Waterboss 700 Instructions / Assembly
Contents
1. 10 11 12 13 14 The appliance may be disinfected with 5 25 sodium hypochlorite which is the active ingredient in household chlorine bleach To disinfect the appliance add 4 0 fluid ounces of chlorine bleach solution to the brine well of the brine cabinet The brine cabinet should have water in it Start a manual regeneration The bypass valve located on the main control valve enables you to bypass the appliance if any work is being performed on the appliance well pump or plumbing See Bypass Valve Use Bypass mode also for watering plants or lawns with untreated water Before putting the appliance back in service after work has been performed turn on the nearest cold water tap until water runs clear Inspect and clean the brine cabinet and air check draw tube assembly annually or when sediment is present in the brine cabinet Potassium permanganate will need to be added periodically to any iron filter Model 950 contains redox media and activated carbon media These have a finite life and will eventually require replacement if the advertised performance capabilities of this device are to be maintained This product is certified for barium and radium 226 228 reduction according to NSF ANSI Standard 44 Any Bypass system must be completely in the Service position to ensure maximum barium and radium 226 228 reduction This product is efficiency rated according to NSF ANSI 44 The stated efficiencies are vali2. Do not use to treat water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the appliance 10 Do not allow your appliance or drain line to freeze oa S NO WaterBoss Softener Owner s Manual 12 2 2010 7 Installation Steps and Start Up Procedures The water softener is capable of treating a combination of undesirable constituents such as iron dirt sediment chlorine and or lead in water See Specifications for the capabilities of your appliance Install set up and use the appliance within the operating limits outlined in this manual Failure to comply with these specifications may decrease the effectiveness of the backwash and cause control valve malfunction The water softener like any other appliance requires correct installation and setting for optimum performance Each water treatment appliance includes water test strips and eight feet of drain line ED Prepare the Placement Area A Make sure the placement area is clean B Turn off the electricity and water supply to the water heater For gas water heaters turn the gas cock to Pilot C Examine the inlet plumbing to ensure that the pipe is not plugged with lime iron or any other substance Clean or replace plugged plumbing Note A minimum 3 4 inch pipe is required between the pressure tank and the appliance for the appliance to function properly D Make sure the inlet outlet and drain connections meet
3. minutes Capacity Water grains gallons grams L 21 702 1 406 28 6 41 00 5 4 108 3 32 46 30 121 15 6 8 36 490 2 364 12 5 4 30 1 113 9 21 702 1 406 Minimum Maximum water and ambient temperature F C 40 120 4 4 48 9 40 120 4 4 48 9 40 120 4 4 48 9 Mineral tank size in cm 10 5 1 8 x 19 26 7 I D x 48 3 10 5 1 9 x 26 26 7 I D x 66 10 5 I D x 26 26 7 I D x 66 Peak flow rate 8 gpm 30 L min 8 2 gpm 31 L min 8 gpm 30 L min Pressure drop at service flow rate of 8 gpm 30 3 L min psi bar 15 1 0 14 6 1 0 15 1 0 Maximum flow rate to drain during regeneration backwash gpm L min 24 9 1 24 9 1 3 0 11 4 Water Pressure min max psi bar 20 120 1 4 8 3 20 120 1 4 8 3 20 120 1 4 8 3 Minimum water flow required gpm L min 24 9 1 24 9 1 3 0 11 4 Maximum chlorine ppm 0 0 0 0 3 0 Controller type 4 Button 4 Button 4 Button Frequency of regeneration Demand Demand Demand Salt storage Ib kg 120 54 4 170 77 1 170 77 1 Height in cm 25 5 64 8 30 5 77 5 30 5 77 5 Footprint in cm 15 x 19 38 x 48 15 x 19 38 x 48 15 x 19 38 x 48 Electrical rating 12 VAC 50 60 Hz 0 015kW hr 12 VAC 50 60 Hz 0 015kW hr 12 VAC 50 60 Hz 0 015kW hr Plum
4. It should be filtered out before Ferric lron the water reaches the softener Organic Iron or Bacterial Attached to other organic compounds in the water Additional treatment is needed to Iron remove this type of iron Colloidal Iron Not dissolved yet stays in suspension A softener cannot remove this type of iron If the water supply contains ferrous iron a commercially available resin bed cleaner should be used every six months Follow the instructions on the container You should also increase your water hardness setting by 5 grains per gallon 86 mg L for every 1 ppm 1 mg L of ferrous iron O Water Characteristics Models 700 900 and 950 require a pH of 7 or above to function properly An iron test to determine iron levels is also necessary The 900 NF Acid Neutralizing Filter adjusts pH levels of 6 3 or above Water Hardness Double check hardness of water with test strips provided to verify that your appliance is right for the job e Model 950 is FOR MUNICIPALLY SUPPLIED WATER without iron Model 950 will condition water up to 35 grains of hardness per gallon 600 mg L e Model 700 will condition water for up to 70 grains of hardness per gallon 1 200 mg L e Model 900 will condition water for up to 90 grains of hardness per gallon 1 540 mg L See Specifications Water Pressure Not less than 20 psi or greater than 120 psi 1 4 8 3 bar constant If water pressure exceeds 70 psi 4 8 bar a pressure regu
5. Model 950 only 93842 WaterBoss Softener Owner s Manual Drain Line 12 2 2010 22 Assembly and Parts Cont Injector Assembly INSERT WITH RIB AT 9 O CLOCK POSITION Figure 15 Injector Assembly Description Quantity Injector Throat Injector Nozzle with Over Mold Gasket O Ring Injector Cap All of the above parts 93223 Injector In conjunction with the Injector Nozzle 53224 it creates the vacuum that draws the brine solution Throat from the brine cabinet The center hole should be clear of debris round and undamaged The Throat should be pressed flush into the opening in the valve If the Throat is removed it must be replaced with a new one 53224 Injector Together with the Throat 93223 creates the vacuum that draws the brine solution from the Brine Nozzle with Cabinet The small hole in the Injector Nozzle 53224 is the one that creates the Over Mold Gasket injection stream that enters the Throat It is important that this hole is round undamaged and clear of debris If this hole becomes clogged do not use anything such as metal objects to Clear this opening Damage may occur Use a clean cloth and flush with water If necessary a wooden toothpick may be used When assembling to the Valve the Nozzle hole should line up with the Throat Flush screen with water to clean The over mold gasket seals between the Injector Nozzle and the Injector Cap 53235 Injector
