OpErAting instructions
Contents
1. To change the model type shown as an icon on the right of the screen press both outer buttons at the same time The programming functions that can be accessed using the programmer are detailed in the chart below Helicopter Boat Car Aircraft Select Battery Select Battery Select Battery Cut Off Voltage Cut Off Voltage Cut Off Voltage Cut Off Type Cut Off Type Cut Off Type Motor Direction Motor Direction Motor Direction Advance Timing Advance Timing Advance Timing Acceleration Acceleration Acceleration Start Power Start Power Start Power Response to Governor Reverse Function Air Brake Type Governor ON OFF Motor Pole Number Air Brake ON OFF Motor Pole Number Gear Ratio Motor Pole Number Gear Ratio Max RPM Gear Ratio Max RPM Average RPM Max RPM Average RPM Download Average RPM Download Restore Memory Download Restore Memory Back Up Memory Restore Memory Back Up Memory Back Up Memory N B After changing any settings using the programmer the new settings must be downloaded to the controller Model Type Press both outer buttons on the programmer up and down at the same time to change the model type between Aircraft Helicopter Car amp Boat Battery Type Use the or buttons to select the type of battery being used eee N B It is very important that the correct battery type is selected as different battery types require the controller to cut off at different voltages If a Lithium battery is allowed to dis2. Brushless Speed Controllers FS HWKO008 FS HWK018 FS HWK030 FS HWK040 FS HWKO050 FS HWKO060 FS HWKO75 FS HWK100 FS HWK120 FS HWKPROG Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL Hawk BL 8A 18A 30A 40A 50A 60A 75A 100A 120A Nixx 6 12 Li Po 2 4 Cells Nixx 6 12 Li Po 2 4 Cells Nixx 6 18 Li Po 2 6 Cells Nixx 6 18 Li Po 2 6 Cells Nixx 6 18 Li Po 2 6 Cells Nixx 6 18 Li Po 2 6 Cells Nixx 14 36 Li Po 4 12 Cells Nixx 14 36 Li Po 4 12 Cells Nixx 14 36 Li Po 4 12 Cells ESC Programmer Thank you for purchasing this Fusion Hawk Speed Controller or programmer We are sure you will be pleased with its performance and features In order to ensure that you obtain the maximum benefit from its operation please read the instructions carefully OPERATING INSTRUCTIONS Please keep for Future Reference SPECIFICATIONS Hawk 008 Load Current 8A Peak Load 12A p 35 x 22 Dimensions mm x7 Weight g 15g NiCD NiMH Cells 6 12 Li Po Cells 2 4 5 5V BEG max 2A Programmable Yes Rx Filter Yes Low Voltage Cut Off Yes Power on Reset Yes High Motor Frequency 32 kHz Thermal Protection Yes Cool Power FET FEATURES Hawk 018 18A 22A 38 x 22 X 25g 6 12 2 4 5 5V max 2A Yes Yes Yes 32 kHz Yes e Compact amp lightweight Hawk 030 30A 35A 49 x 25 x10 29g 6 18 2 6 5 5V max 3A Yes Yes Yes 32 kHz Yes Yes e Cool Power
3. FET technology Hawk 040 40A 50A 66 x 25 x 10 47g 6 18 2 6 5 5V max 3A peak 5A Yes Yes Yes Yes 32 kHz Yes Yes Hawk 050 50A 60A 66 x 25 x 10 49g 6 18 2 6 5 5V max 3A peak 5A Yes Yes Yes Yes 32 kHz Yes Yes Hawk 060 60A 70A 66 x 25 x 10 49g 6 18 2 6 5 5V max 3A peak 5A Yes Yes Yes Yes 32 kHz Yes Yes e Safe Start prevents the motor starting accidentally Hawk Hawk Hawk 075 100 120 75A 100A 120A 85A 120A 150A 78x29 73x56 73x56 x 14 x31 x31 79g 162g 166g 14 36 14 36 14 36 4 12 4 12 4 12 None None None Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 32 kHz 32kHz 32 kHz Yes Yes Yes Yes Yes Yes with Fan with Fan e Low Voltage Cut Off programmed from the battery selection that you make in the set up procedure NiCd NiMH Li Po e Ideal for AIRCRAFT BOATS CARS amp HELICOPTERS e Designed in conjunction with the Fusion Brushless motors but can be used with any brushless motor e Advanced programming possible with the optional programmer CONNECTIONS Attach suitable connectors for connection to the drive battery Red Black Ensure all of the connections are suitably insulated with heat shrink sleeving Positive Negative 1 2 3 4 5 6 7 8 Setting the Full Throttle Stop amp Reverse Stick Positions Connect the speed controller as shown in the photograph but DO NOT connect the drive batt
