Magic Chef MCO165UW Installation Guide
Contents
1. Install the grease filters C Recirculation Ventilation System Your over the range microwave oven has been provided with a charcoal filter for a recirculation venting application on some models If replacement of the charcoal filter is required contact your DAEWOO authorized dealer C 1 Ventilation motor This ventilation motor has been assembled for Recirculation exhaust C 2 Install the Mounting plate See the page 5 A 2 Install the mounting plate C 3 Mounting Microwave oven See the page 6 A 3 Mounting the Microwave oven You need not use damper for recirculation C 4 Install the Charcoal filter To remove the charcoal filter disconnect power at the main fuse or circuit breaker panel or pull the plug Remove the screws on the front of the grille and remove the grille Install the charcoal filter Replace the grille and screws Charcoal Filter Grille Checklist for Installation 1 Make sure oven has been installed according to these instructions and top cabinet template 2 Remove all packing material from the oven 3 Plug in power cord 4 Read Use and Care manual 5 Keep installation instructions and template for the local electrical inspector s use MCO160UW B Q S2. Microwave Oven Installation M anual IMPORTANT SAFETY INSTRUCTION Never operate the oven when it is empty or without the glass turntable Introduction Your Over the Range microwave oven comes complete with an installation instruction kit which contains the following three pieces of information required to install it I This installation instruction booklet complete with diagrams on preparing your cabinets and microwave oven for installation II The Top Cabinet Template used to locate the power cord clearance hole cabinet mounting holes and the vertical exhaust location Ill Instead of The Wall Mount Template Wall Mounting Plate used to locate the mounting plate holes and to locate the horizontal exhaust location Please read all of the instructions thoroughly before installing your microwave oven NOTE IT IS RECOMMENDED THAT TWO PEOPLE INSTALL THIS PRODUCT IMPORTANT KEEP INSTRUCTIONS FOR LOCAL ELECTRICAL INSPECTOR S USE Important Safety Information Grounding Instructions This appliance must be grounded In the event of an electrical short circuit grounding reduces the risk of the electric shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded WARNING Improper use of the grounding can result in a risk of electr
3. WEIGHT OF 135 POUNDS CAUTION FOR PERSONAL SAFETY THIS PRODUCT CANNOT BE INSTALLED TO CABINET ARRANGEMENT S SUCH AS AN ISLAND OR A PENINSULA IT MUST BE MOUNTED TO BOTH A TOP CABINET AND A WALL Electrical Requirements Product rating is 120 volts AC 60Hertz 15 amps and 1600 1700 watts This product must be connected to a supply circuit of the proper voltage and frequency Wire size must conform to the requirements of the National Electric Code or the prevailing local code for this kilowatt rating The power supply cord and plug should be brought to a separate 20ampere branch circuit single grounded receptacle The outlet box should be located near the cord entry point The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electric Code or the prevailing local code Power supply cord a A short power supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord b Longer cord sets or extension cords are available and may be used if care is exercised in their use c If a long cord or extension cord is used 1 The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance 2 The extension cord must be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled
4. a section of straight duct which is longer than their actual physical size When calculating the total duct length add the equivalent lengths of all transitions and adaptors plus the lengths of all straight duct sections The diagram below shows the approximate feet of equivalent length of some typical ducts Roof Cap 24Ft 90 Elbow 10Ft 45 Elbow 5Ft Rectangular to Round Transition Adaptor 5Ft Wall Cap 40Ft 90 Elbow 25Ft Lh ES Ventilation system Instructions Your Over the Range microwave oven is designed for adaptation to the following three types of ventilation Select the type of ventilation required for your installation and proceed to the appropriate section A Horizontal Ventilation System A 1 Ventilation motor This blower motor has a damper and your microwave oven is shipped assembled for a Recirculation Application Step 1 Step 4 Remove the screws 1 for opening the blower motor cover Place the blower unit into the opening and secure it to the oven and save screw Remove cover with the screw 3 from step 2 Blower Motor Cover Secure the Case Blow Fan Top to the Case Blow Fan under with the screw 2 from step 2 Fan Blade Openings Facing Rear Step 2 Remove the screws 2 and 3 for Case Blow Fan Top and Blower attachment and save screws sooni Remove Case Blow Fan Top E Lift blower unit out of mountin