6. N Plug in the Transformer A Connect the transformer power cord to the back of the controller See Figure 8 B Plug the transformer into an appropriate outlet C Ensure that the outlet selected is not operated by Figure 8 Connect Power Cord an On Off switch Set Up the Controller A Program the appliance controller See Setting the Controller WaterBoss Softener Owner s Manual 12 2 2010 11 Installation Steps and Start Up Procedures Cont Add Water to the Brine Cabinet A Add 2 gallons 7 6 L of water to the brine cabinet After the first regeneration the appliance will automatically refill the correct amount of water into the brine cabinet B Ensure the appliance is in Service position and your water supply is turned on C Press the Regenerate button to advance to the Brine Refill 04 position Let the tank fill with the proper amount of water The controller will then step the valve to the Home position Note This initial startup is the only time you will add water to the brine cabinet Do not add water at any other time ED Fill the Brine Cabinet With Salt A Fill the brine cabinet with salt Use clean white pellet or solar salt Do not mix pellet with solar salt Note Always keep the salt level above the water level For convenience completely fill the tank when refilling with salt B After you add salt including adding it after the tank has run out of salt wait two hours for saturated brine bef
7. cabinet Clean or replace injector Replace throat if removed Remove valve Check for obstruction Not regenerating in proper sequence Magnet disk defective Defective controller Replace magnet disk Replace controller Salty water Plugged injector Low water pressure Drain line or flow control is restricted Brine line restricted or crimped Excessive amount of water in brine cabinet Intermittent pressure drop from feed source Brine valve drips water back to brine cabinet Replace injector screen nozzle and throat Maintain minimum pressure of 20 psi Remove restriction Remove restriction replace if crimped Verify correct water level relative to salt setting Check lines and fittings for loose connections Install check valve on the inlet water line to the appliance Check local plumbing codes first Clean brine valve housing replace piston assembly Controller error messages WaterBoss Softener Owner s Manual E1 Home not found E2 Motor error E3 Home offset E4 Home latched E5 Memory Error 12 2 2010 Cycle power by unplugging the transformer and plugging it back in It will look for Home again Make sure the controller is pushed all the way onto the drive end cap Plug motor in and cycle power If it is already plugged in then motor wiring or the motor plug is defective Disk did not start in proper home location Controller will automatically try to res
8. installation instructions provided with the system The warranty does not cover damage resulting from use with inadequate or defective plumbing inadequate or defective water supply or pressure inadequate or defective house wiring improper voltage electrical service or electrical connections or violation of applicable building plumbing or electrical codes laws ordinances or regulations THIS WARRANTY DOES NOT COVER INCIDENTAL CONSEQUENTIAL OR SECONDARY DAMAGES ANY IMPLIED WARRANTIES ON THE PRODUCT DESCRIBED IN THIS WARRANTY WILL NOT BE EFFECTIVE AFTER THE EXPIRATION OF THIS WARRANTY No dealer agent representative or other person is authorized to extend or expand this limited warranty Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Claims Procedures Any defects covered by this warranty should be promptly reported to WaterBoss 4343 South Hamilton Road Groveport Ohio 43125 When writing about the defects please provide the original owner s name telephone number and original address serial number and model number of the product and date of purchase This information should be listed in General Information at the front of this manual WaterBo
9. ppm mg L of ferrous iron ED Enter Your Setting Number Into the Controller A Press and hold the Set button for about 5 seconds until 25 displays B Press the Change button until the display matches your compensated number Once you pass 70 models 700 and 950 or 90 model 900 the display will reset to 03 C Press Set to save the hardness setting number D To recheck the hardness setting number hold down the Set button for about 5 seconds Note Refer to Specifications for the maximum water hardness that your appliance can handle Your controller is now set WaterBoss Softener Owner s Manual 12 2 2010 16 Advanced Customer Settings Most customers will want to use the factory default settings so no changes are necessary However you can reset the controller settings if the factory default settings are not suitable for your needs Note Be sure to check that the Time of Day is correct Set High Capacity or High Efficiency Your appliance can be programmed for High Capacity HC or High Efficiency HE e High Capacity means the appliance will regenerate less often but use more salt e High Efficiency will make the appliance regenerate more often and use less salt This is the default The High Efficiency setting meets or exceeds the requirement some states have for salt efficiency To Enter Advanced Customer Settings Mode A Press and hold the Set and Change buttons at the same time fo
10. the applicable state and local codes E Check the arrows on the bypass valve to ensure that the water flows in the proper direction See Bypass Valve Caution Do not plumb the appliance in backward F Place the appliance in the desired location using Figure 1 as a guide The diagram in Figure 1 applies to basement slab crawl space and outside installations Hard W Prada Ground Wire and Clamps Copper Pipe Only Well Water Cold Soft 7 C 1 as City Water Meter Outlet Water Heater Drain Line and Overflow Line Figure 1 Appliance Placement WaterBoss Softener Owner s Manual 12 2 2010 8 Installation Steps and Start Up Procedures Cont G For most installations install the appliance after the pressure tank and any water filter appliance or water meter and before the water heater unless otherwise recommended Contact the HelpLine for further assistance in determining the proper installation sequence Water Heaters If less than 10 feet 3 0 of pipe connects the water treatment appliance s to the water heater install a check valve between the water treatment appliance and the water heater as close to the water heater as possible Ensure that the water heater has an adequately rated temperature and pressure safety relief valve H For outside installations the appliance should be enclosed so it is protected from the weather ED Test Your Water A Remove any pa
11. Cap Holds the injector assembly together and seals the assembly to the Main Valve Body WaterBoss Softener Owner s Manual 12 2 2010 23 Assembly and Parts Cont Bypass Assembly Figure 16 Bypass Assembly Description Bypass Assembly also includes items 2 6 Quantity Turbine Sensor Cap Assembly Sensor Cap Screw self tapping Plastic Turbine Axle Turbine Assembly O Ring WaterBoss Softener Owner s Manual 12 2 2010 24 Assembly and Parts Cont Top Fill Plug Assembly 950 O RING Figure 17 Fill Plug Assembly Part Description Quantity 93281 Fill Plug 1 93272 Fill Plug O Ring 1 93281 Fill Plug The Fill Plug 93281 seals the media access ports in the Media Tank Care should be taken that the O Ring seal area is kept clean and free of debris Also the O Ring should be in the proper location in the groove Do not overtighten the Fill Plug when assembling When the flange comes into contact with the Media Tank stop tightening 3 4 inch socket is recommended for assembly WaterBoss Softener Owner s Manual 12 2 2010 25 Assembly and Parts Cont Drive End Cap Assembly Figure 18 Drive End Cap Assembly Description Quantity N 90802 Screw self tapping 90217 Drive Motor 93891 1 4 Hex Nut 93238 Drive Gear 90809 Screw self tapping Cam Cover 93219 Piston Slide Cam Cover 93217 Piston Slide Cam 93583 Drive End Cap 54202 Pisto
