Hilti 2084262 Use and Care Manual
Contents
1. 8 4 Driving a fastener El WARNING Always observe the safety rules listed in the operating instructions 1 Press the tool against the working surface at right angles 2 Drive the fastener by pulling the trigger 8 5 Cycling the tool El CAUTION Do not use a swinging movement to cycle the tool piston return and cartridge transport The swinging movement may lead to injury or cause damage to the tool NOTE If the cycling action i e pulling out pushing back in is stiff this indicates that the tool needs to be cleaned Service the tool see section 9 3 1 After driving a fastener grip the collar at the nose of the tool between the thumb and forefinger 2 Pull the nose unit forward in the main axis of the tool as far as it will go 3 Then pull the fastener guide all the way back to its original position This movement brings the piston back to its starting position and advances the cartridge strip to the next cartridge The tool is then ready to drive the next fastener 8 6 Unloading the tool O Check that there is no cartridge strip or fastener in the tool If there is a cartridge strip or fastener in the tool pull the cartridge strip up out of the tool by hand from above and remove the fastener from the fastener guide 9 Care and maintenance CAUTION When this type of tool is used under normal operating conditions dirt and residues build up inside the tool and functionally relevant parts are a2. DX 2 Operating instructions Mode d emploi Manual de instrucciones Manual de instru es en fr es pt i 3 ORIGINAL OPERATING INSTRUCTIONS DX 2 powder actuated fastening tool It is essential that the operating instructions are read before the tool is operated for the first time Always keep these operating instructions to gether with the tool Ensure that the operating instructions are with the tool when it is given to other persons Contents 1 Safety instructions 2 General information 3 Description 4 Accessories consumables 5 Technical data 6 Before use 7 Guidelines 8 Operation Dd OS OO BIO 10 9 Care and maintenance 8 10 Troubleshooting 9 11 Disposal 13 12 Manufacturer s warranty tools 13 13 EC declaration of conformity original 13 14 Confirmation of CIP testing 13 15 Health and safety of the operator 14 These numbers refer to the illustrations You can find the illustrations at the beginning of the operating instructions In these operating instructions the designation the tool always refers to the DX 2 powder actuated fastening tool Parts and operating controls 1 Casing 2 Piston guide 3 Base plate 4 Fastener guide Piston 6 Spring clip 7 Catch Annular spring 9 Ball Additional base plate 1 Safety instructions 1 1 Basic information concerning safety In addition to the information relevant to safety given in each of the sec
3. use the piston to push the fastener guide out of the base plate from the front 9 3 2 Checking the piston for wear NOTE Never use a worn or damaged piston and do not tamper with or modify the piston Replace the piston if the piston is broken the piston is badly worn or chipped e g a 90 segment broken away the piston ring is cracked or missing the piston is bent check by rolling the piston on a smooth flat surface 9 3 3 Checking the fastener guide for wear Replace the fastener guide if the tubular section is dam aged e g bent widened cracked or broken 9 3 4 Checking the spring clip for wear Replace the spring clip if it is badly worn bent or widened 9 3 5 Cleaning El El Clean the tool at least once a week or respectively immediately after each period of heavy use after driving approx 3 000 nails Use the appropriate brushes to clean the individual parts 1 Clean the fastener guide and base plate inside and out 2 Clean the piston and piston rings until the parts move freely Clean the piston guide inside and out 4 Clean the inside of the housing o 9 3 6 Lubrication Spray the cleaned parts lightly with the Hilti lubricant spray supplied Use only Hilti lubricant spray or a product of comparable quality 9 3 7 Assembling the tool IE NOTE Handle the small parts carefully They could get lost 1 Fit the fastener guide into the base plate 2 Slide the piston i
