Genie 37335R Instructions / Assembly
Contents
1. return a Remote Button to its original Intellicode 1 mode 1 Slide the Circuit Board Cover off FIG 3 2 Press the DEFAULT button the yellow LED will flash 3 Press the Remote Button you wish to reprogram Its now Intellicode 1 again FCC amp IC CERTIFIED This device complies with part 15 of the FCC Rules and ICRSS 210 Issue 8 a Re orient or relocate the receiver antenna b increase the separation between the opener and rece d Consult your local dealer Any modifications or changes to this equipment which are not expressedly a 59059 vi Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmfuf interference to radio communications However there is no guarantee that interference will not occur in a particular situation this equipment does cause harmful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try and correct the interference by one or more of the following measures iver c Connect the opener into an outlet on a circuit different fram that which the receiver is connected and proved by The Genie C2. 37384500131 GenielVlaster TRANSMITTER OPERATION o A SCWARNING E Moving door can cause serious injury or death Do Not install transmitter unless the door operator s safety reverse works as required by the door operator s manual Wall control must be mounted in sight of door Keep people clear of opening while door is moving Do Not allow children to play with the transmitter or door operator if safety reverse does not work properly Close door then disconnect operator using the manual release handle Do Not use transmitter or door operator 7 Refer to Door and Door Operator Owner s Manuals before attempting any repairs A For use with Intellicode 1 Openers The Universal Remote comes from the factory in the Intellicode 1 Operating Mode The Intellicode 1 Mode is indicated by a RED LED on the remote whenever a button is pressed FIG 2 Program it as you would any Intelficode 1 remote using the following steps 1 Locate the Learn Code Button and Learn Code indicator LED on your opener s powerhead FIG 1 See owner s manual 2 Press and release the Learn Code Button the Learn Code LED will blink rapidly 3 Press and release a Remote Button FIG 2 the Learn Code LED will stay on stops blinking 4 Press and release the same Remote Button again the Learn Code LED will turn off 5 Press and release the same Remote Button again the Door Opener will run NOTE Each opener mus
3. ompany could void the user s authority to operate the equipment FIG 1 POWERHEADS for various models Circle shows location of Learn Code Button and LED PRIOR TO 1995 AND INTELLICODE D FRONT CODE SWITCH TYPE Noga gR FIG 2 LEDs red green REMOTE BUTTONS NON ROLLING CODE BUTTONS YELLOW LED REAR COVER INSIDE REAR COVER FOR HELP OR ANSWERS TO QUESTIONS CALL 800 354 3643 or visit www geniecompany com
4. orking code switch remote simply match your new GenieMaster Remote switches to those on your existing remote and proceed to step 4 FIG 3 To operate a Code Switch equipped operator 1 Open the opener s light lens in order to gain access to its row of Code Switches hese are 3 position switches and 0 2 Slide off the rear cover of the remote FIG 3 3 Set the Code Switches positions in the remote to match those of the switches in the opener If you are working with a 9 switch operator set the remote switches 10 11 and 12 to the center or 0 position 4 Locate the non rolling code button label inside the Rear Cover FIG 3 5 Press the non rolling code button B C or D FIG 3 that matches the appropriate code switch description on the label The YELLOW LED next to the battery will begin flashing 6 Press and release the Remote Button you want to assign to that opener the GREEN LED on the remote will flash for approximately 2 seconds and stop 7 Pressing the same button again will operate the opener The RED LED on the remote will flash while the button is pressed D Replacing the Battery Programming is not affected by battery replacement 1 Slide the Circuit Board Cover off the back of the remote FIG 3 2 Slide the old battery toward the bottom of the remote and out 3 Properly discard the old battery 4 Slide a new 2032 size battery into position and slide the Cover back on E Resetting the Remote To
5. t have its own assigned Remote Button To program additional openers repeat the steps above using a different Remote Button B For use with Intellicode 2 Openers p The button or buttons on your remote that you wish to use to operate Intellicode 2 openers must be switched to the Intellicode 2 Operating Mode The Intellicode 2 Mode is indicated by a GREEN LED on the remote whenever a button is pressed FIG 2 To shift to Intellicode 2 mode 1 Press and hold the chosen Remote Button A steady RED LED will be illuminated and after 10 seconds a GREEN LED will also illuminate 2 Release the button 3 Press and release that same button again TWICE the remote s LEDs will both turn off 4 Press and release that same button again the remote s GREEN LED will light while you press that button indicating it is now in Intelficode 2 mode To program the remote to an opener 1 Press and hold the PROGRAM SET FIG 1 button on opener s powerhead for 2 seconds or until the round LED turns BLUE When you release the button the BLUE LED will go out and the LONG LED will turn PURPLE 2 Press and release the Remote Button you want to assign to that opener 3 Press and release that same button After releasing the button the second time the LEDs will both be off 4 Press and release that same button again the Door Opener will run C For use with Openers having a row of Code Switches 9 or 12 switches if you already have a w
Download Pdf Manuals
Related Search