12. Gear 93238 is attached at the short end and the Magnet Disk 54502 at the other end The Slide Cam is assembled inside of the Piston Slide 54202 This Cam Shaft should turn freely before the Motor is assembled 93583 Drive End Cap Seals the two openings on the Main Valve Body The larger diameter opening is sealed with an O Ring used as an axial or face seal The O Ring sits in a groove in the End Cap This groove must be free of defects such as pits or scratches and also free of debris The smaller diameter seal is accomplished with an O Ring used as a radial seal The O Ring should be placed on the male boss on the End Cap When assembling the End Cap to the Valve Body care should be taken to make sure the small O Ring is aligned with the opening in the Valve Body and that the large O Ring stays in the groove in the End Cap If misaligned the O Rings can become pinched and leak 54202 Piston Slide The Slide should move freely inside the End Cap Housing 53322 Drive Piston The Drive Piston attaches to the Piston Slide 54202 by placing the slot of the Piston onto the Assembly matching flat of the Slide To remove Piston rotate Piston 90 counterclockwise To replace Piston rotate 90 clockwise until you hear an audible click See reference drawings below Dimple Align Flats Position Piston Assembly 53322 Vertical Slide Piston Assembly Onto Piston Slide Rotate The Piston Assembly 90 Degrees Clockw
13. aged WaterBoss Softener Owner s Manual 12 2 2010 19 Optional Plumbing Procedures Cont Plastic PVC CPVC Pipe Joining Procedures To ensure reliable joint integrity when using solvent cement for PVC CPVC plumbing follow these recommendations A B Cutting The pipe must be cut square to allow for the proper interfacing of the pipe end and the fitting socket bottom Use a wheel cutter miter saw or a ratchet shear for best results Deburring and Beveling Use a knife plastic pipe deburring tool or a file to remove burrs from the end of the pipe Be sure to remove all burrs from the inside as well as the outside of the pipe Remove all loose plastic debris since it could clog the injector All pipe ends should be beveled to permit easier insertion of the pipe into the fitting Failure to bevel the pipe end may cause a wiping effect in the fitting where the cement is forced to the end of the fitting socket This creates a weak joint Test Dry Fit of the Joint Tapered fitting sockets are designed so that an interference fit should occur when the pipe is inserted about one third to two thirds of the way into the socket Occasionally when pipe and fitting dimensions are at the tolerance extremes it will be possible to fully insert dry pipe to the bottom of the fitting socket When this happens a sufficient quantity of cement must be applied to the joint to fill the gap between the pipe and fitting Inspection Cleaning and P
14. al variables Follow the recommended joint curing times on the primer and cement container labels WaterBoss Softener Owner s Manual 12 2 2010 20 Assembly and Parts Cabinet Cover Salt Lid Assemblies Incorrect CEST ANUS US we Description 54306 Salt Port Lid 54324 Valve Cover Assembly 54545 700 Computer Control Assembly 700 and 950 54545 900 Computer Control Assembly 900 54310 Brine Well Cover 93245 12V Transformer Power Cord 54303 Cabinet 700 54309 Cabinet 900 950 54305 Support Panel 93530 Media tank empty 700 only 95505 Media tank empty 900 only 97509 Media tank empty fill plug 950 only WaterBoss Softener Owner s Manual 12 2 2010 21 Assembly and Parts Cont Cabinet and Assemblies C0700A Figure 14 Cabinet and Assemblies Description Overflow Elbow Quantity 04512 Bypass Assembly 93838 O Ring 93281 Fill Plug Model 950 only 93272 O Ring Model 950 only 93808 O Ring 90828 O Ring CO Ni Od On amp Go RO gt 54520 Drive End Cap Assembly 93870 Screw 93504 Injector Assembly 93835 Sleeve 93524 Drain End Cap Barbed Model 700 and 900 only not shown 90614 3 0 Drain End Cap Assembly Model 950 only Ni e e N e el po 93809 Screw V185 Drain Fitting 1 2 MNT x Barb
15. bing connections 1 male MNPT 1 male MNPT 1 male MNPT Shipping weight approximate Ib kg 85 38 6 1 The state of Wisconsin limits iron reduction claims to 5 ppm 2 Use clean white pellet or solar salt 105 47 6 105 47 6 3 In HE mode this is the maximum salt dosage HE mode meets the requirement some states have regarding salt efficiency WaterBoss Softener Owner s Manual 12 2 2010 33 Certificates State of California Department of Health Services Water Treatment Device Certificate Number 05 1718 Date Issued December 12 2005 Trademark Model Designation Replacement Elements Waterboss 700 NA Manufacturer _ Waterboss The water treatment listed on this certificate have met the requirements pursuant to Section 170800 the Hos Saidiy Code Yor Dee PSI latod COL Mania ical Cont Turbidi Radiological C Barium None Radium 226 228 Organic Contaminants None Rated Service Capacity N A Rated Service Flow 8 gpm of Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system State of California Department of Health Services Water Treatment Device Certificate Number 05 1720 Date Issued December 12 2005 Trademark Model Designation Replacement Elements Waterboss 950 NIA Manufacturer _ Waterboss The water Microt j Cont ts and Turbidi None Organic C
16. ckaging or installation materials from the brine cabinet B Test your water quality with the strips provided See Setting the Controller Optionally obtain a report on your water s quality C Turn Off Water Supply A Turn off the water supply B Open the hot and cold water taps to depressurize the lines ED Connect Water Lines Note See Optional Plumbing Procedures for information on copper fittings and joining plastic pipe A Lift and remove the cabinet cover B Install Qest fittings Qest connection fittings are provided with your appliance Qest fittings provide a convenient easy to use three piece assembly for 3 4 inch copper plumbing or 3 4 inch CTS CPVC plastic tubing Ensure that the three components 1 collar 2 metal retaining ring and 3 nylon sleeve are correctly installed in sequence on the pipe See Figure 2 Note Do not use Teflon tape or plumber s putty with Qest fittings They are not necessary Attach the water lines to the appliance in compliance with all state and local building plumbing and electrical codes See Figure 3 Do NOT overtighten the connections on the plastic threads D Check the arrows on the valve to ensure that the water flows in the proper direction Caution Do NOT plumb your appliance in backward Figure 3 Connect Water Lines O WaterBoss Softener Owner s Manual 12 2 2010 9 Installation Steps and Start Up Procedures Cont ED Connect Gravity Overflow Connec
