Fire Sense 02678 Use and Care Manual
Contents
1. When heater is not in use for an extended period of time store in a covered location that is dry and out of the weather Make sure the heater is stored in a location that is out of the way of people and pets that may accidentally knock the heater over or damage the appliance Before storing the heater make sure the electrical cord is coiled and out of the way When storing ALWAYS lower the telescopic pole to its lowest level This will make it easier to store and reduce the risk of any accidental tipping over of the heater Maintenance Your Infrared Heating System is virtually maintenance free A minute to wipe down exposed surfaces is all it takes to maintain your heater Head unit and shield Use a non abrasive cleaner and a soft cloth to wipe off debris and dirt from the exposed surfaces NEVER spray liquids or cleaners into the housing area where the halogen lamp is located Do not try to disassemble of clean the inner cavity where the halogen lamp is located For any maintenance on the head unit please call the toll free customer service hotline Telescopic pole and curved arm components These can easily be wiped clean using a non abrasive cleaner and a soft cloth Base with wheel assembly Use non abrasive cleaner and a soft cloth Any scratches chips or rust spots can be touched up using an exterior matte finish black paint 10 Halogen Lamp Replacement Contact the toll free customer hotline to order approved replacement l2. automatically should the unit be accidentally knocked over or tilted past 15 degrees To reset unplug the unit from wall outlet reposition on a flat level surface and plug in again 17 SAVE THESE INSTRUCTIONS for future reference Assembling Your Heater Before beginning assembly be sure to read and familiarize yourself with the overall assembly process and instructions in this manual It may be helpful to have someone assist you with the assembly You will need the following tools NOT INCLUDED 2 or 3 Philips Screwdriver or standard slotted screwdriver Adjustable Wrench Make sure you complete assembly on a clean level preferably carpeted location A flat piece of cardboard will also work for assembly Unpack and identify all components listed on page 3 of this manual and lay them out on the carpeted floor or piece of cardboard and then follow the steps below STEP 1 Loosen and remove the top 2 screws on each side of the head unit Part 1 and attach the angle adjustment handle included with Part 1 as shown in Figure 1 FIGURE 1 Tighten the screws as shown in Figure 2 FIGURE 2 STEP 2 Using mounting bracket Part 2 thread entire electrical cord through the mounting bracket as shown in Figure 3 FIGURE 3 STEP 3 Using 4 threaded bolts and lock washers attach mounting bracket Part 2 to head unit Part 1 as shown in Figure 4 FIGURE 4 STEP 4 Align tilt switch black box
3. Off push in the switch Next extend all 3 telescopic sections to their maximum extended length Release clamp levers and pull up on each of the sectional steel tubes until each tube stops Then push in clamp levers to secure sections in place Adjust the tension knobs as needed to maintain height position Step 2 The Infrared Heating System comes equipped with a heavy duty 16 3 gauge wire Grounded outlel Dox cover and grounded plug This appliance must be used with an outlet that has been installed and grounded in accordance with local codes and ordinances Make sure the heater is connected to an outlet having the same configuration as shown in the figure shown to the right DO NOT use an adapter with this product Check with a licensed electrician if the grounding instructions are not understood completely or if the wall outlet does not match the plug Step 3 Your Mojave Sun Infrared Heating System is ready to enjoy Plug the appliance in and enjoy the warmth Specifications Model 02117 60694 02678 Voltage 120 volts Amps 12 5 amps Wattage 1500 watts Lamp Type Quartz Halogen Minimum Operational Height 8 ft 2 in 98 in Assembled Weight 53 Ibs Head Unit Dimensions AS amp R22 Heater Assembled Dimensions 22 diameter base 93 height Storage Always UNPLUG the unit when not in use Once the head unit has completely cooled store the heater with the protective vinyl cover on the head unit
4. over Do not run cord under carpeting Do not cover cord with throw rugs runners or similar coverings Arrange cord away from traffic area and where it will not be tripped over To disconnect heater switch to OFF position push in switch located on head unit and then remove plug from electrical outlet 10 Connect to properly grounded outlets only Important Instructions 11 Do not insert or allow foreign objects to enter any ventilation or exhaust opening doing so may cause an electrical shock or fire or may damage the heater 12 To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked 13 A heater has hot and sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored 14 Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electrical shock or injury to persons 15 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire However if you must use an extension cord use either a 12 gauge or 14 gauge wire which is rated not less than 1900 watts The recommended length for a 14 gauge is 0 50 feet but if you must use a longer cord use a 12 gauge NO LONGER than 100 feet This unit comes equipped with a Safety Tilt Switch mechanism Power will shut off
