Operating Instructions Windows
Contents
1. Error code Message ERROR 9 Data transfer failed Cause The transfer to the projector has not finished yet Solutions Confirm the following items 1 Is the computer properly connected to the projector 2 Have you changed the SERIAL settings or the LAN settings of the projector after connecting the computer and the projector with the software 3 Have you operated the power settings of the projector during transfer 4 Does the computer in use go into power save mode 5 Have you logged off changed user or shut down the computer in use If there is no problem with the above items please transfer the LOGO again When ERROR1 ERROR9Y appears again please turn off the power of the projector firstly and then turn it on so as to transfer the LOGO Error code Message ERROR 10 Authentication failed Cause The account name or password which has been entered is different from the one which has been set in the projector Solutions Enter the correct account name and password Error code Message ERROR 11 Projector is busy Cause The projector does not respond Solutions Try again later Error code Message ERROR 12 Projector model mismatch Cause It is not matched with the projector model which was connected when the connection is confirmed Solutions Confirm the following items 1 Is the computer properly connected to the projector 2 Have you changed the SERIAL settings o2. the software ends directly YES The LOGO data is saved After the LOGO data is saved the software is ended NO Without saving the LOGO data the software is ended CANCEL Return to the edit screen for the LOGO data by canceling End 28 List of possible errors The list below shows the error messages of the software and solutions Error code Message ERROR 1 No Connection Cause Communication between the projector and computer is not possible Solutions Confirm the following items 1 Is the computer properly connected to the projector 2 Are the SERIAL terminals of the computer and projector matched Or are the LAN settings correct Is the projector ID matched with the projector being connected If connected via LAN are the firewall settings correct Are you using COM ports assigned to other applications If the error occurs while retransferring the LOGO please turn off the power of the projector firstly and then turn it on reconnect the projector and try again Oo hw X Please refer to Connect with the projector Page 8 for more details Error code Message ERROR 2 This software does not support this model Cause The projector being connected is not supported by this application Solutions Is the projector being connected supported by this software Check the list of projector models in the attached sheet Error code Message ERROR 3 File
3. H 454 You can change the display language of the software to Japanese Target e Language X You can change the display language of the software to Chinese oa Logo Transfer Software File F LanguagetL About Target Projector e About Version The version of the software is displayed Messages on some screens such as Open file can be displayed in the language used in your computer regardless of the language setting Target Projector Select the model name of the projector to connect According to the projector type certain items in O not required to be set up are not shown or are unable to be selected LAN settings radio button Select either LAN connection or SERIAL connection See page 9 as a method of con nection with the projector LAN settings is chosen here IP Address Enter the IP address which is set in the projector to connect Port Enter the command port number which is set in the projector to connect Account Enter the account name which is set in the projector to connect 13 Password Enter the password which is set in the projector to connect e You can confirm the IP address and command port number which are set in the projector from the on screen menu or from the detail settings screen of the WEB Control of Network Function e The account name and password which are set in the projector will be the account name and password of the administrator which has b
4. software in the computer 31 Trademarks e Microsoft and its logo as well as Windows Windows XP Windows Vista and Windows 7 are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e Other company names product names or other names noted in this manual are trademarks or registered trademarks of the respective companies Note that and TM marks are not indicated in the text of this manual Notes e Unauthorized use or reproduction of part or all of this software and manual is strictly prohibited e Panasonic cannot be held liable for any effects resulting from the use of this software and manual e Panasonic reserves the right to revise this software specifications and manual contents without notice Panasonic Corporation Web Site http panasonic net avc projector Panasonic Corporation 2010
