Waring Pro MG1200 Use and Care Manual
Contents
1. Make sure notch on sausage making ring aligns with notch in feed screw 2 Put the desired sausage attachment small or large into screw ring and screw onto the grinder feeder head Casing 3 Slide casing over the end of the sausage attachment Yi leaving approximately 2 overhanging the end of the attachment 4 Place seasoned meat into the large die cast hopper and turn the switch to sausage Push the meat into the opening in the large die cast hopper using food pusher until the mixture appears at the end of the sausage attachment Keep casing moist by watering frequently Turn the unit off and tie a knot at the end of the 2 casing overhang 5 Continue step 3 until all the meat has been used or the casing is approximately 2 from being completely full 6 Turn unit off remove the end of the casing from the sausage attachment and tie a knot in the open end of the casing 7 Sausage can be made to the desired length by twisting the casing at intervals NOTE CIRCUIT BREAKER amp REVERSE SWITCH Reset Button If the motor stops this may be due to jammed food Immediately switch the appliance to its off position and unplug it from outlet Press the reset button on the bottom cover to reset To clear the feed screw pulse the meat grinder in the reverse direction and releasing it quickly three times Then turn the meat grinder on again If the appliance should get jammed again you may need t2. 7 Place food on the large die cast hopper and use pusher to feed food through opening OPERATING INSTRUCTIONS Grinder Feeder Motor Unit 1 Attach grinder feeder head to 2 Insert feed screw into the motor unit Fit grinder feeder grinder feeder head head tightly into attachment NOTE Make sure feed opening Tighten the locking screw is fully inserted or knob by turning it clockwise cutting blade will not fit 3 Attach cutting blade to the 4 Place the cutting plate in end of the feed screw Make the grinder feeder head sure the cutting edge flat side of the blade is facing out 5 Tighten screw ring onto the grinder feeder head 6 Place large die cast hopper on Pusher top of grinder feeder head Aa Die Cast 7 Turn unit to GRIND or SAUSAGE 8 Using pusher slowly feed cubes 9 Once meat has gone through Screw Ring grinder turn unit off and unplug Remove screw ring cutting plate and cutting blade NOTE Meats can be seasoned before or after grinding TO MAKE SAUSAGES The sausage attachments allow you to blend meat and spices for homemade sausages NOTE To avoid over stretching and splitting the casing do not make the sausage too thick Keep casings moist by watering frequently The meat mixture will expand slightly during cooking Grinder Feeder f Head Screw Ring D Ring Sausage Attachment Insert sausage making ring into feed screw
3. or removing parts and before cleaning Never immerse motor unit in water or other liquid Wash all parts except motor unit by hand in hot soapy water using care when handling the sharp blades Rinse these parts with clear hot water then dry REMOVABLE PARTS ARE NOT DISHWASHER SAFE Wipe motor unit with a damp cloth Do not use harsh or abrasive cleaners Cutting blade and cutting plates should be coated with cooking oil after washing and then wrapped in grease proof paper to keep them lubricated and rust free NOTE Pusher has a lid Inside you can store sausage attachments sausage making ring and cutting plates Any other servicing should be provided by an authorized service representative 10 NOTES Trademarks or service marks of third parties used herein are the trademarks or service marks of their respective owners 2012 Waring Consumer Products 150 Milford Road East Windsor NJ 08520 www waringpro com Printed in China MG1200 IB 12WR132358
4. HWASHER SAFE PLEASE HAND WASH ONLY ASSEMBLING 1 Make sure appliance is unplugged while assembling 2 Fit grinder feeder head tightly into attachment opening Holding the head with one hand place the locking knob into the hole on the side of the attachment opening and tighten it clockwise 3 Place feed screw into grinder feeder head long end spindle first turn it slightly until it is set into motor housing 4 NOTE Position cutting blade onto feed screw shaft with the flat cutting surface facing out from the feed screw If it is not fitted properly meat will not be ground and the cutting plate may be permanently damaged 5 Position the desired cutting plate onto the flat side of the cutting blade Ensure that the notch of the cutting plate fits into the tab of the grinder feeder head 6 Secure screw ring to the end of the grinder feeder head by turning clockwise DO NOT over tighten the screw ring 7 Place large die cast hopper on the grinder feeder head HOW TO USE 1 Before first use wash all parts of the appliance 2 Place the appliance on a stable work surface 3 Make sure the grind sausage off reverse switch is in the off position and that the unit is fully assembled 4 Insert plug into wall outlet 5 Place a wide shallow bowl or plate beneath the grinder tube to catch food 6 Switch appliance to GRIND or SAUSAGE position The appliance must always be in GRIND or SAUSAGE position before adding food
