Operating Instructions Attachment with Radio Control
Contents
1. Ref no 5232 F 0202 FS 7 Technical data Power supply from flush mounting insert Receive frequency 433 42 MHz ASK Number of radio channels 30 Switch over time for directional changes approx 1s Temperature range approx 0 C 55 C Technical specifications subject to change 8 Guarentee We accept the guarantee in accordance with the corresponding legal provisions Please return the unit postage paid to our central service department giving a brief description of the fault ALBRECHT JUNG GMBH amp CO KG Service Center Kupferstr 17 19 D 44532 Lunen Service Line 49 23 55 80 65 51 Telefax 49 23 55 80 61 89 E Mail mail vka jung de General equipment Service Line 49 23 55 80 65 55 Telefax 49 23 55 80 62 55 E Mail mail vkm jung de KNX equipment Service Line 49 23 55 80 65 56 Telefax 49 23 55 80 62 55 E Mail mail vkKm jung de C The C Sign is a free trade sign addressed exclusively to the authorities and does not include any warranty of any properties2. input Important The sensor line carries safety extra low voltage SELV Please observe the installation instructions of VDE 0100 For the description installation and connection of the insert please refer to the operating instructions manual of the motor control insert Sensor concealed wiring procedure Fig F 1 Choose a cable type suitable for the installation of the sensor wiring Recommended cable J Y ST Y 2x2x0 6 mm 2 Pass the individual wires of the sensor cable through the insulating sleeving supplied with the device Then lead the wires together with the sleeving through opening of the insert 3 Run the wiring through duct to connecting terminal The sleeving must insulate the full length of the single wires from the outer jacket to the connecting terminal 4 Press the terminal block into the insert as shown in Fig F JUNG Attachment with Radio Control Receiver Ref no 5232 F 5232 FS Sensor surface wiring procedure Fig G 1 Pass the sensor cable behind the mounting frame between wall and frame through opening into the duct of the insert 2 Lead the line through the duct down to terminal connector The line must be laid properly in the duct and run straight to the terminals without forming any loops in the 230 V AC connecting compartment 3 Press the terminal block into the insert as shown in Fig G Programming a Radio Transmitter In the programming
3. mode the sensitivity of a radio receiver is reduced to approx 5 m Therefore the distance between the attachment with radio control receiver and the radio transmitter to be programmed should be between 0 5 m and 5 m Procedure 1 Press the full surface area of the cover for about 4 s Fig H to get into the programming mode This will activate the programming mode for about 1 min and be indicated by a sequence of tone pulses Fig I JUNG Attachment with Radio Control Receiver Ref no 5232 F 5232 FS 2 Start the selected radio transmitter to send a data telegram Fig J refer to the Radio Transmitter operating instructions manual Programming a channel Press the channel key for more than 1 second Programming a lightscape key Press the lightscape key for more than 3 seconds 3 The radio pushbutton will confirm storage by a continuous tone Fig K 4 You will automatically exit the programming mode after about 1 min or by shortly pressing one of the rockers of the attachment Note If all of the 30 memory locations are occupied you will have to delete one of the transmitters already stored to program another one Deleting a Radio Transmitter You can delete a radio transmitter already stored by reprogramming the same You must delete all channels and lightscape keys individually Successful deleting will be confirmed by a tone having a higher pulse frequency than for programming F
4. with Radio Control Receiver Ref no 5232 F 5232 FS The potentiometer has been factory set to about 10 000 lux position as shown in Fig C Glass breakage sensor The glass breakage sensor Fig D offers protection against the weather in the event of a broken window pane If a pane is broken the blind shutter will move to its lowermost position You can use the amp key to reset a glass breakage message This will make the blind shutter move up Note Do not use the glass breakage sensor in conjunction with the wind sensor If the glass breakage sensor has tripped the wind protection function will be disabled through the extension input ie Up with the blind shutter remaining shut Installation You can place into operation the attachment only in conjunction with a motor control insert The operating instructions manual of the insert describes how to connect and install the latter Procedure 1 Install the motor control insert into a flush mounted box deep box recommended with the connecting terminals of the insert at the bottom 2 Plug radio pushbutton onto the insert together with frame when the mains voltage is disconnected Note The distance to electrical loads e g blind shutter motor hifi and TV systems must be at least 0 5 m JUNG Attachment with Radio Control Receiver Ref no 5232 F 5232 FS Connecting the sensors only for attachment with sensor