5. Distributed by Well Traveled Living Amelia Island FL 32034 Web www wtliving com Email cservice welltraveled net A Mojave fix Sun X Owner s Manual Models 02117 60694 02678 INFRARED HEATER POLE SET READ amp SAVE these instructions Carefully read and review before attempting to assemble install operate or maintain this product Observe all safety instructions and information FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY Kor Residential Use Only Important Notice Do not return to place of purchase Please contact our Toll Free Hotline at 1 866 985 7877 for customer service and warranty issues SAVE THESE INSTRUCTIONS Safety Guidelines Read this manual carefully to become knowledgeable about your heater and how to use it properly To help recognize this information observe the following symbols DANGER A WARNING Indicates a potentially hazardous situation which if Indicates a potentially hazardous situation if not not avoided WILL result in serious injury or death avoided COULD result in serious injury or death 4 CAUTION NOTICE Indicates a potentially hazardous situation which if Indicates important information that if not followed not avoided MAY cause moderate injury or damage to may cause damage to the equipment the equipment DANGER 1 i j Risk of Fir
6. amp assembly 5 Using gloves gently re insert connection ends of the NEW lamp assembly into the friction clips 4 Pull apart the clips slightly and gently push the connectors into place Do not allow the metal clips to touch the lamp tube The clips should be about at the center point of the end connectors 6 Re install the safety grill fits along grooves in housing body then re insert the vent panels by gently pushing the end clips into housing body Align clip ends close to the lamp end connectors and push into place Re attach end plates making sure the side with beveled holes faces out 5 lamp assembly Lamp Tube Clip ends must be NY aligned as Close to end connectors of lamp tube when installed Do NOT allow to touch tube lamp itself Using gloves gently re insert connector ends of the NEW Meta friction chps lamp assembly into the friction Push apart siigtly a eon clips see 4 Pull apart the lamp tube end clips slightly and gently push the connectors into place Do not allow the meta clips to touch the actual lamp tube The clips should be about at the center point of the end connectors when a 3 wire ead a re assembied OO Front Veal Pane Remove amp Replace ENTIRE Lamp assembly including lamp end connectors amp wire lead NOTE do NOT allow any metal to contact actual lamp tube 11 Troubleshooting Problem Unit fails to turn on Telescopic pole slips down Telescopic pole is u
7. amps and parts Use ONLY approved original equipment and replacement halogen lamps to ensure safe proper and maximum output operation of your heater NOTE Do NOT touch the new halogen lamp with your bare fingers Oils from your hand could reduce the life of the lamp by causing a heat spot We recommend using clean cotton or plastic gloves to handle the lamp A clean paper towel will also work MAKE SURE THE HEATER IS TURNED OFF AND DISCONNECTED FROM THE ELECTRICAL OUTLET BEFORE YOU BEGIN TO REPLACE THE HALOGEN LAMP 1 Be sure the heater is unplugged from the wall outlet Remove the head unit assembly from the telescopic pole 2 Remove 8 screws from each end of the head unit and pull off end plates 2 Note the placement of the 2 small sheet metal screws on each end plate Also note end plate side with beveled holes faces outward when re assembled 3 Pull out and remove the left and right front air vent panels and protective wire grill 3 Note the position of end clips on vent panel They must be aligned as close to the end connectors of lamp tube as possible when re assembled Pull or push into place as needed DO NOT allow metal parts to touch the actual lamp tube when re assembled 4 Gently pull out entire old lamp assembly from the clips at the terminal connection ends 4 amp 5 Slide and lift the connection ends out from the friction clips by gently pushing apart the clips Unscrew wire leads from terminal Remove entire old l
8. e There is always a risk of fire when working with a heater Keep it away from flammable liquids and any material that could easily catch fire 2 j Risk of Fire If the heater falls this unit might start a fire 3 dad Hot or Burn Hazard This unit may be hot at any time during its use especially around the head and heating element G 4 Electrical Hazard Disconnect all electric power before working on the unit There is a chance of electric shock if you work on this unit with it still plugged into the wall A cord has been damaged Electric Shock This unit uses electricity to operate Do not use this heater around water or if the CAUTION e Improper treatment of the heater can damage it and also shorten its life span e To prevent electrical shock follow electrical plug requirements on page 9 of this manual This appliance MUST be grounded When using outdoors we recommend using a certified GFI Ground Fault Interrupt outlet to protect against electrical shock All installations must be in accordance with I E E safety regulations or the equivalent Avoid the use of an extension cord with this appliance Do not place any objects such as furniture papers clothing or curtains closer than 3 feet to the front and sides of the heater CAUTION PARTS LIST 1 IR Head unit w Protective Shield with Pre installed Tilt Switch safety cut off On Off Switch PULL for ON PUSH for OFF Angle Adjustm
