Yale 084001 Instructions / Assembly
Contents
1. Inside Escutcheon amp Mounting Plate with gasket B Bolt Note Bolt ships with backset in 2 3 8 posi tion If required press small black button on underside of bolt and pull to extend to 2 3 4 backset position Fig 3B C The outside escutcheon with gasket remains assembled Outside Escutcheon P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY INSTALL LOCK 1 Install bolt in door NOTE The bolt must be in a retracted unlocked position when installing the lockset Attach with 2 x 25 4mm 8 32 x 1 screws supplied e 8 32 x 1 Flat Head Combination Screws 2 Install strike on the door frame making sure to allow 2 x 25 4mm gt 8 32 x 1 Flat Head Combination Screws 3 Install outside escutcheon a As you position the outside escutcheon route the cable through 2 1 8 diameter hole Figure 3A for the bolt to be centered in the strike Figure 3A 4 Holding the outside escutcheon flush to the door position the inside mounting plate by first routing the wire harness through the mounting plate s 1 2 hole Fig 4A then inserting mounting plate tongue into groove at bottom of outside escutcheon Secure both assemblies using 2 M6 x 59 5mm pan head machine screws Fig 4B making sure that outside escutcheon is vertically aligned Hand tighten2. 1 25 without network module 7 Gu Master PIN Code Setting E M D B E 1 250 with network module Edu PIN Code 0 ES gt E gt 2 25 oB Default settings in bold 8 E 2 Privacy Button Setting 6 O 2 Performs automatic handing of the lock For quiet areas select Disable 3 gt E in Audio Mode All Code Lockout Mode 8 E a a E i Note If the lock is connected to a network controller it is 0 eivor vocu 8 recommended that it is programmed through the centralized user interface PC or hand held device to ensure communi This function appears onl ei gt cation between the lock and the controller unit installed P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY MISCELLANEOUS Hardware Troubleshooting Programming Troubleshooting Installing the Network Module Replace Install Cylinder Sample Pin Code Management Sheets TROUBLESHOOTING Hardware Troubleshooting D Cycle the lock in both the locked and the unlocked positions If problems are found Symptom Suggested Action Door is binding Check that door and frame are properly aligned and door is free swinging Check hinges They should not be loose or have excessive wear on knuckles Bolt will not deadlock Check for sufficient clearance of the bolt within the stri
3. Installation Instructions Inside Mounting Plate Strike Plate C Door Marker _ Battery Cover Screw Pack O Outside Escutcheon O 4 AA Alkaline Batteries O Keys Parts Illustrations 1111 4 AA Alkaline Batteries Inside Mounting Plate Outside Inside with Gasket Escutcheon Escutcheon back of Inside Escutcheon oe 3 Inside Escutcheon Z A 4 Bolt amp Strike Plate Mounting screws Mounting Screws Network Module Optional 2 Through bolts Tools Needed Door Prep Lock Installation 2 1 8 64mm hole saw a 2 Phillips screwdriver 1 26mm boring bit 7 64 2 5mm drill bit Chisel amp hammer P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY PREPARE LOCK FOR INSTALLATION Unpack the Lock The lock is packed representative of how it will install on the door Before installing the lock on the door A Inside escutcheon 1 Loosen the screw Phillips 2 holding the battery cover The screw remains attached to the Battery Cover battery cover Slide the battery cover up and out note the two tabs at bottom of battery cover Remove the inside mounting plate with gasket from the back door side of the inside escutcheon a Ensure that gasket on Inside Mounting Plate is properly fitted Note the positioning of the gasket s five rubber nubs Figure 3A
4. off and on the user 15 encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY Industry Canada Canadian ID 6982A YRHCPZWO Z Wave 6982A YRHCPZBO Zigbee This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet num rique de la classe B r pond toutes les exigences de l interf rence canadienne causant des reglements d quipement L op ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dispositif doit accepter n importe quelle interf rence re ue compris l interf rence qui peut causer l op ration peu d sir e For the U4A YRHCPZBO and 6982A YRHCPZBO the following statement applies This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled enviro