5. the Open LOGO data the Open file dialog box appears and select the file you want to open dat After the file is loaded the main screen to create the LOGO data appears Go to page 18 _17 Edit the LOGO data If the LOGO data can be enlarged and edited in the projector it is possible to enlarge the LOGO data change the display position and set the background and transparent color If the LOGO data cannot be enlarged and edited in the projector the LOGO data which has been loaded from the Bitmap is directly transferred X If the LOGO data can be enlarged or edited in the projector go to page 21 File Language L About A 18 SYSTEM menu e File Exit End this software Language L About A e Language English You can change the display language of the software to English Language H Aa File F You can change the display language of the software to Japanese e Language gt H3Z You can change the display language of the software to Chinese e About Version The version of the software is displayed Messages on some screens such as Open file can be displayed in the language used in your computer regardless of the language setting Preview Screen The display condition of the actual LOGO is displayed in the reduced size images in the same way as the screen projected by the projector being connected Open Save The menu to load and save the LOGO d
6. the projector to connect and set the selectable items lt Fig 1 gt D CCCIUIT Us 9 6 8e Y SYSTEM menu e File Exit End this software e Language English You can change the display language of the software to English Language gt H 455 You can change the display EEEO language of the software to Japanese cpt C e Language gt H X You can change the display language of the software to Chinese e About Version Version The version of the software is displayed Messages on some screens such as Open file can be displayed in the language used in your computer regardless of the language setting 10 Target Projector Select the model name of the projector to connect The items which are unnecessary to set among the following will not be displayed or will not be selectable depending on the selected projector COM setting radio button You can select either SERIAL RS 232C connection or LAN connection See page 12 as a method of connection with the projector COM Setting is chosen here Projector ID Specify the ID number which is set in the projector to connect Select ALL or a number from 1 64 Port Select the COM port number of the computer used in the connection with the projector Baud rate Select the baud rate of the SERIAL RS 232C which is set in the projector Parity Select the parity of the SERIAL RS 232C which is set in the projector to conne
7. which you have created are collectively referred to as LOGO in this operation manual This projector can display LOGOs when it starts projecting or when it detects no signals Customers can create any LOGO that customers want to display on the projector from Bitmaps with this software It is possible to transfer the LOGO data which has been created to the projector by using this software through serial communication RS 232C or LAN It is also possible to save the LOGO data which has already been registered into the projector by loading it into the computer In addition you can set the size of the LOGO the position on the screen and background colors via this software X The restrictions of this software vary depending on the projector which you use For details refer to the List of Software Restrictions 1 If you still have the CD ROM for this software that is supplied with your projector refer to List of Software Restrictions in the application launcher of the CD ROM You can also find the latest information under List of Software Restrictions on our website http panasonic net avc projector Restrictions The restrictions of this software vary depending on the projector which you use If you still have the CD ROM for this software that is supplied with your projector refer to List of Software Restrictions in the application launcher of the CD ROM You can also find the latest information under List of S
8. Do not share your password with anyone else e In some network environments a firewall should be used for security purposes It is possible to connect via Wireless LAN depending on the projector but it is not recommended that you use this software via Wireless LAN Panasonic shall not be liable for any security issues from a Wireless LAN environment if you connect via Wireless LAN Software Installation OS Microsoft Windows XP Professional 32 bit Home Edition 32 bit Windows Vista Ultimate 32 bit 64 bit Business 32 bit 64 bit Home Premium 32 bit 64 bit Home Basic 32 bit 64 bit Windows 7 Ultimate 32 bit 64 bit Professional 32 bit 64 bit Home Premium 32 bit 64 bit e Compatible with above mentioned Japanese English and Chinese OS e Compatible with Microsoft Windows XP SP2 and SP3 e Compatible with versions up till Microsoft Windows Vista SP2 e Compatible with versions up till Windows 7 SP1 Other requirements e Please make sure that CPU RAM must meet all Microsoft OS system requirements e Display resolution shall be XGA or higher and the number of colors on the screen must be more than 16 bits e Either a Serial terminal or LAN terminal is necessary Operation is not guaranteed when used with system environments other than the above or on homemade computers Operation is not guaranteed for all computers that meet the above conditions X Images used in this software manual may be subject t
