General International 75-160 M1 Use and Care Manual
Contents
1. ADJUSTING AND USING THE CHUCK GUARD Loosen the wing nuts Q on both sides of the chuck guard and slide the chuck guard extension down along the two slots to the desired height Tighten the wing nuts to lock the chuck guard exten sion in place Note To facilitate drill bit installation removal flip the spring loaded chuck guard up as shown in o to keep it out of the way TO PREVENT THE RISK OF SERIOUS INJURIES ALWAYS COVER THE CHUCK AND DRILL BIT WITH THE CHUCK GUARD WHEN USING THE DRILL PRESS INSTALLING THE CHUCK 1 Slide the arbor into the quill assembly flat end goes in first 2 Slide the chuck onto the tapered end of the arbor and using the feed handle lower the quill assembly against the table to secure the chuck i To avoid damaging the chuck place a piece of wood on the table an Arbor r NJ REMOVING THE CHUCK AND ARBOR gt SAR 1 Turn OFF and disconnect the drill from the power source 2 Using feed handle lower the quill assembly 3 Insert tool into and all the way through the quill assembly Note It may be necessary to rotate the quill in order to be able to get the fool all the way through 4 While holding onto the chuck to prevent damage raise the quill assembly The arbor and chuck should fall out ADJUSTMENTS AND CONTROLS POWER ON Make sure the switch is in the OFF position and plug the power cord into a matching outlet Make sure the pulley guard is closed2. BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I D NAMEPLATE A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE IF IN DOUBT CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE THIS TOOL IS FOR INDOOR USE ONLY DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS GROUNDING INSTRUCTIONS In the event of an electrical malfunction or short circuit grounding reduces the risk of electric shock The motor of this machine is wired for 110V single phase operation and is equipped with a 3 conductor cord and a 3 prong grounding plug O to fit a grounded type recep tacle Do not remove the 3rd prong grounding pin to make it fit into an old 2 hole wall socket or extension cord If an adaptor plug is used OQ it must be attached to the metal screw of the receptacle Note The use of an adaptor plug is illegal in some areas Check your local codes If you have any doubts or if the supplied plug does not correspond to your elec trical outlet consult a qualified eletrician before pro ceeding CIRCUIT CAPACITY Make sure that the wires in your circuit are capable of handling the amperage draw from your machine as well as any other machines that could be operating on the same circuit If you are unsure consult a qualified electrician If the circu
3. LIGHT SWITCH ON OFF SWITCH SCREW ELECTRICAL CORD MOTOR CORD QTY PARTS LIST 75 150 PART NO DESCRIPTION QTY 75150 41 SNAP RING 1 75150 42 DRIVER INSERT 1 75150 43 BEARING 1 75150 44 SNAP RING 1 75150 45 BEARING 1 75150 46 QUILL GASKET 1 75150 47 QUILL 1 75150 48 BEARING 1 75150 49 SUPPORT CLAMP SEAT DEPTH STOP 1 75150 49 1 NUT 1 75150 50 SCREW 1 75150 51 SPINDLE 1 75150 52 DRIFT KEY 1 75150 53 ARBOR 1 75150 54 CHUCK 1 75150 55 KEY 1 75150 56 BOLT 2 75150 57 MOTOR 1 75150 58 SCREW 2 75150 59 CAPACITOR COVER 1 75150 60 CAPACITOR 1 75150 61 PULLEY GUARD 1 75150 62 MOTOR PULLEY 1 75150 63 SET SCREW 1 75150 64 SNAP RING 1 75150 65 SNAP RING 1 75150 66 BEARING 1 75150 67 MIDDLE PULLEY 1 75150 68 V BELT 1 75150 69 V BELT 1 75150 70 KNOB SEE ITEM 75200 03 1 75150 71 SCREW 1 75150 72 SHAFT ASSEMBLY 1 75150 73 NUT 1 75150 74 SPINDLE PULLEY 1 75150 75 SCREW 1 75150 76 CORD CLAMP 1 75150 77 ELECTRICAL CORD LAMP 1 75150 78 SCREW 1 75150 79 SCREW 1 75150 80 KEY HOLDER 1 75150 8 1 WASHER 1 75150 82 NUT 1 75150 83 SCREW 1 75150 84 DEPTH STOP ROD 1 75150 85 NUT 2 75150 86 DEPTH STOP SUPPORT 1 75150 87 CHUCK GUARD ITEM 70 115A 1 75150 88 COLUMN PLATE 1 75150 89 WASHER 1 75150 90 SPRING 1 75150 91 WASHER 1 1 75150 92 CAP SCREW DIAGRAM 75 150 Km AT NY w 38Ne PART NO 75160 01 75160 02 75160 03 75160 04 75160 05 75160 06 75160 07 75160