5. plate Fig 8 3 Pan head screws IMPORTANT Before installing the batteries test the mechanical operation of the lock by using both thumbturn and the key The movement of the Figure 8 bolt should be smooth and unobstructed If operation is not smooth review the previous steps to ensure proper installation NOTES The bolt must be in a retracted unlocked position prior to installing the batteries Refer to programming instructions prior to completion of 4 AA Batteries the next step Step 10 10 Insert four 4 AA alkaline batteries The lock responds with a series of beeps a red blue flash and a quick flash of all keypad LEDs When activating the lock for the first time the lock will adjust for proper handing 11 Install battery cover and tighten Phillips head screw Figure 9 P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY PROGRAMMING Programming Features Menus Keys Definitions Operation PROGRAMMING FEATURES MENUS KEYS DEFINITIONS Outside Inside Status Indicator Phillips Head Screw Battery Cover Network Module Slot Numbers Alkaline Batteries Cylinder Status Indicator Thumbturn Privacy Mode Button A unique Master PIN Code must be entered registered prior to any further programming of the lock See section on page 11 Register Master PIN Co
6. All Code Lockout Mode 15 enabled Only the Master can enable disable All Code Lockout Mode Contact the Master user Upon entering a PIN code and press ing the key there are different tones Check to see if the lock 15 set to All Code Lockout Mode Setting managing All Code Lockout Mode is done through Master Code only Contact the Master user The unit operates but it makes no sound Enable Audio Mode The unit displays intermittent RED flashes This is the Low Battery indicator alerting that it is time to replace the batteries Replace all four 4 batteries with new AA Alkaline batteries Upon entering a PIN code and press ing the star key the unit responds with a series of beeps and the keypad flashes three times The digits entered were incorrect or incomplete Re enter the correct code followed by the star key When batteries are replaced Network Module locks have a real time clock that will be set through the User Interface UI it is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time DST Network Module locks only An ASSA ABLOY Group brand P N AYRD210 INST FUL Rev E ASSA ABLOY Installing the Network Module IMPORTANT The batteries must be removed prior to removing and or inserting the network module Remove battery cover Remove batteries Remove and or insert network module Reinstall bat
7. RSS standard exemptes de licence s Son fonctionnement est soumis aux deux conditions suivantes 1 ce dispositif ne peut causer des interf rences et 2 cet appareil doit accepter toute interf rence y compris les interf rences qui peuvent causer un mauvais fonctionnement du dispositif INTRODUCTION The Yale Real Living Stand alone Push Button Deadbolt Lock combines a robust lockset with a contemporary electronic aesthetic Users benefit from a push button keypad that makes day to day access effortless for simple up dates to user information in the event of staffing changes or security breaches Yale Real Living is engineered for quick and easy installation and fits in place of a standard deadbolt lock door prep ANSI BHMA A156 115 If this is an RF enabled network lock it needs to be located within 30 50 feet of another network controller or a repeating device That distance is influenced by objects between the lock and the controller and may be expanded depending on proximity to other RF network devices Also if the lock is connected to a network controller it is recommended that it is programmed through the centralized user interface PC or hand held device to ensure communication between the lock and the controller unit P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY INSTALLATION COMPONENTS AND TOOLS Included in the box Quick Start Guide O Inside Escutcheon Bolt _
8. S w te Poe de rue i te w ee w e Poe te w te P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY ONLINE LITERATURE AND TEMPLATES For the latest information on Yale products visit our website at www yalelocks com Click on the Literature button to find the most up to date catalogs parts manuals templates specifications and installation instructions Scan this code to view installation videos for this and other Yale Real Living products Yale Locks amp Hardware 100 Sargent Drive New Haven CT 06511 Product Support Tel 800 810 WIRE 9473 www yalelocks com Yale Locks amp Hardware is a division of Yale Security Inc an ASSA ABLOY Group company Yale is a registered trademark of Yale Security Inc an ASSA ABLOY Group company All rights reserved Yale Real Living is a trademark of Yale Security Inc an ASSA ABLOY Group company Copyright 2011 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without express written permission of Yale Security Inc an ASSA ABLOY Group company is prohibited YALE with its unique global reach and range of products is the world s favorite lock the preferred solution for securing your home family and personal belongings ASSA ABLOY is the global leader in door opening solutions dedicated to satisfying end user needs for security safety and co