9. Licensee Article 2 Use by a Third Party Licensee may not transfer or allow any third party to use the Software or a copy of the Software whether free of charge or not Article 3 Restrictions on Copying the Software Licensee may make a single copy of the Software solely for backup purposes Article 4 Computers Licensee may install and use the Software on more than one computer owned or managed by Licensee Article 5 Reverse Engineering Decompiling or Disassembly Licensee may not reverse engineer decompile or disassemble the Software Panasonic shall not be bound by warranty for any defects in the Software caused by Licensee s reverse engineering decompiling or disassembly of the Software Furthermore Panasonic or its distributors or dealers will not be responsible for any damage to the Licensee caused by Licensee s reverse engineering decompiling or disassembly of the Software Article 6 After sales Service If a problem should occur with the Software while Licensee is using the Software Licensee should notify Panasonic of the problem by telephone or in writing Panasonic shall undertake to notify Licensee of information such as whether the problem is a known error in the program bug or whether the way in which the Software is used should be modified Furthermore the Software is subject to revision without notice Article 7 Indemnification Panasonic s liability with respect to this Software is limited to the conditions defined in Ar
10. Panasonic Operating Instructions Logo Transfer Software 2 0 M1010KT1011 FJ TQBH9021 1 E Table of Contents Read This First Restrictions The number of LOGOs the maximum pixel size and colors you can register The LOGO file format Computer Settings and Operation Projector Operation Software Licensing Agreement Security Software Installation System requirement Installation Software Uninstall Starting the Software Connect with the projector Connect via SERIAL RS 232C Connect via LAN Read This First Select a method to create the OS ec re er ee eu a 15 Create New LOGO data 16 Load LOGO data From Projector 17 Open LOGO data 17 Edit the LOGO data 18 If the LOGO data cannot be enlarged and edited in the projector 18 If the LOGO data can be enlarged and edited in the projector 21 Transfer the LOGO data 26 Saving the LOGO data 26 Change the projector to connect 27 Selection screen to connect 27 Ending the Software 28 List of possible errors 29 Trademarks 236 iee eee seins sua 32 This operation manual is for the Logo Transfer Software Pictures and characters
11. ata is displayed The projector being connected The model name of the projector being connected now is displayed Change the Target Projector Change the projector model to connect Go to page 27 19 Create New LOGO data Load a new Bitmap See page 16 Load LOGO data From Projector The LOGO data registered in the projector is loaded See page 17 Open LOGO data Load the LOGO data saved in the computer See page 17 Note If the data is loaded by the operations of O and the LOGO data being displayed now is annulled If the data is already being displayed in the preview screen and you have to save it save the LOGO data before you perform the operations of and Save LOGO data Save the LOGO data in the computer Go to page 26 Transfer Display the menu to transfer the LOGO data to the projector D Transfer LOGO data Transfer the LOGO data to the projector in the image being displayed in the preview screen Go to page 26 2 EXIT End this software 20 21 Magnification 8 00 e 89 090 GG File E Language L About A SYSTEM menu e File Exit End this software e Language English You can change the display language of the software to English e Language Asa You can change the display language of the software to Japanese e Language gt x You can change the display language of the sof
12. ct EXIT End this software OK Connection with the projector will be made according to the input settings 3 Complete the connection of the projector The screen to select a method to create the LOGO data will appear after the settings from to are completed and the connection with the projector is established in Go to page 15 _11 1 Preparation If you connect the computer with the projector directly with the LAN cable connect via a cross LAN cable Otherwise such as if hooked up via a HUB connect via a straight LAN cable 2 Network settings Set up the network of the computer which is used in the connection with the projector For details refer to your network administrator 3 Setting Confirm the network settings of the projector to connect and set the IP address port account and password Keep the NETWORK CONTROL or COMMAND CONTROL in the NETWORK menu of the projector ON A connection cannot be made if it is OFF File E Language L About A PT D6000 j PT DW6300 PT DZ6700 PT 0Z6710 PT D5000 L Account 00 e o eG 8e NO v v v v 12 SYSTEM menu e File Exit End this software oa Logo Transfer Software File E Laneuage L About A C Prot e Language English You can change the display language of the software to English A Logo Transfer Software File E Language L About A English E AEG PTDL chi C Language
13. een set in the WEB Control of Network Function or in user s authority e The account name will be fixed depending on the projector model to connect EXIT End this software OK Connection with the projector will be made according to the input settings 4 Complete the connection of the projector The screen to select a method to create the LOGO data will be displayed after the settings from to are completed and the connection with the projector is established in Go to page 15 _14 Select a method to create the LOGO data After the connection between the computer and the projector is established the following screen will appear Select the method to create which is best suited for your purpose CANCEL D Create New LOGO data Create the LOGO data with the Bitmap saved in your computer See page 16 Load LOGO data From Projector Create the LOGO data with the LOGO data registered in the projector See page 17 This function might be disabled depending on the connected projector or method of connection Open LOGO data Create the LOGO data with the LOGO data which was already created once and has been saved in your computer See page 17 EXIT End this software 6 CANCEL Return to the selection screen to connect 15 Open file dialog box appears when you select Create New LOGO data Select the Bitmap you want to use for the LOGO data The edit screen for the LOGO data will a
