Home

JET 414610 Use and Care Manual

image

Contents

1. 90 kg 198 4 Ib 130 kg 286 6 Ib 90 kg 198 4 lb 130 kg 286 6 Ib subject to local and national electrical codes no load with dust collection grinding flat bar 50x15mm with dust collection The specifications in this manual were current at time of publication but because of our policy of continuous improvement Walter Meier reserves the right to change specifications at any time and without prior notice without incurring obligations 7 0 Set Up and Assembly 7 4 Floor Diagram 318 9 5mm x 4 TI kj asane 2semm 3 aane _ 87 amm Figure 2 7 2 Unpacking and cleanup Inspect contents of shipping container for shipping damage Report any damage to your distributor Remove all contents from carton and compare to the contents list in this manual Report any part shortages to your distributor Do not discard carton or packing material until belt grinder is assembled and running satisfactorily Exposed metal areas may have a rust protectant applied Remove this with a soft rag and WD 40 or kerosene Do not use gasoline paint thinner acetone etc as these will damage painted surfaces Contents of shipping container 1 Belt Grinder 1 Instructions and Parts Manual not shown 1 Warranty Card not shown 7 3 Electrical Connections AWARNING Electrical connections must be made by a qualified electrician in complian
2. Support Catch Thin Hex Nut Wing Handle Side Panel Hex Bolt fully threade lt Washer Drive Wheel Spark Trap Hex Bolt fully threade Knob Adjustable Handle Hex Screw Phillips Pan Head Machine Screw for 1PH Phillips Pan Head Machine Screw for 3PH Flat Washer for 1PH Flat Washer for 3PH Bracket for 1PH Phillips Pan Head Machine Screw for 1PH Start Switch for 1PH Start Switch for 3PH Stop Switch for 1PH Stop Switch for 3PH Emergency Switch for 1PH Emergency Switch for 3PH Pan Head Machine Screw Flat Washer Electric Box Cover for 1PH 2 BG379 84 618M1 0216 618M1 0216 TS 1550031 TS 1550031 S 75 85 TS 1533052 S 75 85 8 3 TS 2284082 TS 1550021 S 75 85 11 S 75 85 11 3 Electric Box Cover for 3PH S 75 85 12 1 Cable for 1PH S 75 85 13 Electric Box for 1PH 8 75 85 13 3 Electric Box for 3PH S 75 85 14 Cable EERE PN ELE EEE E E ea Se a E E ene A N E E A TS 153204 Phillips Pan Hea 14 Index No Part No Description Size aty 85 16 S 75 85 16 S 75 85 16 3 Grounding Copper for 1PH Grounding Copper for 3PH A C Contactor for 1PH Thermal Relay for 1PH Transformer for 1PH Hex Nut for 1PH Hex Nut for 3PH Board for 1PH Board for 3PH Cover Plate for 1PH
3. to comply with all of these warnings may cause serious injury Replace the warning labels if they become obscured or removed This belt grinder is designed and intended for use by properly trained and experienced personnel only If you are not familiar with the proper and safe operation of a belt grinder do not use until proper training and knowledge have been obtained Do not use this machine for other than its intended use If used for other purposes Walter Meier Manufacturing Inc disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use Always wear approved safety glasses face shields while using this belt grinder Everyday eyeglasses only have impact resistant lenses they are not safety glasses Eye wear shall be impact resistant protective safety glasses with side shields which comply with ANSI Z87 1 specifications Before operating this belt grinder remove tie rings watches and other jewelry and roll sleeves up past the elbows Do not wear loose clothing and confine long hair Non slip footwear or anti skid floor strips are recommended Do not wear gloves or hold the work with a rag when grinding Wear ear protectors plugs or muffs during extended periods of operation Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or other reproductive harm
4. Cover Plate for 3PH Strain Relief Bracket for 3PH A C Contactor for 3PH Thermal Relay for 3PH Transformer for 3PH Holder for 1PH Holder for 3PH Breaker for 1PH lt Breaker for 3PH Cable for 3PH Cable for 3PH Cable for 1PH Cable for 1PH Cable for 1PH Cable for 1PH Cable for 1PH Cable for 1PH Cable for 1PH PE Cable for 1PH UV Cable for 1PH 12 AWG Cable for 3PH 0 332m Cable for 3PH 0 181m Cable for 3PH 0 415m Cable for 3PH 0 468m Cable for 3PH 0 412m Cable for 3PH 0 300m Cable for 3PH 0 200m PE Cable for 3PH 0 115m 16 AWG LN Cable to TC for 1PH 16 AWG LN Cable to KM1 for 1PH 16 AWGX3C LU L3 Cable to TC for 3PH UNM Cable to FR for 3PH L1 L2 L3 Cable to KM1 for 3PH Safety Guard Hinge S 75 85 19 TS 1540031 TS 1540031 S75 85 21 S75 85 29 3 S75 85 30 S75 85 30 3 S 75 85 31 S 75 85 32 0 8m 16 AWG x 4C 0 341M 18 AWG 0 196m 18 AWG 0 433m 18 AWG 0 479m 18 AWG 0 435m 18 AWG 0 3m 18 AWG 0 215m 18 AWG 0 115m 16 AWG 8 75 85 LIL3 8 75 85 UVW S 75 85 LIL2L3 TS 2285352 TS 1540031 S 75 94 S 75 95 BG379 94 BG379 95 BG379 96 BG379 97 BG379 WL JETLOGO 1 STRIPE 1 3 4 Phillips Pan Head Machine Screw Hex Nu Pad Large Washer Label Read Manua
