the next The first display line shows the se lected function The following f
30. tage No change failure Switch to error value Switch off Here you can set which lighting condition should be set in the case of an EIB bus voltage failure Behaviour on bus voltage No change recovery Switch to error value Switch off Here you can set which lighting condition should be set on EIB bus voltage recovery Send condition Only send on demand error status Send on change Here the send condition for the error status of the DALI groups 5 communication object of each group are set The entire error statistics objects no 91 to 94 are always only sent on change Light value on DALI and EIB 0 errors 5 10 continued in steps of 5 90 95 100 Here you can set which light value is to be set in the case of a DALI or EIB fault 3 4 merten Application description INSTABUS DALI gateway REG K 1 16 64 Art no 680129 DaliControl 7303 1 0 The scenes are called up using 1 bit objects Minimum dimming value 50 and saved using 1 byte objects 55 60 Here you can set whether the scenes are called up and saved continued in steps of 5 using 1 bit or 1 byte objects The respective communication 90 objects are displayed depending on the setting 95 100 The maximum dimming value is set here For each group only one page is available for setting the group Switching on behaviour Apply value immediately specific parameters Dim to the value Groups 1 16 Here you can set whether the sw
31. unctions are available ON pushbutton issues ON command e OFF pushbutton issues OFF command e TOGGLE pushbutton toggles between ON and OFF e ON DIM short push on the button issues ON command long push dims up and issues a stop tele gram when pushbutton is released e OFF DIM short push on the button issues OFF command long push dims down and issues a stop telegram when pushbutton is released e TOG DIM short push toggles between ON and OFF long push dims up or down and issues a stop telegram when pushbutton is released Single Button Dimming e SCENE pushbutton invokes a scene A long push on the Prg Set button switches the device to programming mode A short push on the SCROLL button allows to select the group or the scene with which the function is to be associated A short push on the Prg Set but ton confirms the selection and exits Pushing the ESC button or simply waiting for more than 30 seconds cancels the operation and leads back to the parent menu item Submenu FUNCTION INPUT B2 Level 2 and 3 A short push on the Prg Set key leads from level 1 menu FUNCTION INPUT B2 to a submenu allowing to select FUNCTION INPUT B2 the function of the conventional pushbutton or presence detector connected to the binary input B2 A short push on the SCROLL button navigates from one function to the next The first display line shows the se lected function The following functions are available e ON push
Download Pdf Manuals
Related Search