14. eturn to the screen for editing the LOGO data Saving the LOGO data If you perform Save LOGO data the dialog box Save as appears Enter the file name and save 26 Change the projector to connect If a model of projector which is different from the one being connected now is connected continuously you need to change the projector to connect If you are editing the LOGO data the following confirmation screen for Save appears YES The LOGO data is saved After the LOGO data is saved the selection screen to connect appears NO The LOGO data is not saved The selection screen to connect appears CANCEL Return to the edit screen for the LOGO data by canceling the change of the projector If the change of the projector is selected the selection screen to connect appears Return to the Connect with the projector Go to page 8 and select the projector model to make a new connection and perform the settings Click the CANCEL button to return to the edit screen for the LOGO data x A fa _ ooo File E Language L About A File E Language L About A PT D6000 PT DW6300 PT DZ6700 PT DZ6710 PT D5000 v O i 1 f JC cac K CANCEL _ 27 Ending the Software End this software If you are editing the LOGO data the following confirmation screen appears If you are not editing the LOGO data the following confirmation screen does not appear and
15. ftware The data is updated every time you connect and is overwritten with the set information of your last connection If you delete this file the previously set record is deleted but it is newly and automatically created when you connect after you start the software the next time Connect with the projector You need to connect the computer to the projector in order to transfer the LOGO data from your computer There are two ways to connect 1 Serial RS 232C connection and 2 LAN connection e Only the serial connection RS 232C may be possible depending on the projector model If you still have the CD ROM for this software that is supplied with your projector refer to List of Software Restrictions in the application launcher of the CD ROM You can also find the latest information under List of Software Restrictions on our website http panasonic net avc projector e If the computer and projector are not connected this software stops at the selection screen to connect e For information such as communication conditions of the projector to connect and LAN settings please refer to the manual of the projector 1 Preparation Connect the computer with the SERIAL RS 232C IN terminal of the projector via the D Sub 9 pin straight cable The name of the SERIAL RS 232C IN terminal varies depending on the projector model 2 Setting The setting items vary depending on the projector to connect as in figures 1 and 2 Select
16. he computer Go to page 26 D Setting The menu to edit and set the loaded LOGO is displayed 2 Set the Magnification horizontal You can change the size of the LOGO data within the range of the screen The selectable magnifications are x1 x2 x4 and x8 e If the size is changed the display position becomes the center position e Use of this function may not be possible depending on the connected projector D Magnification vertical You can change the size of the LOGO data within the range of the screen The selectable magnifications are x1 x2 x4 and x8 e If the size is changed the display position becomes the center position e Use of this function may not be possible depending on the connected projector Center check box Place the LOGO data in the center of the screen e If it is moved outside the center clear the check box e Use of this function may not be possible depending on the connected projector 5 Upper Left Coordinates horizontal You can move the position of the LOGO data within the range of the screen Use of this function may not be possible depending on the connected projector Upper Left Coordinates vertical You can move the position of the LOGO data within the range of the screen Use of this function may not be possible depending on the connected projector _24 D Background Color Select ON OFF for the background color around the LOGO data Preview Screen Background color ON Col
17. o change without notice 1 When installing with the software CD ROM Start the application launcher and click the Install button waa 7 9 Tensfor Software Setup Wizard i Logo Transfer Software of the Logo Transfer Software to start installation The installer will guide you through the steps required to install Lago Transfer Software on your computer When installing with file downloaded from the Web Unzip the downloaded files from the web P WARNING rhi Ea Pyomam ie RD CNET cu reaties F Double click the Setup exe file in the unzipped folder to yiya aaa a man a a aaa start installation Follow the installation instructions on screen 2 Ashortcut will appear after installation is completed e Microsoft NET Framework 2 0 must be installed on the computer before installing this software Administrator authority is required to install Microsoft NET Framework 2 0 Please download Microsoft NET Framework Version 2 0 from Microsoft s Download Center e The application launcher will launch automatically when the CD ROM recorded with this software is inserted into the CD Driver If the launcher does not start please double click the Launcher exe file in the CD ROM e When installing from the CD ROM please choose the Execute Launcher exe from the autoplay screen e When the same version of the software is already installed repair and delete options will also be shown on screen e To uninstall sof