4. Check that the chuck or keyless chuck is installed properly When turning the machine ON be aware that the shaft will rotate freely When the drill press is running check to see if it runs without vibration or shaking Make sure the table bracket moves up and down smoothly Make sure the spindle shaft turns smoothly S ND a E ON Unlock the cover press the green start button for starting machine Press the red button to stop machine OO a EH RITTER WORK LIGHT SWITCH POWER ON POWER OFF ADJUSTING TABLE HEIGHT 1 Loosen the column lock handle 1 2 Turn the crank handle 2 until the table is at the desired height 3 Retighten the column lock handle 1 before starting TABLE TILT ADJUSTMENT 1 Loosen the pivot bolt 4 and set screw 5 2 Tilt the table to the desired angle 3 Retighten the pivot bolt 4 and set screw 5 DRILLING TABLE SWING ADJUSTMENT 1 Loosen column lock handle 1 2 Swing the table arm bracket and the table to the desired position Retighten column lock handle 1 When working with taller work pieces swing the table 180 out of the way and use the base as a table DEPTH STOP ADJUSTMENT 1 Set the bottom edge of nut 1 even with the desired depth setting 2 Tighten nut 2 against nut 1 to secure it in position Depth stop is now set and will provide repetitive holes of equal depth Always use hold downs or clamps to secure the workp
5. 07 1 75160 08 75160 09 75160 10 75160 11 75160 12 75160 13 75160 14 75160 15 75160 16 75160 17 75160 18N 75160 19 75160 20 75160 21 75160 22N 75160 23 75160 24N 75160 25 75160 26 75160 26 1 75160 26 2 75160 27 75160 28 75160 28 1 75160 29 75160 30 75160 31 75160 32 1 75160 33 75160 34 75160 35N 75160 36 75160 37 75160 38N 75160 39 75160 40 75160 40 1 75160 41 75160 42 PARTS LIST 75 160 DESCRIPTION BASE WASHER BOLT BASE FLANGE SCREW CRANK SLEEVE HANDLE TABLE BRACKET TILT SCALE GEAR SHAFT HELICAL GEAR ELEVATING WORM CLAMP BOLT TABLE ARM BRACKET SET SCREW CLAMP BOLT WASHER BOLT TABLE RACK COLUMN 73 X 1160 SCREW RACK COLLAR FEED HANDLE HANDLE KNOB PINION SHAFT SLEEVE HEAD SET SCREW RUBBER BUSHING SET SCREW BELT TENSION ADJUSTMENT ROD SPRING SCREW SCREW LAMP HOLDER NUT NUT SPRING amp CAP SWITCH BOX SCREW LIGHT SWTICH ON OFF SWITCH SCREW ELECTRICAL CORD MOTOR CORD SNAP RING DRIVER INSERT QTY PARTS LIST 75 160 PART NO DESCRIPTION QTY 75160 43 BEARING 1 75160 44 SNAP RING 1 75160 45 BEARING 1 75160 46 QUILL GASKET 1 75160 47 QUILL 1 75160 48 BEARING 1 75160 49 SUPPORT CLAMP SEAT DEPTH STOP 1 75160 49 1 NUT 1 75160 50 SCREW 1 75160 51 SPINDLE 1 75160 52 DRIFT KEY 1 75160 53 ARBOR 1 75160 54 CHUCK 1 75160 55 KEY 1 75160 56 BOLT 2 75160 57 MOTOR 1 75160 58 SCREW 2 75160 59 CAPACITOR COVER 1 75160 60 CAPACITOR 1 75160 61 PULLEY GUARD
6. Heavy duty carbon steel Heat treated and precision sharp ened for quick accurate and effortless cuts Includes 6 bits sizes 1 4 5 16 3 8 1 2 5 8 3 4 with 3 8 shank in a conve nient carrying case ABRASIVE SLEEVES 70 030 10 piece replacement abrasive sleeve set for 70 025 Includes 5 one of each size 80 amp 120 grit sanding sleeves DRILL PRESS TOOL TRAY 70 125 Can be installed on most drill press columns Made from durable plastic with a metal swivel rod 12 X 24 305 X 610 MM DRILL PRESS CHUCK Prevents unintentional user con UNIVERSAL DRILL PRESS TABLE GUARD 70 155 tact with the chuck and bit dur 70 135 ing operations 17 X 32 432 X 813 MM gt e Contains wood chips shavings UNIVERSAL DRILL PRESS TABLE 470 140 Adas versatility to your drill press and repeatable accuracy to your work Includes 3 tall 2 pc Full length fence with t slot and stop 2 1 2 dust port connection parallel t slots in table and 2 workpiece holdowns Mounts to all drill tables with mounting holes 9 VISE CLAMP 70 130 Adjustable lock in clamping pressure and 360 degree rota tion a must for all safety con scious woodworkers Includes 1 2 t bolts to mount to any drill table with 9 16 or wider mounting holes or other debris for safer drilling Designed to meet the most strin gent industrial and educa tional safety req
