Operating Instructions Operating Instructions for the metal
Contents
1. 11 must be placed tight in the head casting 12 Adjustment for the play between the jaws a 0 1 0 15 mm Max Draenert GmbH amp Co KG Electric Cordless Pneumatic Tools Machines Germany Factory Administration D 73777 Deizisau P O Box 1120 Phone 49 7153 8217 0 Manufacturing Shears D 73779 Deizisau Gutenbergstrasse 15 17 Fax 49 7153 8217 66 Factory Il Manufacturing D 73779 Deizisau Seewiesenweg 1 Optional Roofing System 13 If knife has contact with the jaws on both sides adjust with screws in the head casting lf a burr is on the material adjust the space between the knife and the jaws Internet http www dracotools com e mail draenert dracotools com 14 Replace jaws with a new set loosen 4 screws 8 take jaws 10 and pins 9 off assemble again and tighten with the screws2. Operating Instructions 1 Intended use This Power Tool is intended for industrial applications for cutting sheet metal maximum capacity is indicated in the Specifications for use with cutting jaws and cutting blades which are indicated in these operating instructions or recommended by DRACO 2 Initial Operation Observe the rated voltage The voltage of the power source must match that given on the nameplate of the machine Chrgers for 230V can also be operated on 220 V power sources Switching ON and OFF Switching ON Slide the switch 93 forward Switching OFF Slide the switch 93 to the rear 1 The material to be cut must always be free of oil or grease Always place the machine flat on the work piece 2 Cut outs Drill a starting hole with a 12 14 mm diameter drill Circular cuts Always cut counter clockwise and from left to right 3 Do NOT cut sheet metal along welding points Do NOT cut multi layer sheets which exceed the maximum cutting capacity 4 Battery Change Before using the cordless tool charge a new or empty battery The full capacity is reached after charging the battery about 4 5 times Care and Maintenance Before working on machine disconnect from power supply by removing plug from socket Always keep the machine and the ventilation slots clean Oil the knife pin at regular intervals If the machine should happen to fail despite the care taken in manufacture and testing repair should be car
3. Pc Pos Item Pc 18041 Pinion 20 teeth 81243 Spring washer o O B Motor Cover 84 OA Motor Cover 8 8087 wih 16 81275 Circlip 8933089 Motor cpl Pos 83 88 SERVICE TIPS Before working on machine disconnect from power 1 One drop of oil between knife 11 and head casting 1 keeps the spacing supply by removing plug from socket shims 15 in place 20 12300 SprngCover 7 94 33094 Switch pad Pe Pe rete Dismantle Spring cover 20 and take spring out 19 Take citclip 16 and washer 17 off Push knife pin 18 out of casting 32 BG33018 Driveshaft Pos340840 OCC O O O SSS y OoOO TEKS KATE O OUSIDE 32 BG35556 Eccentric Shaft Pos 32 33 343740 IOO O OOOO OoOO OoOo oOoOoO CO B2 35556 EcoentrioShat O oS oS S OSO Attention do not exchange the spacing shims 15 32 10004 Excenrio Drive Shat DOSO OOOO 7 Place the knife inside the housing feed shims in on one side and push knife pin eee e 18 into housing up to the middle of the knife 8 Feed the shims on the other of the knife Ordering spare parts please mention order and item number 9 Push knife pin in completely and secure washer 17 and circlip 16 again 10 Assemble spring 19 and spring cover 20 NINI OO OT NINI h h l ek ek AOUN h l gt 11 Between the knife 11 and the jaws 10 should be some distance approximately 0 05 mm on each side Knife
4. eavy duty shoes when working LS slit Do not carry the machine by the cable Always remove the plug from the power supply socket before carrying out any work on the machine when interrupting work and when not using the machine Always place the cable to the rear away from the machine Apply the machine to the sheet metal only when switched on Always provide for secure footing when working Firmly clamp the work piece if it dose not remain stationary from its own weight The knife should not rub on the jaws Possible danger of cutting tool breakage Do not exceed the maximum allowable material thickness especially when cutting over doublers folded joints or welded seams F For further notes on safety refer to enclosed sheet Technical Data DRACO metal shears AK 3520 AK 3514 2 AK 3514 7R_ AK 3515 ___ Art no 35201 351421 351471 35151 max cutting capacity steel 400 Nimm mm 7 H7 7 H7 13 3 M3 stainless steel 600 N mm mm 13 stainless steel_800 N mm mm 4 0 1 0 10 J10 non ferro 250 N mm mm 25 25 25 25 tightest radius working speed strokes spiral ducting Pittsburgh seam mesh and wire Eave AK3514 2 AK3514 2 AK3514 2 AK3514 2 N N g ASN ARN Nish S ASS A ii SAAN S AAN K Inside cut outs Formed parts cable trays AK3514 7R AK3520 Exploded view DRACO Ak Serie Spare Parts List for DRACO Metal Shears AK3514 2 AK3514 7R AK3520 AK3515 Pos Item
5. g the cutter with spacing shims supplied 9 Every 200 operating ours have the cutting blade and cutting jaws sharpened at a specialist workshop 10 Ensure that the material to be cut is free of oil and grease Warranty DRACO tools carry a guarantee of 12 months from date of delivery Damage attributable to normal wear and tear overload or improper handling will be excluded from the guarantee e g blades knifes and jaws In case of complaint please send the machine undismantled to your dealer or the DRACO Service Centre for electric power tools Environnemental protection Recycling raw materials instead of waste disposal Machine accessories and packaging should be sorted for environment friendly recycling CU Operating Instructions for the metal shears AK3514 2 AK3514 7R AK3520 AK3515 To avoid any disturbance please read the following instructions For your safety 1 2 3 Sx 1 Safe operation of this machine is possible only when the operating instructions and the safety precautions are read completely and the instructions contained therein are strictly observed 2 The machine must not be used when damp and must not be operated in a wet environment 3 Always inspect cable and plug before using machine Only have damage repaired by a qualified professional Put the plug into the mains socket only when the machine is switched off 4 5 Always wears protective goggles protective gloves and h
6. ried out by an authorised customer services agent for DRACO power tools CE Declaration of conformity We declare under our sole responsibility that this product is in conformity with the following standards EC 98 37 EC 93 68 EWG EC 04 108 EC or standardisation documents DIN EN ISO 12100 1 DIN EN ISO 12100 2 EN 50 144 EN 55 014 iy C 09 Max Draenert Insert the battery A Insert the battery from the back until it clicks into place Remove battery B Press both stop locks together take battery off see arrow 5 For inside cutting the shortest curve possible has a radius of 200 mm 8 If cutting a radius with the right hand cut from right to left The outside radius is unlimited 6 For cutting out curved or circular inside patterns a 14 mm 1 2 hole or a punched slot should be made to insert the centre cutter 7 If after cutting a small strip remains this can easily be trimmed off to the exact measurement without leaving a burr or any distortion of the material Just one side of the cordless tools can be used for cutting also e g along a marked line Lift the power tools out of the shavings while the motor is running Cut off longer shavings 8 Both knife and jaws can be sharpened After being sharpened or replaced the knife at it s lowest point should protrude the jaws by approximately 3 mm The knife should have approximately 0 05 mm 0 005 play on each side of the jaws centrin
Download Pdf Manuals
Related Search