Aquverse A6500-K Installation Guide
Contents
1. Cooler Troubleshooting What To Do If Cooler Is Not Dispensing any Water Confirm that cooler is not frozen by checking inside water tank and determining if water is frozen If frozen unplug the water cooler and let thaw then proceed to the next step If your cooler is not frozen skip ahead to step 3 Check faucets to determine if water is blocked by any obstructions STEP 1 Only if your cooler has frozen turn the cold water thermostat down by turning a 1 4 turn counter clockwise Check that cold water thermostat is not turned to the off position picture shows thermostat in factory set ON position The OFF position would be a 1 3 turn counter clockwise If compressor is not functioning call 1 866 872 5722 to receive NO IMAGE AVAILABLE additional support Determine whether the compressor is working by putting your ear close to the top of the cooler if you hear silence the compressor is not Turn the thermostat a 1 3 turn clockwise to resemble the picture shown working if you hear a humming noise the compressor is working NO IMAGE AVAILABLE Cooler is dispensing water but it is not Hot NO IMAGE AVAILABLE NO IMAGE AVAILABLE Water Is Leaking NO IMAGE AVAILABLE STEP 1 Check the back of the cooler and make sure the hot tank switch is in the on position If hot tank switch is on then you will need to reset the hot tank this can be tripped to the off positi2. cooler Push the cabinet cover down and pull towards you Attach the new filter to filter head by pushing in and turning to the right until it stops Place the bottom of the cabinet cover over the plastic L shaped clips at the bottom of the cooler and press down gently Push the top of the cabinet cover into place and let slide up naturally and click into position STEP 4 STEP 5 TURN OFF WATER Insert the previously removed screw into the bottom of the cabinet Remove the attached filter by turning to the left until it stops cover Pull down gently on the filter until it is removed Re attach the drip tray by pushing in For any needed assistance please call 1 866 872 5722 6 dals
3. times during installation To find the Aquverse warranty please go to www aquverse com Cooler Set Up Filter Specifications First Steps Determine where your cooler is going to be located and place it close to the determined area This drinking water system must be maintained in accordance with the manufacture s instructions see instructions that are provided with filter DO NOT PLUG IN A professional licensed plumber can perform the install or you can obtain the following items at your local hardware store Maximum PSI 10 125 psi Capacity 1500 gallons Temperature 35 100 F Attaching Filter Re attaching Front Cabinet Remove the drip tray by pulling towards you pene B x the bottom of the cooler and press down gently Push the top of the cabinet cover into place and let slide up naturall Remove the screw located behind the drip tray p p o p o y and click into position Insert the previously removed screw into the bottom of the cabinet Push the cabinet cover down and pull towards you p y cover Attach filter to filter head by pushing in and turning to the right until it stops S i Re attach the drip tray by pushing in Locate Water Source WARNING YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES A water source looks like this It can be typically found underneath the closest sink to were you would like to place your cooler Locate the cold water source Make sure that t
4. A6500 Aquverse Water Cooler Installation and Troubleshooting Instructions WARNING YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES FOR INSTALLATION OR THE WARRANTY WILL BE VOIDED MQUVERSE Commercial Grade For any NECdEd Assistante please rall 178008729722 If you do not own the property where the unit will be installed you need to contact the owner and obtain approval before you install your cooler If you are not comfortable with the installation procedure it is Wa arning do not plug water cooler in until water line is in place and dispensing water l recommended to have a professional licensed plumber complete the install for you through the faucets WARNING Do not use a saddle valve for installation or the warranty will be voided WARNING This product is intended for indoor use only Outside temperatures can cause damage to all systems Please use only inside your home or office Items You Need Angle stop fitting size depends on your water source adaptable fitting provided in water line kit z8 Very sharp pair of scissors or a very sharp knife to cut tubing Adjustable crescent wrench a SS Zip Ties provided in water line kit Quick connect 2 sided coupler for poly line provided in water line kit 9 na a Phillips head screw driver Poly Tubing provided in water line kit Drill with a 3 8 bit Water filter Safety Glasses Wear these at all
