IRON-A-WAY NE421AU Installation Guide
Contents
1. mime Cemters Buulkt lim Installation Instructions Models A 46 A 42 E 342 NE 342 NE 242 Recessed Mounting Instructions Surface Mounting Instructions Electrical Instructions Tools Needed Stud Finder Optional Carpenter s Level Tape Measure Utility Knife Phillips Screwdriver Small Flat Head Screwdriver 1 4 Nut Driver Optional Drill Electric Recommended 1 8 Drill Bit 1 4 Drill Bit Surface Mount Safety Glasses Rough In Kit available for use prior to drywall being installed Great for new construction or open wall reconstruction when remodeling Rough In Kit simplifies installation at a later date when room completed and wall coverings and trim have been applied Recessed Mounting NE 242 Models Not Available for Recessed Mounting 1 Determine desired ironing board height using the chart below Care should be taken to ensure the unit will be mounted at the desired ironing board height A 42 E 342 with Optional Swivel E 342 A 46 A 46 with Optional Swivel NE 342 with Optional Swivel NE 342 Board Height Board Height Board Height Board Height Above Floor Position Position Position Position Position Position Position 3 30 7 29 36 28 35 27 34 26 33 25 24 23 22 21 20 19 Using a stud finder locate the wall studs to be used for mounting Locate the existing wiring or other utilities in the wall to prevent drilling into or severing a wire or other utility during i2. ion 36 3 16 Standing Area Clearance 24 The recommended distance from the side of the ironing board where the user will typically stand to ensure adequate space for ironing Using a 3 16 drill bit pre drill a pilot hole into the wall stud where the cabinet will be attached to the wall taking care that the installation height is as desired Determine the proper mounting screw location inside cabinet so mounting position is located on wall stud as intended Location for mounting screw should be as close to the center of the cabinet as possible Using a 1 4 drill bit pre drill hole in the upper and lower cross braces located inside the cabinet as determined in the previous step taking care that the holes in both braces are drilled to same measurement Partially start mounting 14 x 3 1 2 screw into upper cross brace for installation of ironing center If installing an electrical model please review Electrical Instructions now If installing a non electrical model do not install your own electrical outlet inside cabinet Warranty voided if independent electrical outlet installed within non electrical ironing center cabinet Begin installation by carefully lifting the ironing center into position Attach cabinet to wall by fully inserting the screw in the upper cross brace into the pre drilled hole in the wall stud Plumb and level the cabinet Shim if necessary Tighten cabinet to wall by fully turning installation scre
3. nstallatio Determine the desired location has adequate clearance for ironing Door opens approximately 180 Allow at least 16 from side of cabine for door to swing open A 46 with Optional E 342 with Optional Swivel Swivel NE 342 with Optional Swivel Distance from Wall to Tip of Ironing Board 50 1 4 46 7 8 Swivel Clearance from Cutout Opening of Cabinet 16 7 8 14 5 8 A 42 Distance from Wall in Full Swivel Position 32 1 4 32 5 8 Standing Area Clearance 24 24 The recommended distance from the side of the ironing board where the user will typically stand to ensure adequate space for ironin Cut an opening in the wall per the opening sizes shown below Opening Size 14 1 4 x 59 7 8 x 3 7 8 14 1 4 x 47 1 8 x 3 7 8 14 1 4 x 47 1 8 x 3 7 8 14 1 4 x 47 1 8 x 3 7 8 Attach 2 x 4 cross support cleat between the studs level with the bottom of the opening The cabinet will be attached to studs using four screws one in each side at the top of cabinet and one in each side at bottom cabinet Using a 1 8 drill bit pre drill pilot holes approximately 14 from the top of the cabinet and 1 1 2 from the back of the cabinet Fc models without a swivel pre drill pilot hole approximately 14 from the bottom and 1 1 2 from the back of the cabinet For models with swivel board complete Steps 8 9 and 10 before pre drilling pilot holes for bottom locatior Note If an electrical model is being i