17. ctor assembly Salt bridge has formed due to high humidity or the wrong kind of salt Add salt Remove air check draw tube and flush with clean water Clean injector assembly Clean any sediment from brine cabinet Remove brine piston housing and clear debris from the flow control Straighten thaw or unclog the drain line Remove injector cap and clean nozzle and throat with a wooden toothpick Replace throat if removed Test with a blunt object like a broom handle Push the handle into the salt to dislodge the salt bridge or use hot water around the inside perimeter to loosen salt No soft water The bypass valve is in the Bypass position Appliance is plumbed backward Extended power outage Water hardness has increased Not metering water Place the bypass valve in the Service position Check that appliance is plumbed correctly Reset the time of day Re test the water and re enter a new setting number waterMizer indicator should turn with water usage If no flow see below No flow is indicated when water is flowing The bypass valve is in the Bypass position Appliance is plumbed backward Sensor not receiving signal from magnet on turbine Place the bypass valve in the Service position Check that appliance is plumbed correctly Remove sensor from Bypass housing Test with magnet on either flat side of sensor If flow is indicated check turbine If no flow replace sensor Flow indicated when water is not bein
18. d only at the specified salt dosage and 8 gpm 30 L m Rated Efficiency 5 066 grains lb 722 grams kg Salt Dosage Capacity at That Dosage 110 0 45 kg 5 066 grains 328 grams 5 510 grains lb 785 grams kg 110 0 45 kg 5 510 grains 357 grams 5 066 grains lb 722 grams kg WaterBoss Softener Owner s Manual 110 0 45 kg 5 066 grains 328 grams 12 2 2010 5 Checklist Before Installation Refer to this checklist before installation O Water Quality lf the water supply contains sand sulfur bacteria iron bacteria tannins algae oil acid or other unusual substances consider pre treating the water to remove these contaminants before the water supply enters the appliance unless the appliance is represented as being capable of treating these contaminants in its specifications The appropriate WaterBoss Water Filter can address these water shortcomings Model 900 IF Iron Filter Reduces iron manganese hydrogen sulfide and iron bacteria Model 900 NF Acid Neutralizing filter Adjusts low pH water to a non corrosive state lron A common problem found in many water supplies is iron It is important to know what type of and how much iron is in the water supply Iron Type Description Ferrous lron sometimes called clear Only type of iron that can be treated with a water softener water or dissolved iron Insoluble and the particles can eventually foul a resin bed
19. eature on for a minimum of two weeks The frequent regeneration will eliminate iron buildup in the resin bed The use of salt with an iron cleaning agent or iron out cleaner is recommended for continuous use as a preventive measure against iron fouling of the resin bed Use this feature every six months as a part of your routine maintenance procedure to ensure a long service life for your water treatment appliance Regenerate Used when starting your water conditioner to start an immediate regeneration or to restore capacity if you run out of salt To Start an Immediate Regeneration 1 Press and hold the Regenerate button for about five seconds 2 The appliance is in regeneration mode and will display the status of each cycle 3 After all regeneration cycles are complete the display will return to normal operating mode To Quickly Advance Through the Regeneration Cycles used when starting up or diagnosing the appliance only 1 Press and hold the Regenerate button for about five seconds until the cycle begins 2 The cycle position will display for example 01 3 If the controller does not advance to the next cycle position after 20 seconds press and hold the Regenerate button until the cycle number changes about 2 seconds Each cycle can be advanced by pressing the Regenerate button Always wait until the cycle position displays before advancing to the next cycle position WaterBoss Softener Owner s Manual 12 2 2010 15 Setti
20. eds or thousands depending on how much capacity is remaining For example 88 8 800 gallons 33 3 300 or 33 000 liters Recharge Regeneration Status Shows regeneration cycle numbers during regeneration The read out will flash with the cycle number The flashing regeneration numbers are First cycle 01 Second and Third cycles 02 Brine Slow Rinse First Backwash Fourth cycle 03 Second Backwash Fifth cycle 04 Brine Refill Sixth cycle HO Service Briefly When regeneration is complete the display shows the number of gallons in hundreds of soft water remaining See above Regeneration typically is complete in about 30 minutes waterMizer Indicates that water is flowing through the appliance the waterMizer indicator turns whenever water is being used useful for checking for proper plumbing and leaks powerClean Displays when feature is activated See Power Clean Button WaterBoss Softener Owner s Manual 12 2 2010 14 Four Button Controller Cont Set Function Used to set Customer Settings Change Used to change Customer Settings Power Clean 700 and 900 only Activates deactivates the powerClean feature which is a service maintenance step for water supplies that have an excessive amount of iron powerClean will display when this feature is activated The appliance will regenerate every other day with five pounds 2 3 kg of salt Leave the powerClean f
21. equipment serial number and date of original installation to WaterBoss PREPAID and replacement parts will be returned by WaterBoss to the original owner FREIGHT COLLECT Further Exclusions and Limitations on Warranty THERE ARE NO WARRANTIES OTHER THAN THOSE DESCRIBED IN THIS WARRANTY INSTRUMENT This warranty does not cover any service call or labor costs incurred with respect to the removal and replacement of any defective part or parts WaterBoss will not be liable for nor will it pay service call or labor charges incurred or expended with respect to this warranty In the event the water supply being processed through this product contains sand bacterial iron algae sulphur tannins organic matter or other unusual substances then unless the system is represented as being capable of handling these substances in the system specifications other special treatment of the water supply must be used to remove these substances before they enter this product Otherwise WaterBoss shall have no obligations under this warranty WaterBoss Softener Owner s Manual This warranty does not cover damage to a part or parts of the system from causes such as fire accidents freezing or unreasonable use abuse or neglect by the owner This warranty does not cover damage to a part or parts of the system resulting from improper installation All plumbing and electrical connections should be made in accordance with all local codes and the
