JET 333620 Use and Care Manual
Contents
1. 17 Anvil Diameter r 7 9 8 tds T4 79 8 7 18 Ram Dimension SIA SQ iiit 59 2 2 Sq Net Weight 16 1 2 Ibs 24 1 4 Ibs 64 Ibs 105 248 Ibs The above specifications were current at the time this manual was published but because of our policy of continuous improvement Walter Meier Manufacturing Inc reserves the right to change specifications at any time and without prior notice without incurring obligations AWARNING Read and understand the entire contents of this manual before attempting assembly or operation Failure to comply may cause serious injury Arbor Press Features The arbor press see Exploded view on page 8 consists of a cast iron base an anvil a pressing handle with lock knob and a rack type ram The removable anvil has four cutouts that can be used for pressing off or pressing on bearings or bushings of various sizes Set up and Operation Note The item numbers provided in the procedures that follow correspond with the item numbers in the exploded view in the Replacement Parts section see page 8 AWARNING Do not use the arbor press without first securing the arbor press to the workbench and anchoring the workbench to the floor Mount the arbor press to the workbench or stand and secure with bolts using the holes in the base 1 Also2. J E T Operating Instructions and Parts Manual Arbor Press 1 2 3 5 Ton Model No APO M AP1 M AP2 M AP3 M AP5 M WALTER MEIER Manufacturing Inc 427 New Sanford Road LaVergne Tennessee 37086 Part No M 333605M Ph 800 274 6848 Revision A 05 2011 www waltermeier com Copyright 2011 Walter Meier Manufacturing Inc Warranty and Service Walter Meier Manufacturing Inc warrants every product it sells If one of our tools needs service or repair one of our Authorized Service Centers located throughout the United States can give you quick service In most cases any of these Walter Meier Authorized Service Centers can authorize warranty repair assist you in obtaining parts or perform routine maintenance and major repair on your JETetools For the name of an Authorized Service Center in your area call 1 800 274 6848 MORE INFORMATION Walter Meier is consistently adding new products to the line For complete up to date product information check with your local Walter Meier distributor or visit waltermeier com WARRANTY JET products carry a limited warranty which varies in duration based upon the product MW Metalworking WW Woodworking Body Repair Kits Beam Clamps Bottle Jacks Chain Hoist Cable Pullers Manual Cold Saws 1 Lever Hoists YEAR Hoists Air Pullers JCH Models A Hoists Electric Palet Trucks Scissor Lift Tables WW Drill Presses Fastening Tools varied cian Metal forming Rig
3. secure the workbench or stand to the floor Changing Ram Position The ram has a flat surface on one end and a hole on the other end The hole is used to accept the punch inserts Change out the ram as follows A Remove the handle by loosening the knob 17 Then remove one cap 5 from the handle assembly Remove handle 6 from the pinion 16 B Remove the pinion retainer 14 by backing off the Set Screw 13 Now slide the pinion retainer 14 off of the pinion 16 C Pull up on the ram 4 enough to provide slack to remove the pinion 16 from the arbor press D Pull the ram 4 out the top of the arbor press body Turn the ram 4 end for end Hint if ram does not freely come out of arbor press body loosening the two hex nuts 11 on side of arbor press body and the two hex nuts 11 on the front plate 12 E Repeat steps D in reverse Maintenance A Periodically lubricate the arbor press with a light machine oil B Wipe off or vacuum the accumulated debris and dust after using the arbor press C Periodically check the ram for side to side and front to back play If the play is excessive loosen the hex nuts 11 and adjust tighten the screws 10 on side 9 in front just enough to eliminate the excess play Tighten them equally to assure even contact with the ram 4 D Once the play is eliminated hold the screw 10 or 9 in position and tighten the hex nut 11 Check to make sure the amoun
4. 8 2206 TS 1550044 Washer M6G 4 uiuat TS 1482051 Bolt Hex M6x25 2 TO ss TS 1482061 Bolt Hex M6x30 2 jo pv TS 1540044 Nut Hex M6 4 121 5 AP1 12 Plates iue 1 TS 1523011 SHSS M6xX6 1 i SA AP1 10 Pinion Retainer 1 TS 1482021 Bolt Hex M6x12 1 16 AP1 03 Pinion 1 T4535 AP1 05 KNOB cer eret 1 18 TS 2361061 Lock Washer M6 4 e AP1 19 ID Label not shown 1 Model AP2 M 2 ton Arbor Press Index Part No Description Qty AP2 01 1 AP2 06 eS 1 AP2 16 Spring Pin 6 25 1 AP2 02 1 AP2 5 1 2 AP2 6 1 Handle 1 Vases TS 1490051 Bolt Hex M8x30 4 Bt TS 1550061 Washer M8 4 Bolt Hex 8 30 2 Bolt Hex M8x30 2 Nut Hex MB 4 Plata ins 1 SHSS M6x6 1 Pinion Retainer 1 Bolt Hex M8x16 1 Pinion 1 Knob 1 Lock Washer M8 4 Model AP3 M 3 ton Arbor Press Index Part No TS 1490051 TS 1490051 Description Qty Basn cee SENA 1 An
5. TATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL CONTINGENT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU Walter Meier sells through distributors only The specifications in Walter Meier catalogs are given as general information and are not binding Members of Walter Meier reserve the right to effect at any time without prior notice those alterations to parts fittings and accessory equipment which they may deem necessary for any reason whatsoever JETe branded products are not sold in Canada by Walter Meier 2 Table of Contents Warranty Service RR 2 Table of Conte Sennen eneee n renr ne r a N ner ner aan aaar eanan Dear ean anoir apupa aat 3 DRE a E ote E ne 4 ex ni aa na a a cn cava cece E E T N 5 Specifications em 5 Arbor Press Features reet Rak aana ASAA aa EATR CREE EREE 6 Se t up and OperatiOn 2 aaan ansaid saints 6 Changing Ram Position 6 Manora S ENRICO E E 6 tz is HESSE aE a a a TTE 7 o T V I E T T EM M M MM M M MU T 8 The specifications in this manual are given a
6. e floor or bench before use Check damaged parts Before further use of the arbor press a part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced Provide for adequate space surrounding work area and non glare overhead lighting Keep the floor around the arbor press clean and free of scrap material oil and grease Make your workshop child proof with padlocks master switches or by removing starter keys Give your work undivided attention Looking around carrying on a conversation and horse play are careless acts that can result in serious injury Maintain a balanced stance at all times so that you do not fall into the arbor press Do not overreach or use excessive force to perform any machine operation Use recommended accessories improper accessories may be hazardous Make sure the work piece is securely attached or clamped to the table Remove loose items and unnecessary work pieces from the area before starting the machine Do not overload the arbor press by using extension cheater bars Use steel collars to support parts when pressing on bearings to prevent damage to the bearings Familiarize yourself with the following safe
7. ging Equip WW Benchtop Screw Jacks WW Dust Collectors sero bu Hand Tools lachine Accessories Contractor Riese Mobile Bases Air Tools Industrial MilDrlls Service Jacks Tools Trolleys Geared WW Dust Filters Striking Tools s Milling Machines Stackers Trolleys Plain WW Dust Fittings Safety Equipment Air Tools Light MW Bandsaws Surface Grinders Winches Manual WW Jointers Specialty Items Industrial MW Drill Presses Tapping WW Air Filtration WW Lathes Vise Accessories Lubrication MW Finishing Trolleys Air WW Bandsaws WW Planers WW Shapers Equipment Trolleys Electric WW Buffers WW Sanders WW Tablesaws MW Lathes Web Slings MW Precision Vises Winches Electric Vises no precision Clamps Warranty reverts to 1 Year Warranty if woodworking WW products listed above are used for industrial or educational purposes WHAT IS COVERED This warranty covers any defects in workmanship or materials subject to the exceptions stated below Cutting tools abrasives and other consumables are excluded from warranty coverage WHO IS COVERED This warranty covers only the initial purchaser of the product WHAT IS THE PERIOD OF COVERAGE The general JET warranty lasts for the time period specified in the product literature of each product WHAT IS NOT COVERED Five Year Warranties do not cover woodworking WW products used for commercial industrial or educational purposes Woodworking products with Five Year Warranties that are used for c