4. Car Boat Parameter 4 AIRCRAFT HELICOPTER 4 4 Parameter 5 BOAT CAR 5 EDITTING PARAMETERS When you have selected the Parameter you want to change move the Full Throttle throttle stick from the Full Throttle position to the Stop position and i leave it there for at least 3 seconds The motor will emit a multi tone I bleep to confirm you are now editing a parameter then the setting for Stop the selected parameter will be displayed and beeped as per the table below Parameter Parameter type LED ON LED FLASHES Number Beep every Beep every 2 seconds 0 5 seconds 1 Battery Type Li Po NiCd NiMH 2 Direction of Rotation Normal Reverse 3 Brake Aircraft OFF ON Governor Helicopter OFF ON Reverse Car Boat OFF ON 4 Model Type AIRCRAFT HELICOPTER Aircraft Helicopter 5 Model Type BOAT CAR Boat Car IMPORTANT NOTE Editing parameters 4 or 5 Model Types will cause the model type to be changed and the other parameters may be reset THESE MUST BE SET FIRST before any other parameters are changed You can then toggle the setting in the parameter by moving the throttle ull Trew stick from the Stop position to the Full Throttle position and back again to the Stop position The setting can been seen by the LED being on or flashing and the frequency of the beeps see the table above I Stop To store the setting move the throttle stick forward to the Full Throttle Full Thote po
5. NOT connect the drive battery yet 2 Switch the Transmitter ON Full Throttle 3 Move the throttle stick forward to the FULL THROTTLE position j 4 Connect the drive battery to the speed controller The motor will l emit a short series of beeps to confirm the connection 5 After around 10 seconds the motor will emit a double series of beeps Wait a further 3 seconds and you will hear a triple series of beeps followed by single beeps together with the LED giving a single flashes confirming that Parameter 1 is now selected SELECTING A PARAMETER After entering programming mode the motor should be emitting a single 9 FulThrottie beep and the LED will emit a single flash to show that parameter 1 is currently selected To move to the next parameter move the throttle i stick from the Full Throttle position to the Stop position and then l back again to the Full Throttle position again Siok The controller will now emit continuous double beeps and the LED will flash twice to show that Parameter 2 has been selected Repeat the stick movements again and you will hear continuous triple beeps with the LED flashing 3 times to show that Parameter 3 has been selected and so on for Parameters 4 and 5 PROGRAMMABLE LED PARAMETERS Parameter Type Beep Flashes Parameter 1 Battery type 1 1 Parameter 2 Motor Rotation Direction 2 2 Parameter 3 Brake ON OFF Aircraft Governor ON OFF Helicopter 3 B Reverse ON OFF
6. bles Always avoid short circuits e Keep the speed controller and the programmer dry and away from water oil and grease Ensure adequate air circulation around the speed controller Always keep clear of the rotor blades propellers and wheels when the drive battery is connected e Always keep within the values stated in the speed controllers specification wouw LoscRC com Logic RC Limited 14 Hartham Lane Hertford SG14 1QN United Kingdom rev 12 09
7. charge below it s minimum voltage then permanent damage can be caused to the battery Cut Off Voltage The Cut Off Voltage varies according to the battery type leer rer that you have set In AUTO mode the cut off for Li Po is 3 0V per cell and for NiCd NiMH is 5 5V variable cut off type However you can set the range manually using the and buttons from 4 5V 33 0V Cut Off Type In Cut Off Type mode you can select the cut off method PETRE when the battery falls below the selected cut off voltage Use the and buttons to switch between the two options of SOFT OFF or HARD OFF Motor Direction The direction of the motor rotation can be selected between NORMAL and REVERSE Advance Timing Advance timing or Motor Timing alters the advance of Be the rotational field which has a similar effect to advancing the ignition point 8 is suitable for most motors but if you want to use a special setup for your motor we would recommend the following ranges 0 10 for in runner motors and 15 25 for out runner motors Acceleration You can set the rate of acceleration to your motor using eee the and buttons choosing between Lowest Low Normal High Highest Similar to Acceleration Start Power allows you to determine the level of power fed to the motor when it starts up Choosing between Lowest Low Normal High Highest Air Bra
8. ery yet Switch the Transmitter ON Move the throttle stick forward to the FULL THROTTLE position Full Throttle Now connect the drive battery to the speed controller The motor Ri will emit a short series of beeps to confirm the connection If the LED lights up disconnect the drive battery and reverse the servo reverse switch on the transmitter and start again from number 1 After around 10 seconds the motor will emit a double series of beeps to confirm that it has detected the full throttle position Within 2 seconds move the throttle stick to the STOP position Again the motor will emit a short series of beeps to confirm that it has detected the stop position If using the reverse function move the throttle stick to the REVERSE position The motor will emit a short series of triple beeps to confirm that it has detected the reverse position If you don t require the reverse function then just leave the throttle stick in the stop position for approximately ten seconds and the controller will confirm the settings with a series of triple beeps After the triple beeps disconnect the drive battery to complete the setup BASIC PROGRAMMING Basic parameters can be edited by moving the throttle stick on the radio as detailed below More advanced programming can be performed using the optional programmer unit ENTERING THE PROGRAMMING MODE 1 Connect the speed controller as shown in the photograph but DO