4. DANGER Draws attention to imminent danger that will lead to serious bodily injury or fatality WARNING Draws attention to a potentially dangerous situation that could lead to serious personal injury or fatality CAUTION Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property NOTE Draws attention to an instruction or other useful informa tion 2 2 Explanation of the pictograms and other information Warning signs General Warning Warning hot warning explosive surface substances Obligation signs N a Wear a hard Wear ear Wear protective hat protection glasses Symbols Read the operating instructions before use Location of identification data on the tool The type designation and serial number can be found on the type identification plate on the tool Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department Type Generation 01 Serial no 3 Description 3 1 Use of the product as directed The tool is designed for professional use in fastening applications where nails threaded studs and composite fasteners are driven into concrete steel and sand lime block masonry The tool is for hand held use only Modification of the tool is not permitted The tool may not be used in an explosive or flammable atmo
5. specific information can be found in the Hilti Fastening Technology Manual Nail lengths for steel ET Depth of penetration 12 2 mm 2 Ne Nail lengths for concrete ET Depth of penetration 22 mm max 27 mm max 1 8 Operation WARNING The tool can be made ready to fire by pressing the nosepiece against a part of the body e g a hand When the tool is ready to fire fasteners or the piston could be driven inadvertently into parts of the body Never press the tool against parts of the body WARNING The material may splinter or fragments of the magazine strip may fly off when the fastener is driven The user of the tool and other persons in the immediate vicinity must wear suitable eye protection and a hard hat Splintering material presents a risk of injury to the eyes and body CAUTION The fastener driving action is initiated by ignition of a pro pellant charge The user of the tool and other persons in the immediate vicinity must wear ear protectors Exposure to noise can cause hearing loss WARNING Never redrive a fastener This may cause the fastener to break and the tool may jam WARNING Never drive fasteners into existing holes unless this is recommended by Hilti e g DX Kwik CAUTION If the tool has overheated allow it to cool down Do not exceed the recommended fastener driving rate 8 1 Procedure if a cartridge fails to fire If a cartridge fails to fire or misfires always proc
6. Enveloping surface method in anechoic room on reflective surface area in accordance with E DIN EN 15895 DIN EN ISO 3745 and DIN EN ISO 11201 NOTE The noise emissions measured and the associated measurement uncertainty represent the upper limit for the noise values to be expected during the measurements Variations in operating conditions may cause deviations from these emission values 15 2 Vibration Further information about user health and safety can be Total vibration in accordance with 2006 42 EC does not found at www hilti com hse exceed 2 5 m s 14 elias Hilti Corporation LI 9494 Schaan Tel 423 234 21 11 Fax 423 234 29 65 www hilti com Hilti registered trademark of Hilti Corp Schaan W 4344 0714 00 Pos 3 1 Printed in Taiwan 2014 Right of technical and programme changes reserved S E amp 0 2083451 A3
7. bH Zulassung Elektrowerkzeuge Hiltistrasse 6 86916 Kaufering Deutschland 14 Confirmation of CIP testing The following applies to C I P member states outside the EU and EFTA judicial area The Hilti DX 2 has been system and type tested As a result the tool bears the rectangular PTB approval mark showing approval number S 830 Hilti thus guarantees compliance with the approved type Unacceptable defects or deficiencies etc determined during use of the tool must be reported to the person responsible at the approval authority PTB and to the Office of the Permanent International Commission C P 15 Health and safety of the operator 15 1 Noise information Powder actuated fastening tool Type DX 2 Model Serial Caliber 6 8 11 Application Fastening 20 mm 34 laminated wood plywood to concrete C40 with the X U47 P8 Declared measured values of noise characteristics according to 2006 42 EC Machinery Directive in conjunction with DIN EN 15895 Noise power level Lyya 15 101 dB A Emission noise pressure level in the work station 104 dB A Loa 1s Peak sound pressure emission level Loc peak 3 139 dB C 1 2 dB A 2 2 dB A 3 2dB C Operation and set up conditions Set up and operation of the powder actuated fastening tool in accordance with E DIN EN 15895 1 in the semi anechoic test room of M ller BBM GmbH The ambient conditions in the test room conform to DIN EN ISO 3745 Testing procedure