7. changes on previously delivered units Reasonable care is taken at the factory to ensure that the specifications and information in this manual corres ponds with that of the unit with which it was supplied However special orders and after factory modifica tions may render some or all information in this manual inapplicable to your machine Further as several gene rations of this model of drill and several versions of this manual may be in circulation if you own an earlier or later version of this unit this manual may not depict your tool exactly If you have any doubts or questions contact your retailer or our support line with the model number of your unit for clarification GENERAL amp GENERAL INTERNATIONAL WARRANTY All component parts of General General International and Excalibur by General International products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly Limited Lifetime Warranty Because of our commitment to quality and customer satisfaction General and General International agree to repair or replace any part or component which upon examinaiion proves to be defective in either workmanship or material to the original purchaser for the life of the tool However the Limited Lifetime Warranty does not cover any product used for pro fessionnal or commercial production purposes nor for industrial or educational applications Suc
8. model and serial number of the unit if applicable and including an expla nation of the complaint or presumed defect in material or workmanship CONDITIONS AND EXCEPTIONS This coverage is extended to the original purchaser only Prior warranty registration is not required but documented proof of purchase i e a copy of original sales invoice or receipt showing the date and location of the purchase as well as the purchase price paid must be provided at the time of claim Warranty does not include failures breakage or defects deemed after inspection by General or General International to have been directly or indirectly caused by or resulting from improper use or lack of or improper maintenance misuse or abuse negligence accidents damage in handling or transport or normal wear and tear of any generally considered con sumable parts or components Repairs made without the written consent of General International will void all warranty RULES FOR SAFE OPERATION To help ensure safe operation please take a moment to learn the machine s applications and limitations as well as poten tial hazards General International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment Do not operate the drill press when tired distracted or under the effects of drugs alcohol or any medication that impairs reflexes or alertness The working area should be wel
9. 0 FT MIN 24 M MIN 100 FT MIN 30 M MIN 200 FT MIN 60 M MIN DIAMETER REVOLUTIONS PER MINUTE 1910 2445 RPM 2865 3665 RPM 3820 4890 RPM 4775 6110 RPM 9550 12225 RPM MAINTENANCE Keep the unit clean and free of dust and debris Painted surfaces can be wiped with a damp rag e Periodically lubricate oil or grease all sliding or moving parts including the column and table tilt mechanisms brackets worm gears and the quill e Bearings in the quill and the V belt pulley are sealed permanently lubricated and maintenance free e Lightly oil the slide bars every 2 months e f cranking becomes difficult grease the column bracket IMPORTANT USE ONLY GENERAL INTERNATIONAL OR AUTHORIZED REPLACEMENT PARTS AND ACCESSORIES REGOMMENDED OPTIONAL ACCESSORIES We offer a large variety of products to help you increase convenience productivity accuracy and safety when using your drill press Here s a small sampling of optional accessories available from your local General International dealer For more information about our products please visit our website at www general ca 25 PIECE RUBBER DRUM SANDING SET 175 025 Turn your drill press into a mini drum sander Ideal for small sanding jobs on curved or odd shaped pieces Kit includes 5 different sized drums 1 2 3 4 1 1 1 2 g 2 plus 2 sets of 80 grit and 2 sets of 120 grit sanding sleeves for each 9 AUGER DRILL BIT SET 70 105