5. make personal safety a priority If there are questions or comments please contact your local supplier or Walter Meier Walter Meier can also be reached at our web site www waltermeier com Retain this manual for future reference If the machine transfers ownership the manual should accompany it 5 0 Features Spark trap Eye shield Front work support Gontact wheel Top work support Belt guard Tracking adjustment knob Belt tension release lever 9 Industrial switch with overload protection 10 Angle lock handle x2 11 Drive wheel 12 Dust port 13 Side panel 14 Pedestal 15 Base ONOARORn Figure 1 16 Hinged guard plate 17 Tension adjustment nuts 18 Swing away safety guard 6 0 Specifications Model Number BG 379 1 BG 379 3 Stock Number 414610 414615 Materials Pedestal and Base teel steel Belt housing teel steel Abrasive belt provided Zirconium closed coat 80G Zirconium closed coat 80G Drive wheel aluminum aluminum Contact wheel 8 durometer HRAGO 65 serrated durometer HRA6O 65 serrated Motor and Electricals Motor type totally enclosed fan cooled induction capacitor start totally enclosed fan cooled induction Horsepower 4 HP 3 kW Phase single 3 Voltage 230V 230 460V prewired 230V Listed FLA full load amps 34 7A Starting amps 56 6A 15 2A 4004F 250VAC Running amps no load St
6. nearest you please call 1 800 274 6848 You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise If our inspection discloses a defect we will repair or replace the product or refund the purchase price at our option We will return the repaired product or replacement at our expense unless it is determined by us that there is no defect or that the defect resulted from causes not within the scope of our warranty in which case we will at your direction dispose of or retum the product In the event you choose to have the product returned you will be responsible for the shipping and handling costs of the return HOW STATE LAW APPLIES This warranty gives you specific legal rights you may also have other rights which vary from state to state LIMITATIONS ON THIS WARRANTY WALTER MEIER MANUFACTURING INC LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT EXCEPT AS STATED HEREIN ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL CONTINGENT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMIT
7. the cord rating is suitable for the amperage listed on the machine s motor plate An undersized cord will cause a drop in line voltage resulting in loss of power and overheating Use Table 1 as a general guide in choosing the correct size cord If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord Recommended Gauges AWG of Extension Cords Extension Cord Length 25 50 75 100 150 200 Amps feet feet feet feet feet feet lt 5 16 16 16 14 12 12 508 16 16 14 12 10 NR 8t012 14 14 12 10 NA NR 12t015 12 12 10 10 NA NR 15020 10 10 10 NR NA NR 21t030 10 NR NR NR NR NR based on limiting the line voltage drop to SV at 150 of the rated amperes NR Not Recommended Table 1 8 0 Adjustments Numbers in parentheses refer to Figure 1 8 1 Belt tracking 1 Open side panel 13 and spin drive wheel 11 by hand to check preliminary tracking 2 Use tracking knob 7 to correct until belt runs centered on wheels Clockwise knob rotation shifts belt toward the left counterclockwise toward the right as viewed from the contact wheel end 3 Close side panel 13 4 Connect machine to power and turn on to check final tracking Adjust as needed with knob J WARNING po not operate machine with side panel open 8 2 Belt change 1