18. oftware Restrictions on our website http panasonic net avc projector Only the BMP Bitmap LOGO file can be applied on this model lt Copyright gt When you create the LOGO data with this software you must receive the approval of the copyright holder for the Bitmap used for the LOGO It is prohibited by copyright laws to copy distribute and deliver copyrighted materials without the prior approval of the copyright holder except as approved by the relevant copyright laws Panasonic shall not be liable for any issues that may be caused by using the Bitmap without proper approval LOGO transfer might fail if the computer in use is set to power save mode Please do not set the computer in use to power save mode when using this software LOGO transfer might fail if the computer is logged off shut down or the user is changed Please do not log off change user or shut down the computer when using this software LOGO transfer might fail if the projector is turned on or off Please do not change the projector power setting when using this software Software Licensing Agreement You must agree to the terms defined in this Software Licensing Agreement to use this Software By using this Software you are agreeing to the Software Licensing Agreement Article 1 Rights Licensee is granted the rights to use this Software but all applicable rights to copyrights or intellectual property rights of the Software are not transferable to the
19. or setting Red LOGO data The background color around the LOGO data is red Example Color Setting button Set the color used for the background The Color Setting dialog box of OS standard is displayed Transparent Color Areas other than the color set as the transparent color in the LOGO data can be displayed by setting one dot color in the upper left of the LOGO data as the transparent color Preview Screen om ns Less The set LOGO data The same color as the dot in the upper left is transparent Transfer Display the menu to transfer the LOGO data to the projector Transfer LOGO data Transfer the LOGO data to the projector in the image being displayed in the preview screen Go to page 26 EXIT End this software 25 Transfer the LOGO data When you perform Transfer LOGO data the following screen will appear Logo Transfer Software Connected D12000 4 Overwrite LOGO data Please select LOGO data Projector Logo LOGO 1 D OLOGO 2 D Select the LOGO data of the projector Specify the LOGO data to transfer e If your projector has only one location to register the LOGO data you do not need to select the LOGO Click the OK button e Time to load the LOGO data will be different for different projectors OK Transfer the LOGO data which has been specified The edit screen for the LOGO data will appear after the LOGO data is transferred Go to page 18 CANCEL R
20. ppear after loading the file Go to page 18 e Only the BMP Bitmap file can be used for the LOGO data e The pixel size of the Bitmap which can be used for the LOGO data varies depending on the projector being connected e The number of colors which can be used for the LOGO data varies depending on the projector being connected If the number of colors used is over the usable range the color is automatically decreased in the software The restrictions of this software vary depending on the projector which you use If you still have the CD ROM for this software that is supplied with your projector refer to List of Software Restrictions in the application launcher of the CD ROM You can also find the latest information under List of Software Restrictions on our website http panasonic net avc projector 16 When you select the Load LOGO data From Projector the following screen appears After you select the LOGO to load click the OK button D Select the LOGO data of the Projector Specify the LOGO data to load e If your projector has only one location to register the LOGO data you do not need to select the LOGO Click the OK button e Time to load the LOGO data will be different for different projectors OK Load the specified LOGO data The edit screen will appear after the LOGO data is load ed Go to page 18 CANCEL Return to the screen to select a method to create the LOGO data If you select
21. r LAN settings of the projector since the connection is confirmed 3 Is the projector ID matched with the projector being connected Error code Message ERROR 13 The security of the projector is enabled Cause Solutions The security settings of the projector are enabled Set the security settings to disabled Error code Message ERROR 14 The standby mode of the projector is set to ECO mode Cause The standby mode of the projector is set to ECO Solutions Change the setting of the standby mode 30 List of possible errors cont Error code Message ERROR 15 This software does not support this projector s firmware version Cause This firmware version is not supported Solutions Consult your dealer Error code Message ERROR 16 No Data Cause The data in the LOGO which has been loaded from the projector does not exist It is not possible to retrieve the LOGO data which has not been registered Solutions Is the source of the LOGO data to load specified properly Error code Message Cause ERROR 17 Write failed Ini file The Logo Transfer Software ini file could not be saved Solutions Confirm the following items 1 Is there enough drive space to save the file 2 Do you have the authority to access the folder file to save Logo Transfer Software ini file This is the file to automatically save the value set by this