10. 1 75160 62 MOTOR PULLEY 1 75160 63 SET SCREW 1 75160 64 SNAP RING 1 75160 65 SNAP RING 1 75160 66 BEARING 1 75160 67 MIDDLE PULLEY 1 75160 68 V BELI 1 75160 69 V BELT 1 75160 70 KNOB SEE ITEM 75200 03 1 75160 71 SCREW 1 75160 72 SHAFT ASSEMBLY 1 75160 73 NUT 1 75160 74 SPINDLE PULLEY 1 75160 75 SCREW 1 75160 76 CORD CLAMP 1 75160 77 ELECTRICAL CORD LAMP 1 75160 78 SCREW 1 75160 79 SCREW 1 75160 80 KEY HOLDER 1 75160 81 WASHER 1 75160 82 NUT 1 75160 83 SET SCREW 1 75160 84 DEPTH STOP ROD 1 75160 85 NUT 2 75160 86 DEPTH STOP SUPPORT 1 75160 87 CHUCK GUARD ITEM 70 115A 1 75160 88 COLUMN PLATE 1 75160 89 WASHER 1 75160 90 SPRING 1 75160 91 WASHER 1 1 75160 92 CAP SCREW DIAGRAM 75 160 NOTES 17 75 150 amp 75 160 8360 Champ d Eau Montreal Quebec Canada HIP 1Y3 Tel 514 326 1161 Fax 514 326 5565 Parts amp Service Fax 514 326 5555 Order Desk orderdesk general ca www general ca IMPORTANT When ordering replacement parts always give the model number serial number of the machine and part number Also a brief description of each item and quantity desired
11. 6 5555 www general ca THANK YOU for choosing this General International model 75 150 75 160 drill press This drill has been carefully tested and inspected before shipment and if properly used and maintained will provide you with years of reliable service To ensure optimum perfo rmance and trouble free operation and to get the most from your investment please take the time to read this manual before assembling installing and operating the unit The manual s purpose is to familiarize you with the safe operation basic function and features of this drill as well as the sef up maintenance and identification of its parts and components This manual is not intended as a substitute for formal woodworking instruction nor to offer the user instruction in the craft of woodworking If you are not sure about the safety of performing a certain operation or procedure do not proceed until you can confirm from knowledgeable and qualified sources that it is safe to do so Once you ve read through these instructions keep this manual handy for future reference Disclaimer The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing Because we are commit ted to making constant improvements General International reserves the right to make changes to components parts or features of this unit as deemed necessary without prior notice and without obligation to install any such
12. SETUP amp OPERATION MANUAL CENOWE 14 6 16 DRILL PRESSES Rotating 45 tilting crank operated work table with quick release clamp Large front mounted stop switch with lock out safety feature to prevent unwanted or unintentional start up Adjustable spindle tension return spring Built in lamp illuminates the drilling area Spindle is supported by high quality ball bearings Cast iron pulleys reduce vibration Industrial 1 2 HP motor Heavy duty positive depth stop for quick adjustment 5 8 drill chuck SWING 13 34 340 mm 475 150 16 406 mm 75 160 DRILLING CAPACITY 54 16 mm CHUCK SIZE 54 16 mm SPINDLE TRAVEL 3 14 80 mm SPINDLE DISTANCE TO TABLE 30 3 781 mm 75 150 30 546 770 mm 475 160 SPINDLE DISTANCE TO BASE 48 1219 mm 475 150 47 11 4 1212mm 475 160 TABLE SIZE 11 34 289 mm 75 150 10 1 268 mm 475 160 COLUMN DIAMETER 2 74 73 mm NUMBER OF SPEEDS 12 SPINDLE SPEEDS 280 3000 RPM SPINDLE TAPER MT 2 1 OVERALL HEIGHT 62 1575 MM BASE SIZE 7 L ISO MI 10 14 x 17 14 75 150 N 7 39 160 MI MOTOR 1 HP 110 8 A WEIGHT 121 LBS 55 kg 75 150 134 LBS 61 kg 75 160 VERSION 2 AUGUST 07 12 O Copyright GeneralO International 08 2012 GENERAL INTERNATIONAL 8360 Champ d Eau Montreal Quebec Canada HIP 1Y3 Telephone 514 326 1161 Fax 514 32