8. ATION OR EXCLUSION MAY NOT APPLY TO YOU Walter Meier sells through distributors only The specifications in Walter Meier catalogs are given as general information and are not binding Members of Walter Meier reserve the right to effect at any time without prior notice those alterations to parts fittings and accessory equipment which they may deem necessary for any reason whatsoever JETebranded products are not sold in Canada by Walter Meier 2 0 Table of Contents Section 1 0 Warranty and Service 2 0 Table of Contents 3 0 Safety Warnings 4 0 About this manual 5 0 Features 6 0 Specifications 7 0 Set Up and Assembly 7 1 Floor Diagram 7 2 Unpacking and cleanup 7 3 Electrical Connections 7 4 Voltage Conversion 3PH oniy 8 0 Adjustments 8 1 Belt tracking 8 2 Belt change 8 3 Belt tension adjustment 9 0 Operation 9 1 Contact grindin 9 2 Surface grindin 10 0 Maintenance 11 0 Troubleshooting 12 0 Replacement Parts 12 1 1 BG 379 Belt Grinders Exploded View 12 1 2 BG 379 Belt Grinders Exploded View 12 1 3 BG 379 Belt Grinders Parts List 13 0 Electrical Connections single phase only 13 2 Electrical Connections 3 phase only OOOOOOOODEPEOOIDURON 3 0 Safety Warnings t Read and understand the entire owner s manual before attempting assembly or operation Read and understand the warnings posted on the machine and in this manual Failure
9. Disconnect machine from power 2 Allow belt to completely stop then remove spark trap 1 3 Open side cover and slacken belt by pushing tension release lever 8 downward counterclockwise 4 Install new belt according to direction arrows printed on belt 5 Move tension release lever 8 upward clockwise to tighten belt 6 Close side cover and reinstall spark trap 1 8 3 Belt tension adjustment Belt tension has been adjusted by the manufacturer If future adjustment is needed distance between the wheels can be changed using the two hex nuts 17 9 0 Operation 9 1 Contact grinding The operator faces the contact wheel 4 and holds the work piece with both hands Note Keep hands away from contact area which will grow warm during operation The work piece is pushed against belt and rested upon front work support 3 if needed 9 2 Surface grinding The operator faces the open belt guard 6 during surface grinding The work piece is held with both hands and pushed hard against the top work support 5 10 0 Maintenance AWARNING Before doing maintenance on the machine disconnect it from the electrical supply by pulling out the plug or switching off the main switch Failure to comply may cause serious injury Ball bearings have been packed with grease and sealed and require no further lubrication Frequent cleaning is mandatory to ensure best operation and extended life of the belt
10. Some examples of these chemicals are e Lead from lead based paint e Crystalline silica from bricks cement and other masonry products e Arsenic and chromium from chemically treated lumber 10 1 12 13 14 15 16 17 18 19 20 21 22 Your risk of exposure varies depending on how often you do this type of work TO reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as face or dust masks that are specifically designed to filter out microscopic particles Do not operate this machine while tired or under the influence of drugs alcohol or any medication Make certain switch is in OFF position before connecting machine to power supply Make certain machine is properly grounded Make al machine adjustments or maintenance with machine unplugged from power source Remove adjusting keys and wrenches Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on Keep safety guards in place at all times when machine is in use If removed for maintenance purposes use extreme caution and replace the guards immediately after maintenance is complete The belt grinder should be secured to the floor before using Check damaged parts Before further use of the machine a guard or other part that is damaged should be carefully checked to determine that it will operate pro
11. This pdf document is bookmarked JET Operating Instructions and Parts Manual 2 Wheel Belt Grinder 3 x 79 Model BG 379 WALTER MEIER Manufacturing Inc 427 New Sanford Road LaVergne Tennessee 37086 Part No M 414610 Ph 800 274 6848 Revision B 07 2012 www waltermeier com Copyright 2012 Walter Meier Manufacturing Inc 1 0 Warranty and Service Walter Meier Manufacturing Inc warrants every product it sells If one of our tools needs service or repair one of our Authorized Service Centers located throughout the United States can give you guick service In most cases any of these Walter Meier Authorized Service Centers can authorize warranty repair assist you in obtaining parts or perform routine maintenance and major repair on your JET tools For the name of an Authorized Service Center in your area call 1 800 274 6848 MORE INFORMATION Walter Meier is consistently adding new products to the line For complete up to date product information check with your local Walter Meier distributor or visit waltermeier com WARRANTY JET products carry a limited warranty which varies in duration based upon the product MW Metalworking WW Woodworking 291 1 E 21 21 Bl AEGI s lu HasEeue Paiet Tacks Seas LI Tables WW Dil Presses Fastening Toos ie giras Meuiiomng loging Equip Soewlads WW Dust Ooleciors Mechanics Hand Toots Mais Sergo Jaks Troleys Goaed WW Dust Fiers Sting Tels Machine Accessories Con