22. ticle 6 above Panasonic or any of its distributors or dealers shall not be liable for any damage suffered by Licensee either directly or through claims from a third party arising from or in connection with Licensee s use of the Software Furthermore Panasonic makes absolutely no warranty for the use of this Software for any purpose other than for applications associated with the projector with which this Software is bundled Article 8 Export Control Licensee agrees not to export or re export the Software to any country other than the country of purchase of the projector in any form without the appropriate export licenses under the regulations of the country where Licensee resides or of any other country as may be required by such export or re export m Please read the following information carefully e Panasonic shall not be liable for any data corruption caused by the projector Security The following incidents are potential threats for users of this software e Leakage of your personal information via this product e Dishonest operation by an untrusted third party e An untrusted third party locking out or preventing anyone else from using this product Take these security measures e Set a password and restrict access to authorized users only e Do not use a simple password that will be easy to guess e Change your password regularly e Panasonic Corporation and its affiliates will never ask you for the password
23. tware select Remove To repair a fault select Repair Please follow the instructions on screen i Logo Transfer Software Welcome to the Logo Transfer Software Setup Wizard Select whether you want to repair or remove Logo Transfer Software Repair Logo Transfer Software Remove Logo Transfer Software Cancel Back r e When Repair is selected click Cancel when the message Please insert disc appears Click Yes to the message Abort The message The installation is cancelled will appear Click Close and install again after the software is uninstalled e The font might not appear normally if you install the Japanese or Chinese version of this software in other language OS From the desktop go to Start Control Panel Add Remove Program and select Logo Transfer Software from the Add Remove Program window and click Remove Please follow the instructions on the screen to uninstall Starting the Software Double click the shortcut icon on the desktop or choose Start Panasonic Logo Transfer Software Logo Transfer Software The connection terminal selection screen will appear after the splash window appears eo Logo TransterS i oftware Eeccceccecocsecoccccesesocsecsesesossed e The file Logo Transfer Software ini which automatically records the set value is automatically created in the same folder as the execution file when you connect via this so
24. tware to Chinese e About Version File E Laneuage L The version of the software is displayed Messages on some screens such as Open file can be displayed in the language used in your computer regardless of the language setting 22 Bitmap Screen The loaded LOGO data is displayed The bitmap screen may not appear depending on the connected projector Preview Screen The display condition of the actual LOGO is displayed in the reduced size images in the same way as the screen projected by the projector being connected Open Save The menu to load and save the LOGO data is displayed The Projector being connected The model name of the projector being connected is now displayed Change the Target Projector Change the projector model to connect Go to page 27 Create New LOGO data Load a new Bitmap Go to page 16 Load LOGO data From Projector The LOGO data registered in the projector is loaded Go to page 17 This function might be disabled depending on the connected projector or method of connection Open LOGO data Load the LOGO data saved in the computer Go to page 17 Note If the data is loaded by the operations of D and the LOGO data being displayed now is annulled If the data is already being displayed in the preview screen and you have to save it save the LOGO data before you perform the operations of D and 23 Save LOGO data Save the LOGO data in t
25. type not supported Cause An invalid file has been selected Solutions Confirm the following items 1 Is the file in the Bitmap format 2 Is the selected file the LOGO data file which has been created by this software Error code Message ERROR 4 File size exceeded Cause The Bitmap of the size which is not supported has been specified Solutions Confirm the size of the Bitmap Error code Message ERROR 5 The bitmap size is not 1024x768 Cause The Bitmap of the size which is not supported has been specified Solutions Confirm the size of the Bitmap Error code Message ERROR 6 The bitmap size is not 1280x800 Cause The Bitmap of the size which is not supported has been specified Solutions Confirm the size of the Bitmap Error code Message ERROR 7 The projector is not in Standby Cause The power of the projector is turned ON Solutions Confirm the following items 1 Is the power of the projector turned OFF 2 Has the spinning of the fan of the projector stopped 3 Is your projector supported by this application 29 List of possible errors cont Error code Message ERROR 8 Write failed Cause The file could not be saved Solutions Confirm the following items 1 Is there enough drive space to save the file 2 Do you have the authority to access the folder file to save
Download Pdf Manuals
Related Search