Arrow AK600 Instructions / Assembly
Contents
1. 2 Kits are to be attached to Side Floor Frames Bend one flange on Gasenetdedls each of these Gussets before installing drill 1 8 3mm holes Side Gusset STEP 2 Installing Anchors 1 Make a Starter Hole in the ground for Anchor by inserting a long screwdriver or similar tool through the large hole in Gusset and into the ground Push tool straight down into the ground approximately 10 25cm at each N Anchor Remove the tool and soak the ground at Bend the Starter Holes with water One Flange Flat NOTE If ground is very loose sandy or contains Before Installing rocks refer to the Helpful Hints 2 Move Floor Frame away from Starter Holes to install Anchors in the ground 3 Insert sharp point of Anchor into Starter Hole Keep a steady downward pressure on Anchor while turning it clockwise into the ground Use a 1 2 13mm steel bar iron pipe or similar tool through the eye of the Anchor Apply even pressure on both sides of the tool while turning Starter Hole IMPORTANT Anchor must go straight down into the ground Do not allow Anchor to angle or wander from the starting point Turn Clockwise 4 Anchors are at proper depth when there is 1 into ground 25mm space under the eye as shown 5 Move Floor Frame back in position over Anchors Turneach Anchor slightly as necessary to align eye with slots in Gusset so that Floor Frame will rest on the ground Starter Hole STEP 3 Tightenin2. Owner s Manual amp Assembly Instructions PUI Model No 697 60297 AK600 EARTH ANCHOR KIT FOR STORAGE ARROW BUILDINGS World s Leading Maker of Storage Buildings INTRODUCTION This Anchor Kit contains 4 anchors and is recommended for buildings no larger than 10 x 10 ft 8m x 3m Use two kits for larger buildings TOOLS REQUIRED Carpenter s Level ae 2 Phillips Screwdriver This a MD Not This Steel Bar or lron Pipe IMPORTANT FLOOR FRAME MUST BE LEVEL AND SQUARE BEFORE ANCHORING Follow the instructions supplied with your building to assemble the Floor Frame Place Floor Frame on level ground or on a prepared level building site If optional Floor Brace Kits and more than one Earth D gt Siew Anchor Kit will be installed attach Side Floor Frame Anchor ed Sd Retainer Gussets between Floor Braces 2 0 NOTE If your building has been assembled before anchoring Gusset refer to Helpful Hints Corner Anchor Carpenter s a Gusset Side Floor Frame Anchor Gussets 1 Z Floor Frame gt S i Limits Anchored Corner Anchor ie Floor Frame ENTRANCE of Building NOTE Two 2 Anchor Kits shown 704990300 Corner Gusset STEP 1 Installing Gussets 1 Attach a Gusset in each corner of Floor Frame NOTE On some Models it will be necessary to drill 1 8 8mm holes in the Floor Frame at each Anchor Gusset 2 All other Gussets
3. ere itis to be anchored b For easier access to Corner Gussets remove Corner Panel from one corner of building c Insert sharp point of Earth Anchor thru Hole in Gusset and into Starter Hole in ground Turn anchor clockwise into ground until eye is 1 4 6mm above the Gusset Place Retainer under eye and continue to turn anchor until eye is firmly against Retainer d Re install Corner Panel on building e Repeatthisprocedure ateach remaining corner Retainer Corner Gusset TO ORDER REPLACEMENT PARTS Should you need replacement parts please contact your local Store Parts List ANCHOR KIT MODEL NO 697 60297 AK600 66108 Earth Anchor 66110 Retainer 66109 10Ax1 2 Screw 8397 Corner Gusset 704990300 Instruction Folder
4. g the Anchors TIGHTEN ANCHORS ONLY AFTER BUILDING HAS BEEN ERECTED 1 Insert a Retainer tabs pointing down under the eye of each Anchor so that tabs drop into slot in Gusset Retainer must be flat against Gusset i boy f Turn Clockwise To 2 Turn Anchor clockwise until eye is firmly against Tighten Retainer DO NOT OVER TIGHTEN NOTE Each Corner Anchor can be tightened much easier with the Corner Panel removed from building IMPORTANT Re install each Corner Panel before removing another Corner Panel from building 1 HELPFUL HINTS Anchoring in very loose sandy or rocky gound It may be necessary to install anchors deeper in the ground Dig ahole approximately 12 30cm deep at each anchor location Install anchors in bottom of hole in same manner as Step 2 except as follows a Insert a short length of 1 8 3mm steel cable thru eye of anchor andsecure with a cable clamp as shown b Insert other end of cable thru Hole in Gusset c Insert a Retainer tabs pointing down with cable in slot d Pull cable taut and secure with a cable clamp as shown e Fill in the hole to ground level NOTE Cable and Cable Clamps are not supplied with Earth Anchor Kit These items may be purchased at most hardware stores 2 Anchoring a building that has been completely assembled Follow the instructions in Steps 1 thru 3 except as follows a Leave the assembled building on the prepared site wh
Download Pdf Manuals
Related Search