12. art capacitor Run capacitor Cycle i Motor speed Power transfer Power cable length 3440 RPM direct drive 83 om 6 ft 1 3360 RPM direct drive Power plug included me NO Controls industrial push button 24V 30A industrial push button 24V 30A Recommended circuit and breaker tuse 50A 30A 15A Noise emission Without load 85 db at 93mm 3 66 distance With load 88 db at 93mm 3 66 distance 5 db at 93mm 3 66 distance 38 db at 93mm 3 66 distance imensions and Capacities Abrasive belt size LxW Flat grinding surface Working height variable Belt speed 2000 x 75 mm 79 x 3 530 mm 21 780 1150 mm 30 3 4 45 1 4 40 m s 131 2 fps Contact wheel size Dia x W 200 x 75 mm 8 x 3 Drive wheel size Dia x W 225 x 75 mm 9 x 3 Shipping carton LxWxH 110 x 70 x 120cm 43 1 4 x27 1 2 x47 1 4 Machine size LxWxH 103 x 63 x 105cm 40 5 x25 x41 2 Base footprint LxW 17 x 21 43x53cm 2000 x 75 mm 79 x 3 530 mm 21 780 1150 mm 30 3 4 45 1 4 40 m s 131 2 fps 200 x 75 mm 8 x 3 225 x 75 mm 9 x 3 110 x 70 x 120cm 43 1 4 x27 1 2 x47 1 4 103 x 63 x 105cm 40 5 x25 x41 2 17 x 21 43x53cm Dust Extraction Dust port outside diameter Dust collection minimum capacity required 3 76 2mm 3 76 2mm 8 450 cfm 12 74cmm 450 cfm 12 74cmm
13. ce with all relevant codes This machine must be properly grounded to help prevent electrical shock and possible fatal injury The belt grinder is equipped with a single phase 230 volt only motor or a 3 phase 230 460V prewired 230V motor A plug is not included You may either install a ULICSA listed plug suitable for the specified voltage or hard wire the machine directly to a service panel If the machine is to be hard wired to a panel make sure a disconnect is available for the operator During hard wiring of the machine make sure the fuses have been removed or the breakers have been tripped in the circuit to which the machine will be connected Place a warning placard on the fuse holder or circuit breaker to prevent it being turned on while the machine is being wired Grounding Instructions This machine must be grounded In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock Improper connection of the equipment grounding conductor can result in a risk of electric shock The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to a live terminal Check with a qualified electrician or service personnel if the grounding instru
14. ctions are not completely understood or if in doubt as to whether the tool is properly grounded Repair or replace a damaged or worn cord immediately Make sure the voltage of your power supply matches the specifications on the motor plate of the belt grinder It is recommended that the single phase belt grinder be connected to a dedicated minimum 50 amp circuit with a 50 amp circuit breaker or time delay fuse the three phase belt grinder at 230 volt operation be connected to a dedicated minimum 30 amp circuit with a 30 amp circuit breaker or time delay fuse and the three phase belt grinder at 460 volt operation be connected to a dedicated minimum 15 amp circuit with 15 amp circuit breaker or time delay fuse Local codes take precedence over recom mendations 7 4 Voltage Conversion 3PH only To convert the 3 phase belt grinder from 230 to 460 volt operation 1 Switch the incoming power leads according to the diagram inside the motor junction box Similar diagrams are found in Section 13 of this manual In case of discrepancy the diagrams in the motor junction box will take precedence 2 Make sure connections to transformer are suitable for the new voltage 3 If a plug is being used install a UL CSA listed plug suitable for 460 volt operation Extension Cords The use of extension cords is discouraged try to position machines within reach of the power source If an extension cord becomes necessary make sure