9. ent Bar 1500 Watt quartz halogen bulb Swivel Bracket 12 foot 16 3 grounded electrical cord 2 Mounting Bracket attaches head unit to telescopic pole 3 Curved Upper Arm 4 Inner support tube section for telescopic body 5 Telescopic Body adjustable 6 Base connection pole section 7 Support Collar w Flange for Telescopic Body 8 Base Assembly w wheels 9 Protective vinyl cover for head unit 10 Hardware packet 19 threaded bolts and lock washers 2 small threaded screws w flat washers 1 nut w flat washer and lock washer os Read all instructions before using this heater This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Keep combustible materials such as furniture pillows bedding papers cloths and curtains at least 3 feet 0 9m from the front sides and rear of the heater DO NOT leave heater unattended Extreme caution is necessary when any heater is used by or near children or disabled persons and whenever the heater is left operating and unattended Always unplug heater when not in use Do not operate any heater with a damaged cord or plug if the heater malfunctions or has been dropped or damaged in any manner Return heater to authorized service facility for repair Can be used indoors or outdoors Operate 3 feet 0 9m from people or objects Never operate heater near water or where it can be knocked
10. let to protect against electrical shock ALL installations must be in accordance with I E E safety regulations or equivalent Avoid the use of an extension cord with this appliance If one is used it must meet the requirements as outlined in 15 Important Instructions on page 4 of this manual Do not place any objects such as furniture papers clothing or curtains closer than 3 feet to the front top or sides of this heater ALWAYS unplug the heater when it is not in use For optimal performance and safety concerns we HIGHLY recommend that the Infrared Heating System be operated at a minimum of 98 in height or the maximum extended length of the telescopic body sections You should only lower the height of the unit for storage purposes when it has completely cooled and is not in operation To adjust the IR telescopic body Pull up on the release levers of the tightening clamps and adjust tension using the tension knobs Raise and lower the telescopic sections and or swivel Lever clamps znt nd adj to desired position and then push in clamp levers to secure DO NOT nie over tighten tension knobs There should only be a moderate amount of tension to maintain the telescopic position of your heater Step 1 Before turning on your Infrared Heating System check to make sure the On Off switch located on the tilt switch black box of the head unit is pulled OUT or in the ON position note to turn the heater
11. nsteady Telescopic pole will not adjust Head unit is loose or unsteady Head unit is hard to adjust Smoke appears from head unit Weak output from halogen lamp Solution Check electrical plug connection at wall outlet for a complete snug fit Check to make sure the On Off switch located on tilt switch is pulled OUT or in the On position Check GFI and reset circuit breaker if needed If unit is plugged into a wall outlet wired to an On Off switch make sure switch is in On Position Reset safety tilt switch Unplug unit from wall outlet and re position on flat level surface Plug heater back into outlet Damaged halogen bulb Call customer service hotline Tighten black tension knobs on clamp collars Tighten screws on support collar at base Electrical cord may be kinked Gently pull end of cord until taut Tighten screws on curved upper arm mounting bracket Loosen connecting bolts nuts at adjustment bracket Unplug IMMEDIATELY and call customer service hotline Life span of lamp has been reached or damaged lamp Call customer service hotline for assistance NOTE This product comes with a limited one year warranty After the warranty period you may purchase replacement bulbs from www patiomarket com at the lowest cost available 12
12. on head unit Part 1 to threaded holes on mounting bracket Part 2 and insert small screws with flat washers as shown in Figure 5 FIGURE 5 STEP 5 Thread electrical cord through curved upper arm Part 3 and attach with 4 threaded bolts and lock washers as shown in Figure 6 FIGURE 6 STEP 6 Insert inner support tube Part 4 inside telescopic body Part 5 as shown in Figure 7 Tighten clamp collar as shown FIGURE 8 in Figure 8 FIGURE 7 STEP 7 Thread electrical cord through inner support tube and telescopic body as shown in Figure 9 and affix curved upper arm and inner support tube with one threaded bolt and lock washer as shown in Figure 10 FIGURE 9 STEP 8 Thread electrical cord through base connection pole section Part 6 and insert 4 threaded bolts and lock washers as shown in Figurel1 12 and 13 FIGURE 11 FIGURE 12 FIGURE 13 STEP 9 Mount support collar flange Part 7 to base assembly with wheels Part 8 as shown in Figure 14 and secure with flat washer lock washer and 3 4 bolt as shown in Figure 15 FIGURE 14 FIGURE 15 STEP 10 Carefully lift pole and head unit assembly and insert lower end of pole into support collar flange Part 7 as shown in Figure 16 Secure with 6 threaded bolts and lock washers FIGURE 16 OPERATING INSTRUCTIONS This appliance MUST be grounded When using outdoors we recommend using a certified GFI Ground Fault Interrupt out
Download Pdf Manuals
Related Search