Trex WGFGATEKIT Installation Guide
Contents
1. and parallel STEP 4 MAKE ANY FINAL ADJUSTMENTS TO THE GATE HINGE AS NEEDED Opening for Large Size Trex Gate panel should A To adjust a sagging gate or to shift panel in the opening loosen the hinge nuts with an 11 16 wrench be 65 3 4 For custom size gates opening is 1 7 8 larger than the gate panel width B Loosen or tighten the nuts in the direction shown below Lift or push panel to slide the hinge x xk Note If Hinge Post is not connected to a fence panel 46 1 4 C Retighten the hinge nuts it may be necessary to use a Heavy Steel Post D Due to weather and temperature changes periodic hinge adjustment may be necessary to assure proper latch Stiffener or to fill the post with concrete for additional connection f f strength Shift panel left Shift panel right Raise latch side Lower latch side Re 30 Top Top Top Top B Tim i we Hinge Hinge Hinge Ti in me Hinge r lt gt gt lt 2013 TFSC Bottom Bottom Bottom Bottom e B m a S K m S i wA O Hinge wO Hinge wO Hinge wO Hinge lt _ gt lt gt2. TREX SECLUSIONS TREX SECLUSIONS GATE INSTALLATION GUIDE GATE INSTALLATION GUIDE SECLUSIONS GATE COMPONENTS STEP 2 INSTALL THE GATE PANEL A Seclusions 5x5 fence post A Attach the hinges to the gate panel approximately 6 from the top and bottom of the gate using a 3 8 nut driver and the 4 1 1 2 supplied self tapping screws Pre drilling with a 3 16 drill bit will make installation easier g Seclusions fence gate c Steel post stiffener Note Install hinges on the side of the gate that you want the gate to swing toward Seclusions fence hinge 2 5 B Place the gate panel in the opening Adjust the gate to be level and to the desired height by placing blocks under gate panel Allow ample clearance for full swing of gate eee direction C Using 4 1 1 2 supplie self drilling screws attach each Lis es e Seclusions fence latch e Seclusions striker Gc Seclusions gate handle 2 hinge to the steel inserted gate post Pre drilling with a 3 16 drill bit will ease installation 14 1 1 2 self tapping screws 20 D Open the panel and attach the inside corner of the bracket to the gate post 1 self tapping screws 14 m Adjust hinges using the method described below so that there is a minimum of 1 clearance between the gate panel and gate post BEFORE YOU BEGIN Read all instructions before installation Looking for a unique gat
3. e The flexibility of Trex makes creating a custom gate achievable limited only by one s imagination For a customized gate please consult your local Trex Fence dealer Follow Trex Seclusions Installation Instructions to lay out fence and dig holes STEP 1 SET THE GATE POSTS STEP 3 ATTACH THE LATCH AND HANDLES A Attach the latch to the latch post approximately 36 from the ground using 6 1 1 2 supplied self tapping screws The catch is to be placed in the direction of the gate swing The catch may face up or down depending on the direction of gate swing Note Due to concrete cure times set the gate posts 2 3 days before gate is installed A A Slide the Steel Post Stiffener into the Hinge post B Using the 4 1 1 2 supplied self drilling screws attach the Open side of insert should face away from gate striker to the gate panel lining the striker rod up with the catch opening on the post latch C Attach gate handles to the gate panel using 2 1 supplied self tapping screws Handles should be attached 1 3 4 from HINGE POST the edge of the gate panel The height must be staggered front and back as shown B Set posts into post holes that are 30 deep or to frost line by 12 wide C Opening measuring from inside edge of post to inside edge of post for Standard Size Trex Seclusions Gate panel should be 46 1 4 Inside Check for level faces should be plumb
Download Pdf Manuals
Related Search