8. e tool to cool WARNING Never attempt to pry a cartridge from the magazine strip or tool Clean the tool and remove any loose cartridges If the tool cannot be disassembled contact your local Hilti Center Fault A cartridge detaches itself from the cartridge strip AN The piston gets stuck in the base material fastener is driven too deeply The fastener is not driven deeply enough The nail bends Concrete spalling Possible cause The fastener driving rate is too high The fastener is too short The fastener has no washer Driving power is too high The fastener is too long Driving power is too low Hard surface steel concrete Hard and or large aggregates in the concrete A rebar is located just below the con crete surface Hard old concrete Hard and or large aggregates in the concrete Remedy Stop using the tool immediately Remove the cartridge strip and allow the tool to cool WARNING Never attempt to pry a cartridge from the magazine strip or tool Clean the tool and remove any loose cartridges If the tool cannot be disassembled contact your local Hilti Center Use a longer fastener Use a fastener with washer for appli cations on wood Use a less powerful cartridge Use a shorter fastener NOTE Observe the min fastener driving depth requirements Obtain a copy of the Fastening Technology Manual from your local Hilti Center U
9. eed as follows Keep the nose of the tool pressed at right angles against the working surface for 30 seconds If the cartridge still fails to fire withdraw the tool from the working surface taking care to avoid pointing it toward your body or toward bystanders Load the next cartridge on the strip by cycling the tool Use up the remaining cartridges on the strip and remove the used cartridge strip from the tool The partly used cartridge strip must then be disposed of appropriately to prevent further use or misuse of any unfired cartridges 8 2 Loading the tool 1 Push the nail head first into the nose of the tool from the front until it is held in place in the tool by the washer on the nail 2 Push the cartridge strip narrow end first into the grip of the tool from below until the full length of the cartridge strip is inside the grip 3 If you wish to use a partly used cartridge strip pull the strip upwards by hand out of the tool slightly until the first unused cartridge is in place in the cartridge chamber 8 3 Setting the power level 1 Select the cartridge power level according to the application to be carried out 2 If you cannot estimate this on the basis of previous experience always begin with the lowest power Select the lowest power level according to the color code 3 Drive a nail If the nail is not driven deeply enough use a more powerful cartridge if necessary or alternatively use a shorter nail
10. ement 16 mm 0 63 Contact pressure 160 N Ambient operating temperature range 15 50 C 5 122 F Recommended maximum fastening rate 450 h 6 Before use 6 1 Checking the tool A WARNING Do not operate the tool when parts are damaged or when the controls do not function correctly If necessary have the tool repaired at an authorized Hilti service center NOTE Read the operating instructions before you operate the tool for the first time Check that no cartridge strip is loaded in the tool If there is a cartridge strip in the tool pull it up out of the tool by hand from above Check all external parts of the tool for damage and check that all controls operate faultlessly Check the piston and spring clip for wear and ensure that the parts have been fitted correctly al 7 Guidelines 7 1 Fastening guidelines These guidelines must be observed at all times NOTE For detailed information please ask your local Hilti sales and service office for a copy of the applicable technical guidelines or national technical regulations 7 1 1 Minimum distances and spacing Minimum distances and spacing when fastening to steel min edge distance 15 mm min spacing 20 mm 4 min base material thickness 3 mm 25 ay min edge distance 70 mm 2 min spacing 80 mm 8 min base material thickness 100 mm 4 7 1 2 Depth of penetration NOTE Examples and
11. ener for timber structures on concrete X FS Fastener for positioning formwork X SW Flexible washer fastener for fastening plastic sheeting and thin insulating materials to concrete and steel X HS X HS W Suspension system with threaded connection X CC Fastening clip for wire hangers X D FB X EMTC Metal conduit clip for fastening electrical conduits or insulated pipes hot or cold in water supply and heating installations X EKB Cable clasp for fastening electric cables flat on ceilings and walls X ECH Bunched cable holder for fastening cables on ceilings and walls X ET Fastener for plastic PVC electric cable trunking X E M W 6 8 Threaded stud for fastenings on concrete and steel Cartridges Cartridge type Color Power level 6 8 11 M red red heavy 4 Accessories consumables NOTE For information about further accessories and fasteners for use with the tool please contact your local Hilti representative Accessories and cleaning set Designation Cleaning set Hilti lubricant spray spare parts pack operating instructions spall guard Standard accessories Designation Piston base plate piston guide fastener guide spring guide catch annular spring 5 Technical data Right of technical changes reserved Tool DX 2 Weight 2 4 kg 5 29 Ib Dimensions L x W x H 345 mm 13 58 x 50 mm 1 97 x 157 mm 6 18 Maximum fastener length 62 mm 2 Cartridges 6 8 11 M 27 cal short green yellow red Contact mov