22. er s Manual 12 2 2010 4 Getting Maximum Efficiency From the Appliance To achieve the maximum benefit and performance from this appliance familiarize yourself with this manual and the appliance 1 The salt level should always be at least 1 3 full Refill the salt when the level drops below the water level in the brine cabinet A resin cleaner can be used on a monthly basis A clean pellet solar or cube type salt is recommended Do not use rock salt Caution Do not mix different types of salt 2 You may switch to a salt substitute such as potassium chloride in place of water conditioner salt at any time If potassium chloride is used in place of salt increase your hardness setting by 12 multiply by 1 12 See Setting the Controller Caution Do not use potassium chloride if your water contains iron and or manganese 3 Should your electricity be off for any reason check your controller for the correct time and reset as necessary See Advanced Customer Settings 4 Program the appliance to regenerate at a time when the water is not being used If there is more than one appliance allow two hours between each regeneration 5 Protect the appliance including the drain line from freezing 6 Adhere to all operational maintenance and placement requirements 7 If dirt sand or large particles are present in the water supply the appropriate WaterBoss filter can eliminate this problem Efficiency Statements 8
23. et itself by finding Home and continuing the regeneration Make sure the controller is pushed all the way onto the drive end cap Gear teeth are not engaged gear is stripped or something is jammed in the valve Cycle the power to reset Replace controller 32 WaterBoss Water Conditioner Specifications Max Compensated Hardness gpg mg L 70 1 200 90 1 540 35 600 Maximum ferrous iron reduction 10 ppm 10 ppm 0 Minimum pH standard units 7 7 7 Media type and amounts Self Cleaning Filter Media Super Fine Mesh Resin Total 0 7 cu ft 20 L Self Cleaning Filter Media Super Fine Mesh Resin Total 1 cu ft 28 L Redox Media 4 Ib 1 8 kg Activated Carbon 0 25 cu ft 7 L Super Fine Mesh Resin 0 7 cu ft 20 L Total 1 cu ft 29 L Time minutes Water gallons L Capacity grains grams 11 1 42 0 1 5066 15 00 0 5 328 11 1 42 0 1 5510 15 00 0 5 357 1 5066 12 3 16 00 0 5 328 46 6 Time minutes Water gallons L Capacity grains grams 13 9 19 30 52 6 2 0 0 9 8 140 527 139 21 00 56 0 5 5 22 251 2 5 1 441 2 0 15 1 19 30 0 9 8 140 527 Time minutes Water gallons L Capacity grains grams 224 32 00 85 8 6 5 2 9 18 109 1 173 23 5 33 30 89 0 8 5 29842 3 9 1 933 65 2 9 18 109 1 173 Time
24. g used The household plumbing system has a leak Repair the leak No read out in display WaterBoss Softener Owner s Manual Electric cord is unplugged No electric power at outlet Defective transformer Defective circuit board High ambient room temperature If the temperature exceeds 120 F 48 9 C the display will blank out This does not affect the operation of the controller 12 2 2010 Plug in the transformer Check power source Make sure outlet is not controlled by a switch Test with volt meter for 12 VAC at control If less than 10 VAC or greater than 14 VAC replace the transformer With 12 VAC present at controller replace the controller No action necessary 31 Troubleshooting Cont Problem Appliance stays in regeneration Possible Cause Controller not attached properly Defective magnet disk Foreign object in valve body Broken valve assembly Motor running Solution Make sure the controller is pushed all the way onto the drive end cap Replace magnet disk Remove foreign object s from the valve body Repair the drive end cap Excess water in brine cabinet Restricted frozen or pinched drain line Plugged brine line brine line flow control or air check draw tube Plugged injector assembly Sticking brine refill valve Remove restriction thaw or straighten drain line Clean flow control air check draw tube and brine line Clean any sediment from the brine
25. iance before the water heater 4 Install the appliance after the pressure tank on well water installations 5 Examine the inlet line from the pressure tank to appliance on well water with iron recommended minimum inlet pipe size 3 4 inch On municipal water recommended minimum inlet pipe size is 1 2 inch I D Install a pressure reducing valve if the inlet pressure exceeds 70 psi 4 8 bar Install a gravity drain on the cabinet 8 Secure the drain line on the appliance and at the drain outlet See nstallation Steps and Start Up o Procedures 9 Allow a minimum of 8 to 10 feet 2 4 to 3 0 m of 3 4 inch pipe from the outlet of the appliance to the inlet of the water heater Do Not 1 Do not install if checklist items are not satisfactory See Checklist Before Installation 2 Do not install if the incoming or outlet piping water temperature exceeds 120 F 48 9 C See Specifications 3 Do not allow soldering torch heat to be transferred to valve components or plastic parts when using the optional copper adapters 4 Do not overtighten the plastic fittings Do not plumb the appliance against a wall that would prohibit access to plumbing See nstallation Steps and Start Up Procedures Do not install the appliance backward Follow the arrows on the inlet and outlet Do not plug the transformer into an outlet that is activated by an On Off switch Do not connect the drain and the overflow gravity drain lines together
26. ise Until You Hear An Audible Click As It Snaps Into Place WaterBoss Softener Owner s Manual 12 2 2010 27 Assembly and Parts Cont Brine Valve Housing Assembly Static O Ring Concave side Figure 19 Brine Valve Housing Assembly Description Quantity Piston Assembly includes O Ring amp Spring O Ring Housing 0 5 gpm Flow Control O Ring Brine Valve Cap Screw self tapping Brine Valve Elbow O Ring 54521 Entire Assembly all of the above parts CO CO NI gt AJA Go Ro gt 53511 Brine The Piston should have an O Ring on the shaft side of the flange and a spring pressed onto a boss on Piston the other side The O Ring should be free of defects such as cuts or debris on the shaft side 53510 Housing Just inside the entrance hole for the Brine Piston 53511 is a concave seat area that must be free of defects such as nicks indentations or debris This seat area ensures a leak free seal for the static O Ring on the Brine Piston If any defects are detected by visual inspection repair or replace as needed 90843 0 5 gpm The Flow Button has two distinct and different sides One is flat the other is concave The button Flow Control should be centered in the housing opening with the four locator ribs with the concave side facing the Housing End Cap 93247 WaterBoss Softener Owner s Manual 12 2 2010 28 Assembly and Parts Cont Safety Shutoff As