9. ke ON OFF AIR mode only This menu is used for switching the Air Brake On or Off Air Brake Type In AIR mode model aircraft it is possible to adjust the effect of the motor brake and select whether the motor stops slowly for a soft braking effect or quickly for a hard braking effect The and buttons allow you to select from Slow Normal Fast Reverse Function BOAT amp CAR modes only This menu is used for switching between One Way forward only and Two Way forward and reverse Be careful that changing the direction of the motor doesn t cancel any of the other settings Governor ON OFF HELI mode only This mode is used for switching the speed governor on and off The Governor mode stabilises the pre set rotational speed and keeps it virtually constant Governor Response HELI mode only This is used for setting the characteristics of the speed controller in speed governor mode The available options of Slowest Slow Normal Fast Fastest can be chosen by using the and buttons CAUTION The faster the value you select the higher the current draw from the battery We recommend that you select a fairly low setting to avoid premature damage to the speed controller and drive battery Motor Pole Number This menu allows you to enter the number of poles in your motor between 2 36 poles This value is very important for indicating the exact rotational speed This menu a
10. llows you to enter the gear ratio you are using in your gearbox from 1 0 1 to 25 0 1 The value for rotational speed indication is calculated using the number of motor poles and the gearbox reduction ratio Maximum RPM amp Average RPM This mode shows you the maximum and the average rotational speeds recorded during the last flight using a 0 e A i fay 9 the Motor Pole Number and Gear Ratio values from above Download This mode is used for transferring the new settings to the speed controller Press the button to start the process and the programmer will beep once every second until the procedure is complete If you wish to interrupt the process press the button Restore Memory Restore Memory is used to access values which have eae been stored in the Programmer s own memory Press the button to start the process and the programmer then beeps once every second until the procedure is complete If you wish to interrupt the process press the button Backup Memory This mode allows you to store the selected values in the ae programmer s integral memory permanently Press the button to start the process and the programmer then beeps once every second until the procedure is complete The values set on the speed controller are not affected by this action If you wish to interrupt the process press the button Always ensure the correct polarity in all connecting ca
11. sition and leave it there for at least 3 seconds The motor will emit a j multi tone bleep to confirm you have stored the parameter then return t to the parameter selection menu PROGRAMMING SUMMARY When the controller is in programming mode it will flash and beep as detailed in the programming charts above allowing you to select and edit the parameters When the throttle stick is held in the FULL THROTTLE position the parameter number is flashed and beeped as detailed in the parameter chart above Moving the stick down then back up again allows you to move to the next parameter When the throttle stick is moved to and held in the STOP position the controller will enter the selected parameter and will flash beep at a different speed dependant on the current setting To change this setting move the throttle stick up and then back down again To save and exit the parameter move the stick back to the FULL THROTTLE position PROGRAMMING USING THE OPTIONAL PROGRAMMER lt PROGRAMMER Connect the programmer as shown in the photograph SPEED CONTROLLER _ motor CONNECTIONS lt 4 DRIVE BATTERY The Programmer is very easy to use The outer arrows are used to move between the parameters and the and buttons are used to change the settings within the programming function Dependant on the model type the prorgramming functions are laid out as shown in the table below
Download Pdf Manuals
Related Search