9. Y o Yale Real Living Push Button Deadbolt a e Installation and Programming Instructions NOTE TO INSTALLER FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT AND VOID THE FACTORY WARRANTY FS OS D UY LY Q FS N Y For Technical Assistance call Yale at 1 800 810 WIRE 9473 This document is available on our website in printed Spanish and French Go to www yalerealliving com Click Product Information 4 Documentation and then Installation Instructions Este documento est disponible en espa ol en nuestra p gina de internet Vaya a www yalerealliving com Presione Informaci n del Producto y Documentaci n y luego Instrucciones de Instalaci n Ce document est disponible sur notre site Web dans le francais imprim Allez www yalerealliving com Cliquez sur le Information sur le produit et Documentation et puis Installation Instructions P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY TABLE CONTENTS Warnings Introduction Installation Components and Tools Prepare Lock for Installation Install Lock Programming Programming Features Menus Keys Definitions Lock Operation Miscellaneous Information Hardware Troubleshooting Programming Troubleshooting Installing the Network Module Replace lnstall Cylinder Sample Pin Cod
10. aster PIN code must be registered prior to any other programming of the lock Adjustable only when using Network Module with compatible integrated controller P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY Open Door with Code 1 2 3 Enter PIN code Complete the code entry Unlock by pressing the key Privacy Mode vs All Code Lockout Mode All Code Lockout is a Menu feature 6 that restricts Pin code access except Master Privacy mode is set by pressing and holding the privacy button found below thumbturn for a duration of four beeps This deactivates the keypad and sound and because it is set from the inside provides a secure and silent lock for the convenience of the occupant s Both features can be enabled or disabled from the Main Menu P N AYRD210 INST FUL Rev E ASSA ABLOY An ASSA ABLOY Group brand Feature Programming Through Menu Mode Using Master PIN code 1 Enter the 4 8 digit Master code followed by the a key 2 Enter digit corresponding to the function to be performed followed by the a key Note If the lock is connected to a network controller it is recommended that it is programmed through the centralized user interface PC or hand held device to ensure communication between the lock and the controller unit The Master PIN code must be registered prior to any other programming of the lock 1 2 User Number UN
11. de Before Programming Menu and Icons Used in This Guide Click the indicated number Enter Master PIN code 4 8 digits in e length Press the Star key on the keypad to Enter Enter User PIN Can be 4 8 digits in or Accept entry length Press the Pound key on the keypad to User Number 1 25 enter Menu mode RF Controlled 1 250 P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY Status Indicators Enter the Menu Mode Definitions All Code Lockout Mode This feature is enabled by the Master code When enabled it restricts all user except Master PIN code access When attempting to enter a code while the unit is in Lockout the Status Indicator flashes RED and BLUE 8 times the keypad flashes as well Audio Mode Choosing Disable 3 in Audio mode shuts off the code confirmation tone play back for use in quiet areas Audio mode is enabled or disabled through feature programming by the Master PIN code Automatic Re lock Time After successful code entry and the unit unlocks it will automatically re lock after a default of thirty 30 seconds Re lock time is adjustable from 10 180 seconds Inside Indicator Light Shows active status Locked of lock and can be enabled or disabled in the Advanced Lock Settings Main Menu selection 3 Low Battery When battery power is low the Status Indicator flashes RED If batte
12. e Management Sheets WARNINGS Warning Changes or modifications to this device not expressly approved by Yale Security Inc could void the user s authority to operate the equipment IMPORTANT The accuracy of the door preparation is critical for the proper functioning and security of this product Misalignment can cause performance degradation and a lessening of security Finish Care This lockset is designed to provide the highest standard of product quality and performance Care should be taken to ensure a long lasting finish When cleaning is required use a soft damp cloth Using lacquer thinner caustic soaps abrasive cleaners or polishes could damage the coating and result in tarnishing FCC FCC ID U4A YRHCPZWO Z Wave U4A YRHCPZBO Zigbee Model s YRD210 ZW YRD210 ZB This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there 15 no guarantee that interference will not occur in a particular installation If this equipment does cause harmful Interference to radio or television reception which can be determined by turning the equipment