8. ommercial industrial or education purposes revert to a One Year Warranty This warranty does not cover defects due directly or indirectly to misuse abuse negligence or accidents normal wear and tear improper repair or alterations or lack of maintenance HOW TO GET SERVICE The product or part must be returned for examination postage prepaid to a location designated by us For the name of the location nearest you please call 1 800 274 6848 You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise If our inspection discloses a defect we will repair or replace the product or refund the purchase price at our option We will return the repaired product or replacement at our expense unless it is determined by us that there is no defect or that the defect resulted from causes not within the scope of our warranty in which case we will at your direction dispose of or return the product In the event you choose to have the product returned you will be responsible for the shipping and handling costs of the return HOW STATE LAW APPLIES This warranty gives you specific legal rights you may also have other rights which vary from state to state LIMITATIONS ON THIS WARRANTY WALTER MEIER MANUFACTURING INC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT EXCEPT AS STATED HEREIN ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED SOME S
9. s general information and are not binding Walter Meier Manufacturing Inc reserves the right to effect at any time and without prior notice changes or alterations to parts fittings and accessory equipment deemed necessary for any reason whatsoever Warnings 10 11 Keep visitors a safe distance from the work area Keep children away 13 14 15 Read and understand the entire owners manual before attempting assembly or operation Read and understand the warnings posted on the machine and in this manual Failure to comply with all of these warnings may cause serious injury Replace the warning labels if they become obscured or removed This arbor press is designed and intended for use by properly trained and experienced personnel only If you are not familiar with the proper and safe operation of an arbor press do not use until proper training and knowledge have been obtained Do not use this arbor press for other than its intended use If used for other purposes Walter Meier Manufacturing Inc disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use Always wear approved safety glasses face shields while using this arbor press Everyday eyeglasses only have impact resistant lenses they are not safety glasses Do not operate this arbor press while tired or under the influence of drugs alcohol or any medication Make sure this arbor press is firmly secured to th
10. t of play is acceptable Parts Lists Model APO M 1 2 ton Arbor Press Index Part No Description Qty Tianan APO 01 Base 1 E 06 1 APO0 16 Spring Pin 6x16 1 duni 02 1 0 5 1 Gapuvessnemenumems 2 6 5 APO 6 1 Handle 1 ee TS 1482051 Bolt Hex M6x25 4 Bonos TS 1550044 Washer M6G 4 o TS 1482051 Bolt Hex M6x25 2 10 TS 1482061 Bolt Hex M6x30 2 TT TS 1540044 Nut Hex M6 4 12 AP0 12 Plate eere 1 TS 1523011 SHSS M6X6 1 14 APO 10 Pinion Retainer 1 TS 1482021 Bolt Hex M6x12 1 16 03 Pinioni om 1 T l APO 05 Knob o tees 1 18 TS 2361061 Lock Washer M6 4 19 0 Label not shown 1 Model AP1 M 1 ton Arbor Press Index Part No Description Qty AP1 01 25 1 1 06 1 16 Spring Pin 6 16 1 qus AP1 02 1 bius AP1 5 1 Caps Bote 2 1 6 1 Handle 1 TS 1482051 Bolt Hex M6x25 4
11. ty notices used in this manual ACAUTION This means that if precautions are not heeded it may result in minor injury and or possible machine damage AWARNING This means that if precautions are not heeded it may result in serious injury or possibly even death Introduction The arbor press is designed for riveting swaging bending punching and flattening The arbor press can be used to press on or remove close fitting bearings and bushings It is suited for the production environment as well as machine shops automobile repair shops and home workshops The anvil has four slots that are available for a variety of pressing operations Specifications SlOCK Hct ae 333605 333610 333620 333630 333650 APO M AP1 M AP2 M AP3 M AP5 M 25 ISON es 2 5Ton Dimensions length tede Td 18 1 8 26 1 8 Width iet 9 1 2 ted 12 3 4 Height itt tete tern 8 3 4 T751 8 201 2 ties 34 5 8 Max Working Height 4 3 4 STAR Speer 12 172 18 1 6 eite eret itid 6 5b B ssepe Bees 11 3 8 10 3 4
12. vil 1 Spring Pin 6x25 1 1 2 Handle 1 Bolt Hex 8 30 4 Washer M8 4 Bolt Hex M8x30 2 Bolt Hex M8x30 2 Nut Hex MB 4 Plate enu 1 SHSS 8 8 1 Pinion Retainer 1 Bolt Hex M8x20 1 Pinion 1 Kio Datei rete 1 Lock Washer M8 4 Model AP5 M 5 ton Arbor Press Index Part No TS 2361101 AP5 19 Description Qty 1 1 Spring Pin 6 24 1 Blame 1 Capt onm nee 2 Handle 1 Bolt Hex M10x40 4 Washer M10 4 Bolt Hex M10x40 2 Bolt Hex M10x50 2 Nut Hex M10 4 Plate 1 SHSS M8x12 1 Pinion Retainer 1 Pinion 1 Lock Washer M10 4 Exploded View WALTER MEIER Manufacturing Inc 427 New Sanford Road LaVergne Tennessee 37086 Ph 800 274 6848 www waltermeier com
Download Pdf Manuals
Related Search