4. nstalled the temporary removal of the electrical wireway may be helpful to complete this step Reinstall electrical wireway after cabinet is attached to studs If installing an electrical model please review Electrical Instructions now If installing a non electrical modeldo not install your own electrical outlet inside cabinet Warranty voided if independent electrical outlet installed within non electrical ironing center cabinet Begin installation by carefully lifting ironing center into the wall opening Plumb and level the cabinet Shim to fit For models with swivels continue with Step 12 For models without swivels attach cabinet to studs using the four pre drilled holes with four 10 x 1 1 2 screws Once complete continue to Step 13 Attach cabinet to studs using the two pre drilled holes and two 10 x 1 1 2 screws for the top installation Locate the side ironing boar brackets that are secured to the cabinet with three screws each Remove the top screw only from each side bracket Use this locatior to pre drill pilot holes for bottom installation location Pre drill a pilot hole through top hole in each bracket into stud Finish attaching cabinet into studs using the 14 x 2 1 2 screws for the just completed two pre drilled holes in each side bracke Decorative trim may be added to cover any irregular cuts when making opening for ironing cente Surface Mounting 10 11 12 13 14 When surface mounting reces
5. ou are placing the ironing center into its location feed the free supply wire through the romex connector attached to the electrical wireway 5 After mounting of ironing center connect all power supply wires and ground wires in accordance with all electrical codes 6 Reinstall the two screws into the electrical wireway cover Make sure no wires are pinched when reinstalling the cover IRON A WAY Inc 220 West Jackson Morton IL 61550 1551 USA a Bus 309 266 7232 Fax 309 266 5088 _o 2 www ironaway com 001095 04 09
6. sed units it is recommended a trim kit be installed Determine desired ironing board height using the chart below Care should be taken to ensure the unit will be mounted at the desired ironing board height A 42 A 46 E 342 with Optional Swivel with NE 342 with Optional Swivel E 342 A 46 Optional Swivel NE 242 with Optional Swivel NE 342 NE 242 Board Height Board Height Board Height Board Height Board Height Above Floor Position Position Position Position Position Position Position Position 30 37 35 29 36 34 28 35 33 27 34 32 26 33 31 25 24 23 22 21 20 19 Note NE 242 with Swivel Option does not adjust in vertical height Using a stud finder locate the wall stud to be used for mounting Stud should be located as close to the center of cabinet as possible Locate the existing wiring or other utilities in the wall to prevent drilling into or severing a wire or other utility during installation Determine the desired location has adequate clearance for ironing Door opens approximately 180 Allow at least 16 from side of cabinet for door to swing open A 42 A 46 with E 342 E 342 with Optional Swivel NE 242 with Optional NE 342 NE 342 with Optional Swivel Optional Swivel NE 242 Swivel 51 47 14 5 8 14 5 8 36 13 16 32 5 8 24 24 Distance from Wall to Tip of Ironing Board 54 1 4 Swivel Clearance from Side of Cabinet 16 7 8 Distance from Wall in Full Swivel Posit
7. w Insert second 14 x 3 1 2 screw into pre drilled hole in bottom brace of cabinet and attach to wall making sure cabinet remains level and square Decorative trim may be added to cover any irregularity on wall Recommendation On all adjustable swivel models locate side ironing board brackets that are secured to the cabinet with three screws each Remove the top screw only from each side bracket Use this location to pre drill pilot holes into trim Insert into the two pre drilled holes in each side bracket 14 x 1 screws not included ELECTRICAL INSTRUCTIONS ALL ELECTRICAL WORK MUST BE DONE IN ACCORDANCE WITH ALL APPLICABLE ELECTRICAL CODES WARNING TURN OFF POWER AT SERVICE ENTRANCE BEFORE INSTALLING WIRING OR SERVICING THIS PRODUCT Note Opening in the top of the ironing center cabinet for the electrical supply wire is located 2 1 4 on center from left side of cabinet and 2 1 4 on center from the back of the cabinet 1 Remove the two screws from the electrical wireway cover Note Toward the top of the electrical wireway loose black and white pigtails are provided for hookup to the supply line 2 Remove the knockout at the wiring entrance location and install a romex connector where the knockout was removed 3 Determine the supply wire is ample to run from the top of the ironing center cabinet to the approximate location of the electrical pigtails A free wire length of approximately 48 is recommended 4 As y
Download Pdf Manuals
Related Search