15. grinder If graphite layer becomes damaged replace it Use a brush to remove swarf from the wheels and interior Check belt periodically for cuts frays or worn areas Replace belt when these symptoms are found Empty spark trap frequently It power cord is worn cut or damaged in any way have it replaced immediately 11 0 Troubleshooting Trouble Probable Cause Remedy No incoming power Check all connections Fuse blown or circuit breaker tripped Replace fuse or reset circuit breaker Grinder will not start Cord damaged Replace cord Starting capacitor malfunction single phase model Replace starting capacitor Improper belt splice Check belt for irregular seam or shape Excessive or insufficient belt tension Set tension so belt is just taut Check durometer on contact wheel Worn contact surfaces Replace worn wheel Poor belt tracking Check alignment of drive and contact Misaligned wheels wheel Adjust using tracking knob Check for slight crown approx 1 16 Lack of crown on drive wheel Replace drive wheel if crown is not present Slack belt Insufficient belt tension Set tension so belt is just taut Excessive belt tension Set tension so belt is just taut Premature wear of Grinding on one area of belt Use eire ball work alal contact wheel Le d Excess deposits on belt debris in Clean or replace belt Periodically clean machine interior of gri
16. l not shown Label Alert Symbol not shown Label Eye Protection not shown Label Hearing Protection not shown Warming Label not shown Jet Logo Plate not shown JET Stripe not shown 2 x 4 1 4 2 3 4 x8 1 3 4 w He RE NOR moin Dan So neue Lee ne cu eo nie CL MLD eg ee de Ds t 15 13 0 Electrical Connections single phase only 1PH re t TC 1 leg 3 t A n TAL sai KM s j KML serf FR EEE i oss f n dl fv KMI M 13 2 Electrical Connections 3 phase only PE 3PH 142 U3 TC 1 Ole t l I EE 5 TAI AA 3 sBi 3 2 4 sB2 H NAA kui 3 SRE L FR BEG FR 3 Mi 2 o 4 d d KMI This page intentionally left blank This page intentionally left blank JET WALTER MEIER Manufacturing Inc 427 New Sanford Road LaVergne Tennessee 37086 Phone 800 274 6848 www waltermeier com
17. l Bearing Stator for 1PH Stator for 3PH Motor Canister Upper Junction Box Lower Junction Box Phillips Pan Head Machine Screw S 75 14 15 1 Rotor for 1PH S 75 14 15 3 Rotor for 3PH Washer Cove Hex Bolt fully threaded Centrifugal Switch for 1PH Start Capacitor for 1PH Run Capacitor for 1PH Thin Plain Washer Belt Tension Release Base Socket Head Cap Screw Belt Tension Release Lever Sleeve Shaft Belt Guard Locking Handle Graphite Layer Hex Nut Socket Head Flat Screw Top Work Support Top Work Support Plate Lock Handle Eye Protection Base Philips Pan Head Machine Screw Socket Head Cap Screw Philips Pan Head Machine Screw Eye Protection Hinge 400pF 250VAC SOHF 450VAC 520x75mm ENB Oe Be OMe te nunnu nunnu A nn N Sw Oa WU NNNARROR NE 222 W RD DO RN RE 13 Index No Part No Description Size aty 37 S 75 1029 TS 1540021 Eye Protection Cover Hex Nu Block with Thread Contact Wheel Work Support Socket Head Flat Screw Stop Ring Ball Bearing Shaft Spacer Motor Support Nylon Lock Hex Nut Butteriiy Spring Screw Ba Base Socket Head Countersunk Screw lt Shaft Spring Pii Eccentric wheel Hex Bolt fully threade Spring Elasticity pi Retaining Ring Draw Bar Butterfly Spring
18. nder Allow belt to do the cutting Excessive Excessive grinding pressure pressure dulls belt and removes its grit Short belt life Use entire belt work surface whenever Grinding on one area of belt possible Table 2 12 0 Replacement Parts Replacement parts are listed on the following pages To order parts or reach our service department call 1 800 274 6848 Monday through Friday see our website for business hours www waltermeier com Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately 10 12 1 1 BG 379 Belt Grinders Exploded View 12 1 2 BG 379 Belt Grinders Exploded View 12 1 3 BG 379 Belt Grinders Parts List Index No Part No Description Size Qty Stand Nylon Lock Hex Nut TS 2360121 Flat Washer 8 75B 006 Inside Tube S 75B 004 Stand TS 154007 E TS 1550071 Flat Washer BG379 08 Internal Serrated Washer BG379 09 Socket Head Flat Screw TS 150202 Socket Head Cap Screw BG379 11 External Serrated Washer Socket Head Flat Screw Body Motor for 1PH 4HP 1PH 230V lt Motor for 3PH 4HP 3PH 230 460 Retaining Ring 25mm lt Motor Fan Cover for 1PH Motor Fan Cover for 3PH Socket Head Cap Screw Motor Fan for 1PH Motor Fan for 3PH Hex Cap Screw Flat Washer Lock Washer Housing Cover lt Bal