12. hen operating a direct fastening tool Don t use the tool when you are tired or under the influence of drugs alcohol or medication Stop using the tool if you experience pain or do not feel well A moment of inattention while operating the tool may result in serious personal injury b Avoid unfavorable body positions Make sure you work from a safe stance and stay in balance at all times c Wear non skid shoes d Never point the tool toward yourself or other per sons e Never press the nosepiece of the tool against your hand or against any other part of your body or other person s hand or part of their body f Keep other persons especially children away from the area in which the work is being carried out g Keep the arms slightly bent while operating the tool do not straighten the arms h Observe the information printed in the operating in structions concerning operation care and mainte nance 1 1 4 Use and care of powder actuated fastening tools a Use the right tool for the job Do not use the tool for purposes for which it was not intended Use it only as directed and when in faultless condition b Never leave a loaded tool unattended c Store unused cartridges and tools currently not in use in a dry place where they are not exposed to high temperatures d Transport and store the tool in a toolbox that can be secured to prevent unauthorized use e Always unload the tool remove cartridges and fas
13. l is damaged Build up of combustion residues Build up of combustion residues Build up of combustion residues Build up of combustion residues The tool is not cycled The cartridge has already been fired The tool was not pressed fully against the working surface The tool is badly fouled with dirt and The piston is damaged Remedy Service the tool See section 9 3 Servicing the tool Service the tool See section 9 3 Servicing the tool Service the tool See section 9 3 Servicing the tool Service the tool See section 9 3 Servicing the tool See section 8 5 Cycling the tool El Transport the used cartridge by cy cling the tool or pull the cartridge strip through manually to the next position Press the tool fully against the work ing surface Service the tool See section 9 3 Servicing the tool Clean the tool See section 9 3 Servicing the tool Check the piston and replace it if nec essary See section 9 3 2 Checking the pis ton for wear If the problem persists contact your local Hilti Center Fault Misfire Less than normal sound The fastener is only partly driven into the base material HG The cartridge strip doesn t ad vance A gt The cartridge strip cannot be removed x 1 A cartridge doesn t fire The cartridge strip melts a lt I lt Rec 10 P
14. le for thin steel base material Steel with a thickness of less than 3 mm is not suitable as a base material for DX fastening Use a more powerful cartridge Use a shorter nail Use a nail with a higher application limit Use a more powerful system e g DX 460 Use a less powerful cartridge Use a nail with a top hat Use a nail with a washer 11 Disposal Most of the materials from which Hilti tools or appliances are manufactured can be recycled The materials must be correctly separated before they can be recycled In many countries Hilti has already made arrangements for taking back old tools and appliances for recycling Ask Hilti customer service or your Hilti representative for further information 12 Manufacturer s warranty tools Please contact your local Hilti representative if you have questions about the warranty conditions 13 EC declaration of conformity original Designation Powder actuated fasten Hilti Corporation Feldkircherstrasse 100 ing tool FL 9494 Schaan Type DX 2 A 4 Lif Year of design 2014 0 eum Lars Taenzer Head of BU Direct Fastening Norbert Wohlwend Head of Quality amp Processes Manage We declare on our sole responsibility that this product complies with the following directives and standards t 2006 42 EC 201 1 65 EU BU Direct Fastening BU Direct Fastening 02 2014 02 2014 Technical documentation filed at Hilti Entwicklungsgesellschaft m