27. lator is recommended O Water Supply Flow Rate A minimum of 2 4 gallons 9 1 L for the 700 and 900 models to 3 gallons 11 4 L for the 950 model per minute or equal to the backwash flow rate of the particular model is recommended For the purposes of plumbing sizing only the rated service flow rate and corresponding pressure loss may be used Prolonged operation of a water conditioner at flow rates exceeding the tested service flow rate may compromise performance WaterBoss Softener Owner s Manual 12 2 2010 6 Checklist Before Installation Cont Water Temperature Not less than 40 or greater than 120 F 4 4 48 9 C Drain Drain the appliance to an appropriate drain such as a floor drain or washer drain that will comply with all local and state plumbing codes To prevent back siphoning provide an adequate air gap or a siphon break See Installation Steps and Start Up Procedures J Electricity The transformer supplied is for a standard 115 volt 60 cycle AC outlet for locations in North America or 220 volt 50 cycle AC outlet for locations outside North America If you have any questions call the HelpLine See General Information at the front of the manual for information about the HelpLine Precautions Do 1 Comply with all state and local building plumbing and electrical codes 2 Test your water quality with the strips provided Optionally obtain a report on your water s quality 3 Install the appl
28. lear water Use this guide to attain the maximum benefit from your appliance Keep it handy for a reference guide and service log If you have trouble with the operation of your appliance see Troubleshooting in the back of this manual or contact the HelpLine 1 800 437 8993 from 8 a m to 5 p m EST The HelpLine fax number is 614 836 9876 Help is also available on the WaterBoss website www waterboss com The HelpLine is available to answer questions about specific water problems appliance installation and operation When calling the HelpLine please have this guide and the serial number of your appliance available WaterBoss 4343 S Hamilton Rd Groveport OH 43125 Warning This appliance must be applied to potable water only Note The manufacturer reserves the right to make specification and product changes without prior notice This manual is for installation operation and maintenance of the following water conditioning appliance models e WaterBoss 700 e WaterBoss 900 e WaterBoss 950 For Owner s Reference Date of Installation Model Number Serial Number Hardness Iron pH Water Pressure Water Temp Returned Warranty Card Date 1 The serial number is located underneath the valve cover 2 Completely fill out the Warranty Card and return it by mail to ensure that the appliance is registered with the factory and the warranty becomes validated WaterBoss Softener Own
29. n Slide 90818 Screw self tapping 54521 Brine Valve Assembly 90821 O Ring 54502 KIT Magnet Disk Assembly 90828 O Ring 93808 O Ring 53322 Drive Piston Assembly 93839 Drain Gasket 54520 Entire Assembly all of the above parts except 1 2 and 13 CO Ni OO On amp Go Ro gt N ma Sa NI Bo WaterBoss Softener Owner s Manual 12 2 2010 Assembly and Parts Cont Drive End Cap Assembly Cont 90217 Drive Motor The Motor is held in place by two 1 2 inch self tapping screws The screws should be snug The brass pinion gear on the Motor should engage the plastic Drive Gear 93238 The wires should be securely fastened to the Controller 93238 Drive Gear The Drive gear is assembled to the Slide Cam by means of a keyed opening which transfers the torque generated by the Motor to the rest of the drive system If the drive system becomes jammed this opening can become rounded causing the gear to turn but not the Piston Slide Cam If this occurs clear the jam and replace the Drive Gear 93238 and Piston Slide Cam 93217 93219 Piston Slide The cover secures the Piston Slide Cam 93217 in place and acts as a bushing for the Cam Cam Cover Shaft 93217 Piston Slide This is the heart of the drive system There is a threaded stainless steel shaft that runs through Cam the main drive axle The Drive
30. ng the Controller Determine the Controller Setting Number For municipal water call the water department to determine the hardness and pH of your water supply B For well water use the hardness test strips provided with your appliance or have a sample of your untreated water tested by a water testing laboratory 1 Test Strips Follow the instructions on the test strips If the color on your test strip is between two readings use the higher number Compare the colors as soon as you remove them from your water This number gives the hardness in grains per gallon and parts per million mg L 2 Testing Laboratory To ensure proper settings Figure 11 Hardness Test Strips have a sample of your untreated water tested for iron and pH To find a facility to test your water sample check your Yellow Pages under Water Analysis or Water Testing or contact the company below to conduct a test for you WATERSCREEN National Testing Laboratories Inc 1 800 458 3330 from 9 a m to 5 p m EST 3 If the pH is below seven and you have a 700 or 900 unit call the HelpLine listed in General Information C Use the following example to determine the controller setting Your Water Example Metric Example Enter hardness grains per gallon mg L 342 If your water contains 3 ppm mg L iron add 15 257 257 The sum is your controller setting number 600 rounded Increase your water hardness setting by 5 grains per gallon for every 1
31. ontain None Rated Service Capacity N A Rated Service Flow 8 gpm litions of 3 Do not use with water that is microbiologically unsafe of unknown quality without adequate disinfection before or after the system WaterBoss Softener Owner s Manual State of California Department of Health Services Water Treatment Device Certificate Number 05 1719 Date Isswed December 12 2005 Tragemark Model Designation Replacement Elements Waterboss 900 NIA Waterboss Prosenes 51 5 NIA Manufacturer _ Waterboss The water treatment device s listed on this certificate have met the Code conta requirements pursuant to Section 116830 of the Health and for the folowing health related contaminants a Microbiological Contaminants and Turbidity Inorganic Radiological Contaminants None Barium Radiure 226 228 Organic Contaminants None Rated Service Capacity N A Rated Service Flow 8 gpm Do not use with water that is microbiologically le or of wi quality without adequate disinfection before or after the system 12 2 2010 34 Notes WaterBoss has these third party listings Made In The USA WaterBoss water softener In Business Since 1956 www waterboss com 4343 South Hamilton Road Groveport OH 43125 LITHO USA 2010 F93966 RV1210HQWI
32. option Off B When the desired setting is displayed press Set WaterBoss Softener Owner s Manual 12 2 2010 17 Advanced Customer Settings Cont 0 9 0 Set Gallons or Liters Display reads Gallons or Liters x 100 To Set Gallons or Liters A Press Change to toggle between gallons and liters Choosing Gallons sets the controller to English units and choosing Liters sets it to metric units B When the desired units are displayed press Set Set Time Format Display reads 12 if gallons were chosen or 24 if liters were chosen To Set Time Format A Press Change to toggle between 24 and 12 This controls the selection of a 12 hour AM PM or 24 hour clock If 24 hour 00 midnight B When the desired time format is displayed press Set Set Time of Day Display reads Set Time and 12 or 24 To Change Time of Day A Press Change until the current time is displayed Default is 12 PM Note Set time to the nearest hour B When the desired time is displayed press Set Set Regeneration Time Display reads Set Reg Time followed by the current regeneration time that is set 02 To Change Regeneration Time A Press Change Default is 2 AM B When the desired regeneration time is displayed press Set Note Whenever you experience an electrical outage check your controller for the correct time Make any necessary corrections Programming is now complete Wate