19. perly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced Provide for adequate space surrounding work area and non glare overhead lighting Keep the floor around the machine clean and free of scrap material oil and grease Keep visitors a safe distance from the work area Keep children away Make your workshop child proof with padlocks master switches or by removing starter keys Give your work undivided attention Looking around carrying on a conversation and horse play are careless acts that can result in serious injury 23 Maintain a balanced stance at all times so 29 Never leave the machine running that you do not fall or lean against moving unattended Turn power off and do not leave parts Do not overreach or use excessive machine until it comes to a complete stop Hotes 10 Peron any machine operation 30 Remove loose items and unnecessary work 24 Use the right tool at the correct speed and pieces from the area before starting the feed rate Do not force a tool or attachment machine to do a job for which it was not designed The right tool will do the job better and more 31 Do not grind magnesium as it may create a safely fire hazard 25 Use recommended accessories improper acce
20. ssories may be hazardous 26 Maintain tools with care Keep cutting tools Familiarize yourself with the following safety sharp and clean for the best and safest notices used in this manual performance Follow instructions for lubricating and changing accessories J CAUTION This means that if precautions 27 Turn off machine and disconnect from power are not heeded it may result in minor injury before cleaning Use a brush or compressed and or possible machine damage air to remove chips or debris do not use jour hands you JAWARNING rhis means that if precautions 28 Do not stand on the machine Serious injury are not heeded it may result in serious or even could occur if the machine tips over fatal injury 4 0 About this manual This manual is provided by Walter Meier Manufacturing Inc covering the safe operation and maintenance procedures for a JET Model BG 379 Belt Grinder This manual contains instructions on installation safety precautions general operating procedures maintenance instructions and parts breakdown Your machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this document This manual is not intended to be an exhaustive guide to belt grinder operational methods stock choice abrasive selection etc Additional knowledge can be obtained from experienced users or trade journals Whatever accepted methods are used always
21. tacter Motie Bases A Tol n s x M rg Machines Slackers Tolgstin WW Dust ings See Equipment ArTool iahi MW Bandsaws Surface Grinders Winches Manuel WW Jones Specialy hems n us MW Dril Presses Tir NW Aitan WW Lathes VseAccesso es Lubrication MW Feb Trleye Ae Ww Bandsams WWPanes NW Shapers Ecument Troleye Bcc MU Bulls WW Sanders WN Tablesans iat Mela TTT ison Visos Mehe ns Vises no recsion Clamps WHAT IS COVERED This warranty covers any defects in workmanship or materials subject to the exceptions stated below Cutting tools abrasives and other consumables are excluded from warranty coverage WHO IS COVERED This warranty covers only the initial purchaser of the product WHAT IS THE PERIOD OF COVERAGE The general JET warranty lasts for the time period specified in the product literature of each product WHAT IS NOT COVERED Five Year Warranties do not cover woodworking WW products used for commercial industrial or educational purposes Woodworking products with Five Year Warranties that are used for commercial industrial or education purposes revert to a One Year Warranty This warranty does not cover defects due directly or indirectly to misuse abuse negligence or accidents normal wear and tear improper repair or alterations or lack of maintenance HOW TO GET SERVICE The product or part must be returned for examination postage prepaid to a location designated by us For the name of the location

Download Pdf Manuals

image

Related Search

Related Contents

Hoshizaki FS-1001MLH-C User's Manual  AC1100 - Puericare.com  SFR200 assembly manual  Video Projector  SPJPM 46 P Artikel-Nr.: 3401038    Phyto Anti-tiques et Anti-puces  Samsung SH-W162L User Manual  Life Fitness Club Machine User's Manual  AMX AVB-TX-CATPRO-HD15-5T  

Copyright © All rights reserved.
Failed to retrieve file