5. JUNG Attachment with Radio Control Receiver Stand Apr 13 825 243 13 Ref no 5232 F 5232 FS Operating Instructions Attachment with Radio Control Receiver Attachment with Radio Control Receiver and Sensor Input Safety Instructions Attention Electrical equipment must be installed and fitted by qualified electricians only The blind shutter control has been exclusively designed for switching blind shutter motors respectively Do not switch any other loads Other applications such as controlling a sliding gate may entail certain hazards Please observe the motor manufacturers information on how to connect the blind shutter motors in parallel as well as on their reversing time and maximum duty cycle ED Function This attachment with radio control receiver is a component of the Blind Shutter Management and the Radio Management systems It is used in combination with a motor control insert Depending on the actuation of a radio transmitter e g hand held radio transmitter or on manual control through the attachment the shutter Slats will be readjusted short pressing of the pushbutton lt 1 s or the entire blind shutter moved long pressing of the pushbutton gt 1 s respectively The attachment with radio control receiver can accommodate up to 30 radio channels JUNG Attachment with Radio Control Receiver Ref no 5232 F i52Z32 FS Fig A Lightscape You can for instan
6. ce combine into up to five lightscapes the end position of the blind shutter completely up completely down with the associated lighting configuration The latter can be saved and recalled with corresponding radio transmitters e g Komfort handheld radio transmitter Sensors only for attachment with radio control receiver Sun sensor The sun sensor Fig B can be attached to the window pane and offers a sunlight protection function Fix the sun sensor at the height the blind shutter is supposed to reach if the brightness exceeds the value preset by the potentiometer Prior to activating the sunlight protection function you must bring the blind shutter to its upper end position in the continuous mode running time 2 minutes The sunlight protection function will move down the blind shutter about 2 min after the preset brightness value has been exceeded This delay of about 2 min hysteresis is necessary to compensate short time brightness variations The blind shutter will not be moved up and down upon any brightness difference If the brightness remains below the preset value for at least 15 min the blind shutter will be moved up again short time brightness variations being ignored You can use the potentiometer on the back of the attachment Fig C to set the brightness value between approx 5 000 and approx 80 000 lux Position approx 80 000 lux Position approx 5 000 lux JUNG Attachment
7. ig L LL 1 min t Fig L JUNG Attachment with Radio Control Receiver Ref no 5232 F 5232 FS Operation The rocker of the attachment has two positions For operation distinction is made between long time and short time pressing of the pushbutton You can use the A key to move the blind shutter up and the WV key to move it down Short time pressing of the pushbutton up to 1 s It will move the blind shuter for the period the pushbutton is held pressed e g slat readjustment You can press the pushbutton for a short time to stop a moving blind shutter Long time pressing of the pushbutton at least 1 s It will start the blind shutter motor for some 2 min The blind shutter will be moved up or down After this time has elapsed or the mechanical or electronic limit switches have been reached the motor will stop Lightscape The end positions of a blind shutter and the corresponding lighting can be combined and stored into a lightscape You can change a lightscape any time by reprogramming Before saving or recalling a lightscape you must have programmed the lightscape key of the radio transmitter please refer to Programming a Lightscape Key Saving a lightscape 1 Move the blind shutter to the desired and position 2 Press the desired lightscape key of the radio transmitter for at least 3 s Note If the blind shutter is not at one of its end positions or on the way there while a
8. lightscape is being saved this blind shutter will not be stored in such lightscape JUNG Attachment with Radio Control Receiver Ref no 5232 F 5232 FS Radio Transmission Radio transmission takes place on a non exclusive path Therefore interference cannot be excluded This type of radio transmission is not suitable for safety applications such as emergency stops or emergency calls The range of a radio control system depends on transmitter power receiver characteristics air humidity fitting height and building conditions The figure illustrates the penetration of building materials by radio waves Dry material Permeabilit Timber gypsum gypsum plasterboards approx 90 Brickwork particle boards approx 0 Reinforced concrete approx 30 Metal metal grating aluminium lamination approx 10 Rain snow approx 0 40 Radio operation The inter connection of this radio system with other communication networks must comply with national legislation This radio system must not be used for communication beyond property boundaries If utilized in conformity with its designated use this unit fulfils the requirements of the R amp TTE Directive 1999 5 EC The complete declaration of conformity can be found in the Internet under www jung de ce The attachment with radio control receiver may be operated in all countries of the EU and the EFTA JUNG Attachment with Radio Control Receiver
Download Pdf Manuals
Related Search