5. WARING PRO PROFESSIONAL MEAT GRINDER MG1200 For your safety and continued enjoyment of this product always read the instruction book carefully before using IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed including the following 1 2 3 11 12 13 14 15 16 READ ALL INSTRUCTIONS Unplug from outlet when not in use before putting on or taking off parts and before cleaning To protect against risk of electrical shock do not immerse main unit or power cord in water or other liquid Close supervision is necessary when any appliance is used by or near children This appliance is not recommended for use by children Avoid contact with moving parts Wait until moving parts have stopped running before you remove the parts of the appliance Never put the unit on or near a hot burner in an oven or ina dishwasher Do not operate the appliance or any other electrical equipment with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner Return to the nearest authorized service center for examination repair or adjustment Never feed food by hand always use the food pusher Keep hands hair clothing and utensils away from moving discs during operation to reduce the risk of personal injury and or damage to the appliance Do not use outdoors or use for other than intended use Warning the cutti
6. d into wall outlet To disconnect turn the control to OFF then remove plug from wall outlet Do not operate your appliance in an appliance garage or under a wall cabinet When storing in an appliance garage always unplug the unit from the electrical outlet Not doing so could create a risk of fire especially if the appliance touches the walls of the garage or the door touches the unit as it closes DO NOT operate the grinder without the hopper in place DO NOT attempt to grind bones nuts or other hard items This appliance is for 120 volts only and should not be used with a converter SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY PARTS 1 ONDA wD Grind Sausage Off Reverse Switch Locking Knob Motor Unit Attachment Opening Food Pusher with Lid Large Die Cast Hopper Grinder Feeder Head Feed Screw NOTE Cutting plates sausage attachments and sausage making ring are stored in food pusher 14 10 11 12 13 14 15 16 17 Cutting Blade Cutting Plate fine Cutting Plate medium Cutting Plate coarse Sausage Attachment large Sausage Attachment small Sausage Making Ring Screw Ring Reset Switch not shown CUTTING PLATES Fine Cutting Plate Great for spreads pates baby food and hamburgers Medium Cutting Plate Great for ground meat used in soups or for relishes Coarse Cutting Plate Great for ground meat used in chili or for vegetables ALL PARTS ARE NOT DIS
7. ng blade is sharp handle with care both when using and when cleaning Do not let cord hang over edge of table or counter contact sharp edges or touch hot surfaces Do not pull on the power cord to disconnect Never plug in the appliance where water may flood the area Place the appliance on a firm and stable surface NEVER PUT YOUR FINGERS NEAR THE FOOD CHUTE WHILE GRINDER IS IN OPERATION Ensure that the appliance is not placed close to the edge of the table worktop etc where it can be pushed off or fall 2 17 18 19 20 21 22 23 24 25 26 27 The use of attachments not recommended or sold by the manufacturer may cause fire electric shock or injury Never use abrasive cleaning agents or abrasive cloths when cleaning the unit Do not use fingers to scrape food away from cutting blade while appliance is in operation Cut type injury may result Use the unit only when completely assembled Do not leave the appliance unattended while it is running Before using for the first time remove all packaging and wash parts This appliance has a polarized plug one blade is wider than the other To reduce the risk of electric shock this plug will fit in a polarized outlet only one way If the plug does not fit the outlet perfectly reverse the plug If it should still not fit contact a qualified electrician Do not modify the plug in any way Check that the control is OFF before plugging the cor
8. o switch it off unplug disassemble the grinder feeder head and clean the internal parts Press the reset button before turning the meat grinder on again Important Always switch the unit to its off position before pressing reset button to reset and unplug it from outlet HELPFUL HINTS e Grinding stale bread pieces may help remove food residue left in the appliance after use e Cut food into strips or cubes slightly smaller than the opening on the large die cast hopper e Make sure food is free of bone tough tendons nutshells etc before grinding e Raw meat and fish should be thoroughly chilled not frozen before grinding to reduce the loss of juices e Freshly ground meat should be refrigerated and cooked within 24 hours e During extended grinding fats from meats can build up inside the grinder tube slowing down grinding and straining the motor If this happens you should stop the appliance wash parts in hot water and reassemble When possible alternate bread with meat This helps keep the feed screw clean e Trim a handful of fat from meat Process the fat through the hopper to lubricate grinding mechanism for better processing results e For best drying results prepare sausage a day or two prior to use e When using the large sausage attachment it is not necessary to use the sausage making ring See page 4 part 15 CLEANING AND MAINTENANCE Always unplug motor unit when not in use before inserting
Download Pdf Manuals
Related Search