15. lso subject to wear Reg ular inspections and maintenance are thus essential in order to ensure reliable operation We recommend that the tool is cleaned and the condition of the pis ton checked at least daily when the tool is subjected to intensive use and at the latest after driving 3 000 fasteners WARNING All cartridges must be removed from the tool Check to ensure that no fastener is present in the fastener guide before carrying out maintenance or repairs CAUTION The tool may get hot during use You could burn your hands Wear protective gloves when carrying out care and maintenance Allow the tool to cool down 9 1 Care of the tool Clean the outside of the tool at regular intervals with a slightly damp cloth WARNING Do not clean with a spray or pressure washer Do not permit foreign objects to enter the interior of the tool 9 2 Maintenance Check all external parts of the tool for damage at regular intervals and check that all controls operate faultlessly Do not operate the tool if parts are damaged or when the controls do not function faultlessly If necessary the tool should be repaired by Hilti Service Use the tool only with the recommended cartridges and power settings Use of the wrong cartridges or use of excessively high power settings may lead to premature failure of parts of the tool CAUTION Dirt and residues in DX tools contain substances that may be hazardous to your health Do not inhale dust o
16. nto the piston guide as far as it will go 3 Fit the base plate with the fastener guide onto the piston guide NOTE The slots in the base plate and piston guide must be in alignment with each other 4 Press the spring clip into the recess 5 Guide the assembly into the tool NOTE The slot in the piston and fastener guide must be in alignment with the opening for the catch 6 Press the catch into the opening and turn the annular ring back over the catch NOTE The catch can be removed when in the swiveled out position and subsequently reinserted 9 3 8 Checking After carrying out care and maintenance check that all protective and safety devices are fitted and that they function faultlessly NOTE The tool can be checked as follows to determine whether it is ready to fire Press the nose of the un loaded tool i e no cartridges or fastener in the tool firmly against a hard surface and pull the trigger A clearly heard click from the trigger mechanism indicates that the tool was ready to fire 10 Troubleshooting WARNING The tool must be unloaded before taking any steps to remedy faults Fault Possible cause Higher force required to cycle the tool Higher force required to press the tool against the surface Trigger resistance increases The cartridge strip is difficult to remove The tool cannot be fired Tool jams residues The too
17. ol or machine may become live for example when an electric cable is damaged accidentally Use the fasteners only within the recommended temperature range Always observe the informa tion given in the operating instructions Plastic parts can break and splinter at low temperatures 1 1 6 Mechanical safety precautions Use only fasteners of a type approved for use with the tool Do not tamper with or modify the tool or parts of it especially the piston 1 1 7 Thermal safety precautions a If the tool has overheated allow it to cool down Do not exceed the recommended fastener driving rate b Do not dismantle the tool while it is hot Allow the tool to cool down c The tool must be allowed to cool down if the plastic cartridge strip begins to melt 1 1 8 Danger of explosion a Use only cartridges of a type approved for use with the tool b Remove the cartridge strip from the tool carefully c Never attempt to pry a cartridge from the mag azine strip or tool Never attempt to open a car tridge d Store unused cartridges in a secure place where they are not exposed to dampness or excessively high temperatures 1 1 9 Personal protective equipment a a E The user and any other persons in the vicinity must wear suitable eye protection a hard hat and ear protection while the tool is in use or when remedying a problem with the tool 2 General information 2 1 Safety notices and their meaning