33. ore starting any regeneration Caution Use of potassium chloride when iron and or manganese are present in the raw water supply is not recommended ED Complete the Installation Ensure that the appliance is in the Service position See Figure 7 B Ensure the water supply is on C Turn on the electricity and water supply to the water heater For gas water heaters return the gas cock to On D Open a cold water tap and allow the appliance to flush for 20 minutes or until approximately 72 gallons have passed through the appliance This procedure is required to meet NSF requirements Verify the flow rate on the controller which indicates water flow See Figure 10 E Replace the cabinet cover WaterBoss Softener Owner s Manual 12 2 2010 12 Bypass Valve Your appliance is equipped with a bypass valve The bypass valve can isolate the appliance should the appliance malfunction or leak It can also permit the use of untreated water for watering plants shrubs or lawns The bypass is located on the main control valve See Figure 9 To engage the bypass turn the knob to the Bypass position The appliance will be bypassed and all water to the home is raw untreated water To prevent untreated water from entering the home water should not be used inside the home when the appliance is in Bypass mode Ensure that the appliance is returned to Service mode when the appliance is repaired or the use of untreated water is complete by
34. r 3 seconds The display should show only the controller type After 3 seconds the entire screen is lit for a half second and then HC displays Press Change to toggle the digit display between HC and HE C When the desired value is displayed press Set Note HE ensures the appliance chooses salt settings that get 4 000 grains per pound 570 grams kg of salt for each regeneration or better This choice meets or exceeds the requirement some states currently have in regards to salt efficiency pa Note All models are equipped with patented capacity guard Once in HC or HE you can set the mode hours to next regeneration gallons or liters time format time of day and time of regeneration ED Set Mode Display reads Demand Mode To Change Mode A Press Change Delay Mode allows regeneration at a specific time for example at 2 a m when less water is typically being used Demand Mode triggers a regeneration as soon as softening capacity is exhausted This is the default B When the desired mode is displayed press Set ED Set 96 Hours Until Regeneration Display reads 96 Hours To Change Setting A Press Change to turn Off If 96 Hours is selected the appliance will work no more than 4 days without a regeneration Default is for 96 Hours to be On Note If there is iron in your water select this option If you are using model 950 on most municipal water supplies turn this
35. rBoss Softener Owner s Manual 12 2 2010 18 Optional Plumbing Procedures This section provides information on plumbing with copper fittings and with plastic pipe Hard Plumbing the Bypass With Copper Fittings Do not use Qest fittings for hard plumbing with copper fittings When preparing the male threaded fittings of the adapter use the following guidelines to avoid damage to the plastic pipe threads A B Wrap the threads three times with 1 2 in wide Teflon tape Place each consecutive wrap on top of the previous wrap To prevent tearing of the tape use Teflon paste on the first two male threads only The paste lubricates the tape and fills the small void areas that might exist between the threads When the joint is complete there will be a small bead of sealant at the fitting interface which indicates a properly joined connection Use a union with a threaded connection to facilitate repair of potential leaks in soldered joints Prepare the copper tail assemblies in advance to enable them to cool prior to final assembly Advance preparation and cooling will prevent heat damage to the plastic pipe threads of the adapter Ensure that the copper tube is at least 4 in 10 cm long Turn the fitting counterclockwise until you feel the threads engage and then tighten to prevent cross threading Do NOT overtighten the fittings Caution Do NOT allow heat from the torch to transfer to the plastic valve component which could be dam
36. riming Inspect the inside of the pipe and fitting sockets and remove dirt grease or moisture with a clean dry cloth If wiping fails to clean the surfaces use a chemical cleaner Check for possible damage such as splits or cracks and replace if necessary Use purple primer to penetrate and soften the bonding surfaces of the PVC or CPVC pipe and fittings Proceed without hesitation to the cementing procedure while the primed surfaces are still wet Application of Solvent Cement Apply the solvent cement evenly and quickly around the outside of the pipe while the primer is still wet Apply a light coat of cement evenly around the inside of the fitting socket Do not allow excess cement to puddle in the fitting Apply a second coat of cement to the pipe end Joint Assembly Working quickly insert the pipe into the fitting socket and give a one quarter turn of the pipe or fitting while pushing toward the fitting stop This action will evenly distribute the cement Do NOT continue to rotate the pipe or fitting after the stop has been reached Hold the joint tightly together for about 15 seconds to prevent the pipe from creeping out of the fitting A good joint will have sufficient cement to make a small bead all the way around the outside of the fitting hub The joint should not be disturbed immediately after the cementing procedure Allow adequate time for the joint to cure properly Exact drying time is hard to predict because of environment
37. s 25 feet 7 6 m or longer increase the drain line to 3 4 inch I D The end of the drain line must be equal to or lower in height than the control valve Caution The drain line must not be kinked crimped or restricted in any way WaterBoss Softener Owner s Manual 12 2 2010 Figure 4 Gravity Overflow Connection Figure 5 Connect Drain Line Installation Steps and Start Up Procedures Cont 7 J Flush Lines A Place the appliance in the Bypass position See Figure 6 B Turn on the main water supply C Open the nearest cold water faucet to flush the plumbing of any excess soldering flux air or any other foreign material D Return the appliance to Service mode Note To prevent untreated water from entering your home remember to not use water inside your home when the appliance is in Bypass mode Remember to return the appliance to Service mode when you have finished using untreated water Check for Leaks A Close all faucets B Check all lines and connections for leaks If leaks are found 1 Turn off the main water supply 2 Open a cold water faucet to depressurize the lines 3 Close the faucet to eliminate any siphoning action 4 Repair all leaks Turn on the water supply 6 Place the appliance in the Service position to slowly fill the media tank See Figure 7 Open a cold water faucet to purge air out of the media tank 8 Close the faucet and recheck for leaks