5. 66 or more from the floor to the top of the microwave oven NM max 12 Back splash Your Over the Range microwave oven requires mounting space on a wall as shown 1 A minimum of 30 between wall hung side cabinets is required for installation Make sure the bottom edge of the top cabinet is at least 66 from the floor and 30 from the cooking surface And the depth of the cabinet is required less than 12 inch max 12inch 2 For easier access to the hood lamp the bottom of the microwave oven should be at least 2 above the range backsplash 3 If you are going to vent your microwave oven to the outside see exhaust duct preparation 4 Designed to be installed in 30 wide cabinet opening Wall Construction Your Over the Range microwave oven should be mounted against and supported by a flat vertical wall Wall construction should be a minimum of 2 x 4 wall studding and 3 8 or more thick drywall or plaster lath The oven must be attached to a minimum of one 2 x 4 wall stud For proper installation the wall must be capable of supporting the cabinet load plus a minimum of 135 pounds the 85 pound weight of the microwave oven and load weight allowance of 50 pounds To find studs use one of the following methods 3 8 Drywall or Plaster Lath in these area LA Usually 16 or 24 S LI p a ge Lag screws must be
6. OP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through e Read the instructions on the TOP CABINET TEMPLATE e Tape it underneath the top cabinet e Drill the holes following the instructions on the template NOTE TOP CABINET TEMPLATE instruction must be installed to proceed Step 1 Protect the top of your range by placing a portion of the carton or some other heavy material over the cooking surface before mounting your oven Step 2 Lift the microwave oven and tilt it forward Hang the unit on two tabs at the bottom of the mounting plate Step 3 Thread power cord through the hole at the bottom of the top cabinet Swing the unit upward to meet the top of the mounting plate and hold it securely Cabinet Step 4 Insert 2 bolts through 2 flat washers into holes on top cabinet floor Tighten screws to close the gap between top cabinet and the microwave oven NOTE MICROWAVE OVEN MUST BE SECURED WITH TWO MOUNTING BOLTS Dress power cord nearly in top cabinet Install the grease filters Using filler block for recessed bottom cabinet insert a bolt with a 3 4 washer into one of the holes drilled previously in the top cabinet floor D amp Eon Top Cabinet Template Top cabinet Washer mounting screw Cabinet bottom shelf Microwave oven top B Vertical Ventilation System B 1 Ventilation
7. g location CAUTION Do not pull or stretch blower wiring first BEFORE Fan Blade Openings Case Blow Fan Under Case Blow Fan Top Facing Front Back of Oven iN Blower Motor Carefully match the exhaust opening location of the microwave y pening t and attach the damper to the rear plate by sliding it into the guides at the rear plate A A p IE back rear of unit If you want VERTICAL roll the blower unit so that the fan After adjust the damper reinstall the blower motor cover with blade openings are facing upward the screw Step 3 Roll the blower unit so that the fan blade openings are facing Back of Oven CAUTION Wires to blower unit must be routed avoid to B pinching before reinstallation of cover plate e sure that the damper hinge is on the top and the damper swings free into the wall outlet Before Rollin X y After Rolling 7 S Ma Fan Blade Openings R NU Facing Rear Roll the blower motor clockwise 180 A 2 Install the Mounting Plate Step 1 Setup position a Draw a line down the middle of the studs See the Wall Construction page 3 b Draw a vertical line on the wall at the center of the 30 wide space NOTE Use the wall template for the rear wall Reference Wall Template prior to proceeding Installation of this product require 2 persons Step 2 Drilling Reference the Wall Template Power Supply Cord Hole House Duct Mounti
8. ic shock Consult a qualified electrician or serviceman if the grounding instructions are not completely understood or if doubt exists as to whether the appliance is properly grounded and either 1 If it is necessary to use an extension cord use only a 3 wire extension cord that has a 3 blade grounding plug and a 3 slot receptacle that will accept the plug on the appliance The marked rating of the extension cord shall be equal to or greater than the electrical rating of the appliance or Do not use an extension cord 2 If the power supply cord is too short have a qualified electrician or serviceman install an outlet near the appliance Safety Instructions This product requires a three prong grounded receptacle The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded If not properly grounded or if the outlet box does not meet the electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies CAUTION FOR PERSONAL SAFETY REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION TO AVOID SEVERE OR FATAL SHOCK INJURY CAUTION FOR PERSONAL SAFETY THE MOUNTING SURFACE MUST BE CAPABLE OF SUPPORTING THE CABINET LOAD IN ADDITION TO THE ADDED WEIGHT OF THIS 85 POUND PRODUCT PLUS ADDITIONAL OVEN LOADS OF UP TO 50 POUNDS OR A TOTAL