18. ossible cause The piston was in the wrong position Bad cartridges The cartridge strip is damaged The tool is badly fouled with dirt and residues The tool is damaged The tool has overheated Bad cartridge The tool needs to be cleaned The tool is pressed against the work ing surface for too long before firing The fastener driving rate is too high Remedy Remove the cartridge strip and cycle the tool See section 8 5 Cycling the tool Change the cartridge strip use a dif ferent dry package if necessary If the problem persists service the tool See section 9 3 Servicing the tool Change the cartridge strip Clean the tool See section 9 3 Servicing the tool If the problem persists contact your local Hilti Center Allow the tool to cool down Subsequently carefully remove the cartridge strip from the tool WARNING Never attempt to pry a cartridge from the magazine strip or tool If the problem persists contact your local Hilti Center Pull the cartridge strip through to the next cartridge Service the tool WARNING Check that the correct cartridges are used and that they are in faultless condition See section 9 3 Servicing the tool If the tool cannot be disassembled contact your local Hilti Center Fire the tool sooner after pressing it against the working surface Remove the cartridge strip Stop using the tool immediately Remove the cartridge strip and allow th
19. r dirt from cleaning Keep the dust or dirt away from foodstuffs Wash your hands after cleaning the tool Never use grease for the maintenance lubrication of parts of the tool This may lead to malfunctions Use only Hilti lubricant spray or a product of comparable quality 9 3 Servicing the tool Service the tool if fastener driving power is found to be inconsistent if cartridges misfire or if parts of the tool no longer move or operate smoothly and easily In other words the required contact pressure increases trigger resistance increases the cartridge magazine strip can only be removed with a degree of difficulty or the cycling action becomes stiff 9 3 1 Disassembling the tool CAUTION When removing the spring clip from the base plate the spring clip may jump off the base plate very suddenly Take care to avoid injury to yourself or other persons Hold the base plate so that the spring clip if it jumps off tends to jump towards the floor 1 Lift the annular ring with a small prybar or a nail and turn 2 Pull the catch back and remove it 3 Pull out the insert 4 Remove the spring clip Use a suitable tool for this purpose e g small prybar or nail 5 Pullthe base plate complete with the fastener guide off the piston guide 6 Pull the piston out of the piston guide 7 Allow the fastener guide to slide out of the base plate toward the rear NOTE If the parts of the tool tend to stick due to carbon build up
20. se a more powerful cartridge Use a more powerful cartridge Use a more powerful cartridge Use the DX 460 with DX Kwik predrilling Use a shorter nail Use a nail with a higher application limit Use the DX 460 with DX Kwik predrilling Drive the fastener at a different posi tion Use a shorter nail Use a more powerful cartridge Use the DX 460 with DX Kwik predrilling 11 Fault Damaged nail head The nail doesn t penetrate deeply enough air The nail doesn t hold in the base material Nail breakage i The head of the nail punches through the material fastened sheet metal 1 12 Possible cause Driving power is too high Application limit exceeded very hard material The piston is damaged Driving power is too low Application limit exceeded very hard material The system is unsuitable The piston was in the wrong position Thin steel base material Driving power is too low Application limit exceeded very hard material The system is unsuitable Driving power is too high Remedy Use a less powerful cartridge Use a nail with a higher application limit Change the piston Use a more powerful cartridge Use a nail with a higher application limit Use a more powerful system e g DX 460 Remove the cartridge strip and cycle the tool See section 8 5 Cycling the tool El Use a different cartridge Use a nail suitab
21. sphere unless it has been approved for use under these conditions To reduce the risk of injury use only genuine Hilti fasteners cartridges accessories and spare parts or those of equivalent quality Observe the information printed in the operating instructions concerning operation care and maintenance The tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed The tool may be operated serviced and repaired only by trained personnel This personnel must be informed of any special hazards that may be encountered As with all powder actuated fastening tools the tool cartridges and fasteners form a technical unit This means that trouble free fastening with this system can be assured only if the Hilti fasteners and cartridges specially manufactured for it or products of equivalent quality are used The fastening and application recommendations given by Hilti apply only when these conditions are observed 3 2 Range of fasteners available for various applications Fasteners Ordering designation Application X U High strength nail for fastening on high strength steel and concrete in a wide range of applications X C Standard nail for fastening on concrete X S Standard nail for efficient fastening on steel X CT Easily removable nail for fastening formwork temporarily on concrete X CR Stainless steel nail for fastening in damp or corrosive surroundings X CF Special fast