38. sembly Figure 20 Safety Shutoff Assembly Description Quantity Safety Shutoff See Figure 21 Float Air Check 700 Air Check 900 950 54526 Entire Assembly all of the above parts for 700 54330 Entire Assembly all of the above parts for 900 and 950 WaterBoss Softener Owner s Manual 12 2 2010 29 Assembly and Parts Cont Safety Shutoff Valve Elbow Installation 3 8 Plastic Gripper 3 8 Retainer Sleeve 3 8 Plastic Tube Wrist Pin 1 2 Retainer Sleeve 1 2 Plastic Gripper 1 2 Nut lt Air Check Draw Tube Figure 21 Safety Shutoff Valve Elbow Installation Description Quantity 1 54112 1 2 Compression Assembly 54138 3 8 Compression Assembl 1 The nut gripper and retainer sleeve are a three piece assembly that can come apart if removed from the elbow body Parts must be reassembled exactly as shown to function properly When connecting the 54315 brine valve elbow 3 8 inch plastic tube first assemble the nut gripper and retainer sleeve on the tubing Then screw the nut on the elbow body With a wrench tighten the nut securely to create a water tight connection WaterBoss Softener Owner s Manual 12 2 2010 30 Troubleshooting No soft water after regeneration No salt in brine cabinet Sediment in brine cabinet has plugged the brine line and air check draw tube Flow control is plugged Drain line is pinched frozen or restricted Clogged inje
39. ss reserves the right to replace defective parts with exact duplicates or their equivalent Call the HelpLine 1 800 437 8993 for Return Information from 8 a m to 5 p m EST The HelpLine fax number is 614 836 9876 12 2 2010 2 Contents General Information 4 Getting Maximum Efficiency From the Appliance ni 5 Efficiency Statements 5 Checklist Before Installation sorisa a dne 6 Precautions searre 7 Installation Steps and Start Up Procedures csscscssscssssssssssssssssssesesessseseeseeeesseessssssssseasasasasaetererereeess 8 Bypass Valo cers 272 M 00 1 0020 E00 eae ey ee eae 13 Four Buttoni Controller ere 14 S tting the OTM NS pease egos 16 Advanced Customer SCTE Sc 17 Optional Plumbing PROGR OUNCE ES ead nese eee 19 and a 2 Troubleshooting 31 WaterBoss Water Conditioner Specifications 33 ST Sea c oe 5 94 WaterBoss Softener Owner s Manual 12 2 2010 3 General Information Congratulations on choosing a superior WaterBoss water treatment appliance Soon you and your family will be enjoying clean c
40. t rBoss A water softener Wai MODELS 700 900 AND 950 OWNER S MANUAL AND INSTALLATION GUIDE VERSION 7 3 10 Year Limited Warranty Whom Warranty Is Extended This warranty is issued to the original owner at the original location site and is not transferable to other sites or to subsequent owners of the system TO PLACE THE EQUIPMENT UNDER WARRANTY THE WARRANTY REGISTRATION CARD MUST BE COMPLETED AND RETURNED BY THE ORIGINAL OWNER TO WaterBoss WITHIN 30 DAYS OF INSTALLATION Coverage This limited warranty covers the WaterBoss system delivered to the original owner at the original location when the system is purchased for personal family or household use It is intended to cover defects occurring in workmanship or materials or both Warrantor s Performance and Length of Limited Warranty WaterBoss warrants that upon receipt from the original owner of any mechanical or electronic part which is found to be defective in materials or workmanship WaterBoss will repair or replace the defective item for 3 years from date of original installation Media is not warranted WaterBoss further warrants that upon receipt from the original owner of any WaterBoss media tank valve body brine cabinet found to be defective in material or workmanship WaterBoss will repair or replace the defective item for 10 years from date of original installation All defective parts must be returned along with the
41. tion The overflow line drains away excess water should the tank fill with too much water or the appliance malfunction A Attach the overflow elbow and check that it is in the down position See Figure 4 B Connect 1 2 inch 12 7 mm tubing size cannot be reduced between the overflow fitting and a suitable floor drain laundry tub or other suitable waste receptor This tubing is not supplied with the appliance Ensure that the overflow line ends at a drain that is at least 3 inch 76 mm lower than the bottom of the overflow fitting Maintain a minimum of 2 inch 50 mm air gap The gravity line cannot be run overhead ED Connect Drain Line The drain line carries away the backwash water as part of the regeneration cycle A Connect the drain line to the drain end cap See Figure 5 with a minimum 1 2 inch 12 7 mm D tubing supplied The size cannot be reduced Note On the 950 model screw the barbed drain fitting into the drain end cap B Route the drain line to a floor drain laundry tub or other suitable waste receptor Maintain a minimum 2 inch 50 mm air gap between the drain line and the flood level rim of the waste receptor to prevent back siphoning This drain line should make the shortest run to the suitable drain C The drain line may be elevated up to 8 feet 2 4 m from the discharge on the appliance as long as the water pressure in your system is 40 psi 2 8 bar or more D If the drain line i
42. turning the knob to Service To blend hardness back into the water using the bypass turn the knob slightly from the Service position toward the Bypass position Figure 9 Bypass Valve WaterBoss Softener Owner s Manual 12 2 2010 13 Four Button Controller This appliance features a four button controller with an LCD display The controller can be used to view the appliance s status perform regenerations and change settings The controller must be set up correctly for the appliance to perform properly Note Ensure that the bottom of the controller is firmly locked onto the four tabs on the top of the drive end cap assembly See Cabinet and Cover Assemblies diagram later in this manual Controller Part LCD Display Figure 10 Four Button Controller Function Shows the status of the controller Demand Mode The controller measures water usage and regenerates based on need so you do not have to worry about vacation settings or extra guests The appliance will regenerate using only the necessary amount of water and salt If your power has been off the appliance will retain programmed settings indefinitely Note You should not need to change from Demand Mode Soft Water Remaining Shows the gallons or liters of soft water remaining until the next automatic regeneration Typically each person in the household uses about 75 gallons 284 L per day Water remaining is in gallons in hundreds or liters in hundr
Download Pdf Manuals
Related Search