Automatic Banding Machine Operating instructions BA 40/800
Contents
1. FHEMA Harald Hinderer Maschinenbau Setting up the banding machine with floor rack Fasten the castor break at the front of the floor rack Remove existing transport locks Place the banding machine on the floor rack so that the of the banding machine fit into the recesses of the Electric connection of banding machine to floor rack Plug the power cord of the banding machine into the socket of the floor rack Connect the power cord of the floor rack to a power outlet 230 V 50 Hz 16 A Switch on main switch of the floor rack Switch on main switch at the back of the banding machine If required plug in the foot actuator at the back of the banding machine and tighten the plug with the screw See page 7 for the operation Page 10 06 11 FHIMA Harald Hinderer Maschinenbau Loading paper when operated with floor rack Place the paper roll on the roll mount see figure for running direction Feed the paper around the guiding rolls at the control lever as shown in the figure Feed the paper through the clamp mechanism Feed the paper through the rack opening into the banding machine See page 6 for loading the paper band into the banding machine BA30 14 06 11 Page 11 FHMA Harald Hinderer Maschinenbau Page 12 BASO 13 Lubricating intervals In order to ensure a long service life of the machine it is necessar2. Operating instructions BA 40 800 Automatic Banding Machine FRHEINMA Harald Hinderer Maschinenbau 06 11 EC Declaration of Conformity in accordance with EC Machinery Directive 89 392 EEC Appendix II A The design of the machine of the make Automatic banding machine type BA 40 800 was developed designed and manufactured in accordance with the EC Directive 89 392 EEC by HIMA Harald Hinderer Maschinenbau Bruhlstrasse 22 73635 Rudersberg Germany The following harmonised standard are applied 89 392 EEC EN 292 EN 55014 EN 61000 3 2 EN 55104 The following national standards guidelines and specifications are applied 9 GSGV German ordinance on machinery safety A complete technical documentation exists in accordance with the directives and guidelines The operating instructions belonging to the machine are available Rudersberg Harald Hinderer Owner of HIMA Harald Hinderer Maschinenbau Information about the signatory FHEMA Harald Hinderer Maschinenbau Contents Description of features Technical specifications Power supply General instructions Setting up place of operation Loading the paper Adjusting product stops Setting length of band loop Putting into operation Hand operated single stroke mode Foot operated single stroke mode Automatic operation mode Adjusting the band tension Troubleshooting Setting up the banding machine with floor rack Electric conn
3. any chemical detergents away from the operating elements and the nameplate E 06 11 HIMA SERVICE Phone 0049 7183 307700 BA30 04 BA30 05 BA30 06 Page 5 FHEMA Harald Hinderer Maschinenbau N 4 N UL Wk S K BA30 07 Observe the band running direction BA30 08 Page 6 Setting up place of operation Caution Please observe the following in order to ensure a proper functioning of the machine 1 Place the banding machine BA 40 800 by HIMA on a secure and sturdy stand which is secured against tilting The stand must be non combustible 2 When setting up the machine make sure that there is adequate space around the machine and the ventilation slots for proper ventilation to avoid excessive heat reduces lifetime of electrical components Clean the ventilation slots from time to time from dust and dirt deposits Loading paper Coated paper or plastic film To load the roll into the roll compartment open the front door 1 and the compartment cover 2 and mount the roll Unwind a small portion of the band from the roll and close the compartment cover 2 Turn the eccentric lever 3 clockwise to an upright position pull the lateral band catch 4 against the spring force and turn it to the left Insert the band between the pressure rollers 5 and the guiding rollers 6 below the pin Turn the eccentric lever 3 counter clockwise back to the locking positio
4. 0 7700 Fax 0049 7183 30 77 01 E Mail hima maschinenbau t online de Internet www hima maschinenbau de
5. ding machine of the type BA 40 800 manufactured by HIMA is easy to operate but nevertheless requires pru dence The persons operating the machine shall be familiar with its operation and limits The following instructions must be observed Please read the operating instructions carefully prior to using the banding machine and use the machine only in the proper way described in these operating instructions Caution Persons not instructed in the operation shall not use the machine Please make sure that the designated opera ting staff has been instructed properly Do not operate the machine if it has been damaged during transportation or during use This applies in parti cular to damages of the appliance connector A with the main switch B the remote operation socket C or the operating elements D on the front The machine shall be serviced or repaired only by specialised persons HIMA customer service Do not repair the machine yourself warranty will become void In case of dama ges please contact the customer service immediately Putting into initial operation Remove all protective foils Remove any parts on or inside the machine or in the immediate vecinity of the machine Do not stick advertising stickers paper etc to the machine Danger of electrical shock Do not clean the outer case of the machine with a drip ping wet cloth Use a dry cloth The same applies to the electrical operating elements D Keep