22. teners before cleaning before maintenance before work breaks and before storing the tool f When not in use tools must be unloaded and stored in a dry place locked up or out of reach of children g Check the tool and its accessories for any dam age Guards safety devices and any slightly worn parts must be checked carefully to ensure that they function faultlessly and as intended Check that moving parts function correctly without stick ing and that no parts are damaged All parts must be fitted correctly and fulfill all conditions neces sary for correct operation of the tool Damaged guards safety devices and other parts must be repaired or replaced properly at a Hilti service center unless otherwise indicated in the operat ing instructions h Pull the trigger only when the tool is fully pressed against the working surface at right angles i Always hold the tool securely and at right angles to the working surface when driving in fasteners This will help to prevent fasteners being deflected by the working surface Never redrive a fastener This may cause the fas tener to break and the tool may jam k Never drive fasteners into existing holes unless this is recommended by Hilti Always observe the application guidelines m Use the spall guard when the application permits n Never pull the fastener guide or the fastener back by hand as this could make the tool ready to fire This could cause a fastener or the pis
23. tions of these operating instructions the following points must be strictly observed at all times 1 1 1 Using cartridges Use only Hilti cartridges or cartridges of equivalent quality Use of cartridges of inferior quality in Hilti tools may lead to a build up of unburned powder which may explode and cause sever injuries to operators and bystanders Cartridges must fulfill one of the following minimum re quirements a The applicable manufacturer must be able to verify successful testing in accordance with the EU stan dard EN 16264 or b The cartridges must bear the CE conformity mark mandatory in the EU as of July 2013 NOTE All Hilti cartridges for powder actuated tools have been tested successfully in accordance with EN 16264 The tests defined in the EN 16264 standard are system tests carried out by the certification authority using specific combinations of cartridges and tools The tool designa tion the name of the certification authority and the system test number are printed on the cartridge packaging Please refer to the example at www hilti com dx cartridges packaging 1 1 2 Requirements to be met by users a The tool is intended for professional use b The tool may be operated serviced and repaired only by authorized trained personnel This per sonnel must be informed of any special hazards that may be encountered 1 1 3 Personal safety a Stay alert watch what you are doing and use common sense w
24. ton to be driven into a part of the body 1 1 5 Work area safety IN A Ensure that the workplace is well lit Operate the tool only in well ventilated working areas Do not attempt to drive fasteners into unsuitable materials Materials that are too hard e g welded steel and cast iron Materials that are too soft e g wood and drywall panel gypsum board Materials that are too brittle e g glass and ceramic tiles Driving a fastener into these materials may cause the fastener to break shatter or to be driven right through Never attempt to drive fasteners into materials such as glass marble plastic bronze brass copper rock insulation material hollow brick ceramic brick thin sheet metal lt 3 mm s cast iron or cellular concrete Before driving fasteners check that no one is present immediately behind or below the working surface Keep the workplace tidy Objects which could cause injury should be removed from the work ing area Untidiness at the workplace can lead to accidents Keep the grips dry clean and free from oil and grease Do not use the tool where there is a risk of fire or explosion unless it has been specially approved for use under these conditions Concealed electric cables or gas and water pipes present a serious hazard if damaged while you are working Accordingly check the area in which you are working beforehand e g using a metal detector External metal parts of the to
Download Pdf Manuals
Related Search