13. ke side jamb Correct this by increasing the depth of the pocket for the bolt Check for misalignment of bolt and or strike which may be preventing bolt from properly entering the strike With the door open extend and retract the bolt if it is smooth check the strike alignment Bolt does not extend or retract smoothly Bolt and strike are misaligned see above Check the backset of door relative to adjustments already made to bolt Verify proper door preparation and re bore holes that are too small or misaligned Verify keypad wire harness is routed under the bolt see Fig A Verify bolt is installed with correct side up Fig A Keypad numerics are scrolling Remove interior escutcheon and check to ensure that the wire harness lies flat against the back recessed area and is properly routed along the side of the escutcheon and tucked under the plastic cable guide Wire harness tucks under plastic cable guide Cable Guide Harness Clip An ASSA ABLOY Group brand P N AYRD210 INST FUL Rev E ASSA ABLOY Programming Troubleshooting Symptom Suggested Action Lock does not respond door 15 open and accessible Press each keypad button to see if they respond when pressed Check batteries are installed and oriented correctly pola
14. nment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Section 7 1 2 of RSS GEN Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication En vertu des r glements d Industrie Canada cet metteur radio ne peut fonctionner avec une antenne d un type et un maximum ou moins approuv s pour gagner de l metteur par Industrie Canada Pour r duire le risque d interf rence aux autres utilisateurs le type d antenne et son gain doivent tre choisies de facon que la puissance isotrope rayonn e quivalente PIRE ne d passe pas ce qui est n cessaire pour une communication r ussie Section 7 1 3 of RSS GEN This Device complies with Industry Canada License exempt RSS standard s Operation 15 subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cet appareil est conforme avec Industrie Canada
15. ntering a valid PIN code the unit will shut down and not allow operation Default setting is 5 Limit is adjust able from one 1 to ten 10 times Adjustable only when using Network Module with compatible integrated controller P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY OPERATION Register Master PIN Code Before Programming 1 Press the E key to enter Master PIN Code Registration 2 Press the key followed by the Ed key 3 Enter a unique 4 8 digit Master PIN code followed by the key Press the key to enter Master Press the 1 key followed by the Enter the new Master PIN code 4 8 Code Registration digits followed by the key PIN code structure Maximum number of user codes is 250 with Network Module without Network Module maximum is 25 user codes Set Up User Codes User Codes can only be programmed through the Master Code 1 Enter the 4 8 digit Master PIN code followed by the key 2 Press the key followed by the Ed key 3 Press the key followed by the Ed key 4 Enter the User number to be registered 1 25 followed by the 5 Enter 4 8 digit PIN code the User number followed by the key Note When registering User codes the code must be entered with in 20 seconds If time expires no codes are registered and the process must be re started Protect your privacy always shield your PIN code e
16. ntry P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY To reset the lock to factory default see the following Reset Lock to Factory Default The following procedure returns the lock to its factory defaults by deleting all user codes including the Master PIN code and returning all programming features to their original default settings see below 1 Remove the batteries and then remove the interior escutcheon to access the reset button 2 The reset button see image at right is located above the PCB cable connector 3 Hold down the reset button for a minimum of 3 seconds and then reinstall the batteries once the batteries are properly installed release the reset button All features including adjustable settings see below should now be returned to factory default Upon reset Master Code Registration is the only option available and must be performed prior to any other programming of the lock See Operation in this manual for programming instructions Inside Escutcheon Factory Default Settings Settings Factory Default Master PIN Code Registration required Automatic Re lock Disabled Inside Indicator Light Disabled Off One Touch Locking Enabled Audio Enabled Privacy Mode Disabled Automatic Re lock Time 30 Seconds Wrong Code Entry Limit 5 Times Shutdown Time 60 Seconds The M
17. nvenience P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY
18. rity in the battery case Check batteries are in good condition replace batteries if discharged Check to see if cable is fully connected and not pinched Lock does not respond door 15 locked and inaccessible Lock may be in Privacy mode set from inside room Key will grant access Batteries may be completely discharged Use mechanical key to gain entry and replace batteries Unit chimes to indicate code accep tance but the door will not open Check to see if there is another locking device on the door Check the door gaps for any foreign objects between door and frame Check that the cable is firmly connected to the PC board Unit operates to allow access but will not automatically re lock Check to see if Auto Re lock Mode is enabled Disable Auto Re lock Mode to lock the door automatically If low battery indicator is lit see below change batteries PIN codes will not register PIN codes must consist of 4 to 8 digits to register The same PIN code cannot be used for multiple users Registration management of PIN codes is set by the authority of the Master Code Contact the Master user User codes must be entered within 5 seconds or the process will have to be restarted The star O or pound E cannot be used as part of the PIN code Upon entering a PIN code and press ing the star key the lock gives a series of beeps flashes red and blue LEDs seven times and does not unlock
19. ry power is completely lost use the key override Master PIN Code The Master PIN code is used for programming and for feature settings It must be registered prior to programming the lock The Master code will also operate unlock lock the lock Network Module Setting With the optional Network Module installed this setting becomes available through the Main Menu 7 and allows the lock to connect with a network controller One Touch Locking When the latch is retracted activating the keypad will extend the latch during Automatic Re lock duration or when Automatic Re lock is disabled Privacy Mode Button Pressing and holding the Privacy button found below thumbturn for a duration of four beeps deactivates the keypad and because it is set from the inside provides a secure lock for the convenience of the occupant s Shutdown Time The unit will shutdown for a default of sixty 60 seconds time is adjustable from 10 180 seconds and not allow operation after the wrong code entry limit see below has been met When the unit is in Shutdown the Status Indicator flashes RED and BLUE the keypad flashes as well Tamper Alert Audible alarm sounds if attempting to forcibly remove outside lock from door User PIN Code The User code operates the lock Maximum number of user codes is 250 with Network Module without Network Module maximum is 25 user codes Wrong Code Entry Limit After a specified number of unsuccessful attempts at e
20. teries Use feature programming step 7 page 12 for enrollment of the Network Module P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY How to Replace or Install Cylinder 1 Remove cylinder A Remove outside escutcheon from door B Remove rubber gasket C Remove two screws holding plastic guide in place D Remove plastic guide E Remove screw with washer holding cylinder in place visible after plastic guide is removed F Remove cylinder housing by pulling towards the door side of escutcheon Before installing cylinder please be sure you have correct length tailpiece 2 Install new cylinder A Reverse previous steps for removing cylinder Cylinder and tailpiece information Requires addition of Thin Door Kit An ASSA ABLOY Group brand 1 3 8 to 2 thick doors L 3 1 2 88 8mm 2 to 2 1 4 thick doors L 3 3 4 95 3mm Tailpiece T 098 2 5mm W 2 5 2mm T P N AYRD210 INST FUL Rev E ASSA ABLOY PIN CODE MANAGEMENT SAMPLE SHEETS PIN Code Management No Network Module Up to 25 Users Location Door Number Useri 1 User PIN Code P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY PIN Code Management With Network Module Up to 250 Users Duplicate Sheet to record entries Pe S
21. until snug Do not over tighten Tongue Figure 4A Inside of Door Figure 4B P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY CAUTION Position and bend cable using care when assembling to ensure that the cable lies against the back recessed area of the inside escutcheon Use the cable hook Note label on circuit board as shown in Figures 6A amp 6B to prevent binding when installing the escutcheon over the mounting plate Figure 6A 6 Attach cable assembly connector to the inside escutcheon PC board by lining up notches on top of cable connector to slots on PCB connector Fig 6B NOTE Connector should be pressed in firmly using thumbs until completely seated x Figure 6B Route cable as indicated Proper position is indicated by arrows on PCB as in Figures 6A 6B and 6C hole Cable Hook Harness Clip Figure 6C P N AYRD210 INST FUL Rev E An ASSA ABLOY Group brand ASSA ABLOY 8 Install inside escutcheon on inside mounting plate Note the horizontal orientation of the tailpiece Fig 7 as you insert the inside escutcheon thumbturn should be vertical Install and secure using 3 x 8mm 8 32 x 5 16 pan head screws through the inside escutcheon into the mounting
Download Pdf Manuals
Related Search