5. aches room temperature note that water is going to be hot when you begin draining Remove top cover of cooler Remove the float valve from the top of the cold water tank not the position as you will need to re install when cleaning is completed NO IMAGE AVAILABLE Fill the cold water tank with approximately four glasses of water Drain this water through the cooler by opening the cold water faucet NO IMAGE Fill the cold water tank again with approximately four glasses of water AVAILABLE Drain this water through the cooler by opening the hot water faucet this may take more time then through the cold water faucet as done previously Insert the cleaned baffle back into the cold water tank Remove the drain plug from the rear of the cooler water will drain out of the cooler immediately so you will need a bucket or receptacle to catch the water Remove the baffle from the cooler and clean with a clean dish towel and water do not use bleach or any cleaners you may use a small amount of soap if desired Clean the cold tank with a clean dish towel and water do not use bleach or any cleaners you may use a small amount of soap if desired Install the float valve back to its original placement as noted before Install the to cover of cooler back in its original position Replacing Your Water Filter Remove the drip tray by pulling towards you Remove the screw located at the bottom of the cabinet on the front of the
6. he water source you will work with is connected to the NO IMAGE cold faucet on you sink by a water line hose The cold faucet can be To confirm you are using the cold water please shut off the water source NO IMAGE AVAILABLE determining which faucet is the cold faucet and connecting to that water valve and turn on your cold water faucet No water should come out AVAILABLE line hose Confirm Your Water Source Is Off Drain the water from the faucet by turning on the hot and cold faucets NO IMAGE Turn the valve clockwise to shut of the water 7 until no water is running AVAILABLE Installing Water Line Kit Run tubing from water source to cooler If water source is located in a cabinet then you will need to drill a small 3 8 inch hole into the front corner to run the tubing underneath the cabinet Unscrew the cold water line hose from the shut off valve you will have a few ounces of water remaining in the hose that will drip out Attach the angle stop to the shut off valve if the fittings connect correctly Use the Water Line Kit clips to affix the tubing underneath the cabinet NOIMAGE skip the next step alongside kick plate or along wall to help keep out of sight AVAILABLE Determine if you have excess waterline running from you water source Attach the cold water line hose to the angle sto i j and if so cut the poly tubing to the correct length Connect the two sided quick connect to the water line running out of I
7. nsert water line kit tubing into quick connect on angle stop the bottom back corner of you water cooler Run tubing from water source to cooler If water source is located in a T cabinet then you will need to drill a small 3 8 inch hole into the front corner to run the tubing underneath the cabinet Connect the tubing into the two sided quick connect provide in the waterline kit When finished with the above steps you should have tubing running from the angle stop that is attached to the water shut off valve water source to the filter Then tubing from the filter into the cooler Wait a minimum of 30 minutes after you turn on the water source before plugging in filter Flushing the Filter You must flush water through the filter to wash excess carbon out before There is no danger in drinking the water with the carbon residue ee drinking this is commonly referred to as priming the filter and is discoloring the liquid however for the freshest tasting and looking required water it is beneficial to flush the system NO IMAGE To do this please flush two gallons approximately 10 glasses of water ANAIARI through the cooler until the water is clear in color Begin Using Your Cooler WARNING YOU MUST OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES You may begin to use the cooler immediately however it can take approximately 1 hour for the cold tank and hot tank to take effect and chill or heat the water in your cooler
8. on much like a circuit breaker if the cooler is plugged in before water is filled into the tank Reset the hot tank by first unplugging the water cooler then proceed to the next steps Identify the source of the leak i e internal faucets or top Top check if the faucets are the source of the leak you will need to remove the faucet cover by pulling down and the out If the faucets are the source of the leak check to make sure the faucets have been screwed on completely If still leaking drain the cooler of water and remove the faucets and make sure the gaskets around the water spigots are in good condition If the leak is internal please contact customer service at 1 866 872 5722 Turn the cooler around so you are facing the back wire caged portion of the cooler Locate the hot tank through the back cage and then locate the hot tank reset button on the right side of the hot tank Using a chopstick or screwdriver depress the hot tank reset button water should be hot in 30 minutes time see figure below which pictures hole used to access hot tank reset button If leaking is occurring from the nozzle of the faucets please contact customer service at 1 866 872 5722 for replacement NO IMAGE AVAILABLE NO IMAGE AVAILABLE Y dials Cleaning Your Water Cooler NO IMAGE AVAILABLE NO IMAGE AVAILABLE Turn the water source off Unplug cooler Drain water out of the hot faucet until the water re
Download Pdf Manuals
Related Search