6. e Load the items to be banded onto the machine table The start button 19 will flash Press the start button or the foot actuator the foot actuator must be connected to the remote operation socket located at the back of the machine The items will be banded 06 11 Page 7 FHMA Harald Hinderer Maschinenbau BA30 12 Page 8 Adjusting the band tension Turn the knob 20 into the direction to reduce the band tension and into the direction to increase it Automatic operation mode Turn on the main switch 17 at the back of the machine Press the On Off button 18 at the control panel The On Off button will flash heating will take 2 3 minutes Wait for the On Off button to show permanently Press the automatic mode button 19 and the button will show perma nently The machine is now ready for use Load the items to be banded onto the machine table and the banding process will start Troubleshooting Banding machine does not return to basic setting paper cannot be loaded Switch the machine off and on again with the main switch Press the On Off button at the control panel the machine will return to the basic setting and be ready for use Band is not sealed The sealing head does not heat faulty heating cartridge faulty thermo regulator Contact the customer service Paper is not clamped The band is not clamped check the entire paper path load band again if need be Banding mac
7. ection of banding machine to floor rack Loading paper when operated with floor rack Lubricating intervals Warranty Warranty card 06 11 BEE BD gt E PAliviA Harald Hinderer Maschinenbau BA30 02 BA30 03 Page 4 Description of features BA 40 800 The banding machine BA 40 800 by HIMA applies paper bands automatically where the paper is unwinded from a paper roll When the paper roll is loaded and the start button is pressed a band is pulled tight around the product to be banded sealed and cut off When removing the banded pro duct a new loop is formed instantly preparing the machine for a new work cycle Technical specifications Output up to 25 cycles min Width of banded product 30 310mm Stack height 3 220 mm Triggering of cycle manual start button foot actuator automatic mode button Dimensions 540 L x 350 W x 220 H mm Power supply 230 V 50 Hz 200 W Weight 32 kg Power supply Plug the supplied power cord into the appliance connector at the back of the machine and connect the other end to a sui table power outlet 230 V 16 A Caution Make sure the selected power outlet is appropriately fused 16A Otherwise there is the risk of fire in case of overload The supplied power cord shall be modified length plug etc by authorised specialists only 06 11 FHEMA Harald Hinderer Maschinenbau General instructions The ban
8. hine cannot be switched on Check power supply If power supply is faultless and machi ne cannot be operated contact the customer service 06 11 FHEMA Harald Hinderer Maschinenbau Banding machine cannot be switched on at the control panel Check whether the light of the main switch at the back is on If so the control panel is faulty please contact customer ser vice Banding machine can be switched on but does not start Check whether the front door protective contact is engaged properly Open the front door and close it with power Ifthe banding machine still cannot be started contact the custo mer service Banding machine switched off in the middle of a work cycle and does not return to basic setting Switch the machine off and on again with the main switch Press the On Off button at the control panel the machine will return to the basic setting and be ready for use Banding machine stopped in the middle of a work cycle Switch off main switch and check all flexible parts for easy running Remove possible obstructions and ensure that parts are running smoothly Check power supply and make sure that the front door protective contact is engaged properly Caution If the listed actions of remedy do not solve the respec tive problem please contact the HIMA customer service Do not attempt to repair the machine mechanical or electronic parts etc yourself as this will void the war ranty 06 11 Page 9
9. n Turn the lateral band catch 4 to the right until it snaps into place Form a loop between the two band guides 7 8 and insert the end of the band between the spring steel guide 9 and the clamping unit 10 Close the front door Caution In order to avoid damages to the machine use bands by HIMA exclusively terms of warranty 06 11 FHEMA Harald Hinderer Maschinenbau Adjusting product stops Loosen the knurled screws of the band guides 7 8 and set the desired loop width approx 1 3 longer than the product width Fix the guides by tightening the knurled screws 11 again Caution Adjust the guides in a way that the hole of the photoel ectric barrier 12 is located near the center of the pro duct Loosen the knurled screws to set the product stops BA30 09 13 14 to the desired product length and tighten the knurled screws again to fix the stops Setting length of band loop The knob 15 to adjust the length is located on the operating PCB which is mounted to a bracket 16 in the machine Turn the knob 15 into the direction to reduce the length of the band loop and into the direction to increase it Single stroke operation mode Turn on the main switch 17 at the back of the machine Press the On Off button 18 at the control panel the On Off button will flash heating will take 2 3 minutes Wait for the On Off button to show permanently The machine is now ready for us
10. y to lubricate some parts Please use commercial white or fine oil for lubricating Please observe the following lubricating intervals 1 monthly 2 daily 3 monthly 4 daily In case of heavy dirt development spots 2 4 should be lubricated twice a day 06 11 FHMA Harald Hinderer Maschinenbau WARRANTY CARD TYPE BA 40 X BA 40 800 Machine Delivery date Customer Address evi nr BRUHLSTRASSE 22 73635 RUDERSBERG PHONE 0049 7183 30 7700 FAX 0049 71 83 3077 01 Harald Hinderer Maschinenbau Warranty HIMA Harald Hinderer Maschinenbau issues a six month warranty for the machine The warranty covers material or manufacturing faults which occur during normal load The war ranty does not cover damages of parts caused by improper use wrong operation or wilful intervention into the machine The warranty excludes secondary damages of any type The warranty starts with the day of delivery delivery note date Warranty procedure 1 Enclose warranty card The machine number on the warranty card must be identical to the number on the machine nameplate 2 Enclose copy of invoice 3 Clean the machine prior to packaging 4 Make sure the packaging is safe use original packaging 5 Enclose a short description of the error 06 11 Page 13 FHIMA Harald Hinderer Maschinenbau Banding machines Production Sales gt Service Br hlstrasse 22 D 73635 Rudersberg Phone 0049 7183 3
Download Pdf Manuals
Related Search