9. installed I Stud finder a magnetic device which locates nails II Using a hammer tap lightly across the mounting surface gt 2X4 wood stud or metal stud rN 25 gauge or thicker to find a solid sound This will indicate a stud installation After locating the stud s the center can be found by Probing the wall with a small nail to find the edges of the stud and then placing a mark half way between the edges The center of any adjacent studs should be 16 or 24 from this mark IL Draw a line down the center of the studs Hood Exhaust Duct Outside ventilation requires HOOD EXHAUST DUCT Read the following carefully EXHAUST CONNECTION The hood exhaust has been designed to mate with a standard 3 1 4 x 10 rectangular duct If round duct is required a rectangular to round transition adapter must be used Do not use less than a 6 diameter duct REAR EXHAUST If rear or horizontal exhaust is to be used care should be taken to align exhaust with space between studs or wall should be prepared at the time it is constructed by leaving enough space between wall studs to accommodate exhaust MAXIMUM DUCT LENGTH For satisfactory air movement the total duct length of 3 1 4 x 10 rectangular or 6 diameter round duct should not exceed 140 feet of equivalent duct run ELBOWS TRANSITIONS WALL AND ROOF CAPS etc present additional resistance to air flow and are equivalent to
10. motor Step 1 and 2 See the page 4 A 1 Ventilation motor Step 3 Roll the blower unit so that the fun blade openings are facing upward Fan Blade Openings Facing Up Before Rolling wR Ss After Rolling Back of Oven Roll the blower motor clockwise 90 Step 4 Place the blower unit into the opening Secure the Case Blow Fan Top the blower motor and cover to the microwave oven with the screw 1 2 and 3 from step 1 and 2 Filler block Carefully match the exhaust opening location of the microwave and attach the damper to blower motor cover by sliding it into the guides at the blower motor cover Be sure that the damper hinge is on the front and the damper swings free into the wall outlet B 2 Install the mounting plate See the page 5 A 2 Install the mounting plate B 3 Mounting Microwave oven See the page 6 A 3 Mounting the Microwave oven B 4 Adjust the Damper For the vertical exhaust open the top cabinet and adjust the damper to the microwave through the cabinet bottom For front to back or side to side adjustment slide the damper as needed With the damper out twist the damper to fit under the flaps of the blower plate Replace the damper and make sure it will move easily by the force of the exhaust air B 5 Connecting Ductwork Extend the house duct down to connect to the exhaust adapter Seal exhaust duct joints using duct tape House Duct
11. ng Plate Step 3 Tightening the screws To Attach the mounting plate to the wall using the toggle bolt assemblies and or lag screws a Insert toggle bolts through mounting plate at required locations and add the spring loaded toggles Be sure you leave space at least the thickness of the wall between the mounting plate and the end of the toggle nut in closed position If you do not leave this space the toggle nut will not open on the other side of the wall b Position mounting plate on wall and insert toggle bolt assemblies through the drywall holes or start the lag screw s through the wall stud s c Next secure mounting plate to the wall by tightening toggle bolt assemblies or lag screw s Space more than wall thickness BE N homo YE O a a wee 7 Vi Mounting plate 7 Dry Wall d Drill 3 16 diameter lag screw hole s into one or more wall studs Remember you must have at least one lag screw into a wall stud For stud location refer to WALL CONSTRUCTION see page 3 e Tighten the lag screw S into wall stud S A 3 Mounting microwave oven NOTE IT IS VERY IMPORTANT THAT THIS OVEN BE INSTALLED BY TWO PEOPLE IMPORTANT DO NOT GRIP OR USE HANDLE DURING INSTALLATION PREPARATION OF T
12. on by children or tripped over unintentionally This over the range oven was designed for use over ranges no wider than 30inches It may be installed over both gas and electric cooking equipment Installation Hardware The following is a list of parts you may need for installing your Over the Range microwave oven You will find the installation hardware contained in a packet with the unit Check to make sure you have all these parts Use this time to become familiar with each piece Image Part amp Description Q ty Image Part amp Description Q ty L ma mm Gos 3 ae Top Cabinet Template 1 O ae and Nuts 3 Wall Template Rear Wall Template 1 binet Mounting Bolt nstallation 1 en Pa Bee ot 18 stn Installation Manul 1 Wash az se an REAA 3 Cae Use and Care Manual 1 Nylon Grommet AN for metal cabinets 2 C gt Roller Guide l Dare 1 Grease Filters 2 Tools The following tools may be needed for installation of your microwave oven Phillips screwdrivers Electric Drill Motor 1 2 amp 5 8 Wood Bits amp 3 16 Drill Bit Saw to cut exhaust opening if needed or Jig Saw Tin Snips if needed Pencil Tape Measure Paper Tape amp Duct Tape Mounting Space i 28 30 more than from cooking surface
Download Pdf Manuals
Related Search