13. URE THE DRILL PRESS IS INSTALLED ON A FLAT SOLID AND STABLE SURFACE Place the base 1 on a flat surface and screw the column 8 to the base Remove the rack ring 9 from the column 8 Insert the rack 11 into the table bracket and position the 2 pieces onto the column at the same time The bottom lip of the rack is pressed bet ween the column and the flange The top lip of the rack is similarly secured with the replacement of the rack ring 9 Tighten the set screw in the rack ring Place the handle 10 on the worm gear and secure it with the hex head bolt Attach the head 2 to the column and tighten the head with the set screws 3 Secure the table onto the table arm Attach the 3 feed handles 4 5 amp 6 to the handle body 7 7 If desired install a max 60 watt light bulb not included for the worklight 12 Once assembled clean the protective coating from all surfaces where applicable using a rag dipped in kerosene mineral spirits or paint thinner Dispose of potentially flammable solvent soaked rags according to manufacturer s safety recommendations A putty knife held flat to avoid scratching the surface may also be used to scrape off the coating followed by clean up with solvent Avoid rubbing painted surfaces as many solvent based products will remove paint INSTALL THE CHUCK GUARD Fit the chuck guard onto the quill O and tighten the Phillips screw to secure the chuck guard in place 7
14. h cases are covered by our Standard 2 year Limited Warranty only The Limited Lifetime Warranty is also subject to the Conditions and Exceptions as listed below Standard 2 Year Limited Warranty All products not covered by our lifetime warranty including products used in commercial industrial and educational applications are warranted for a period of 2 years 24 months from the date of purchase General and General International agree to repair or replace any part or component which upon examination proves to be defective in either workmanship or material to the original purchaser during this 2 year warranty period subject to the conditions and exceptions as listed below To file a Claim To file a claim under our Standard 2 year Limited Warranty or under our Limited Lifetime Warranty all defective parts components or machinery must be returned freight or postage prepaid to General International or to a nearby distributor repair center or other location designated by General International For further details call our service department at 1 888 949 1161 or your local distributor for assistance when filing your claim Along with the return of the product being claimed for warranty a copy of the original proof of purchase and a letter of claim must be included a warranty claim form can also be used and can be obtained upon request from General International or an authorized distributor clearly stating the
15. iece The workpiece should never be held only by hand Take care to use clean sharp bits Damaged or broken bits could result in serious injury When drilling flat work place the worpiece on a wooden base and clamp it down against the table For working in wood machine spur bits are generally preferred Do not use hand bits which have a screw tip At drill press soeeds these bits rotate into the workpiece so rapidly that they lift the workpiece off the table and swirl it TABLE ROTATION ADJUSTMENT 1 Loosen the table lock handle 3 2 Rotate the table to the desired position 3 Retighten the table lock handle 3 CHANGING SPEEDS MAKE SURE THE DRILL PRESS HAS COME TO A COMPLETE STOP BEFORE CHANGING SPEEDS REFER TO THE SPINDLE SPEED SELECTION CHART LOCATED ON THE INSIDE OF THE SPINDLE COVER 1 Disconnect the drill press from the power source Loosen the slide bar bolt 1 located on the right side of the head Pull the motor 2 in towards the head to loosen the belts Relocates belts to the desired pulleys to select a new spindle speed Push the motor 2 back away from the head Retighten the slide bar bolt 1 and check the belt tension oa Ron THE FOLLOWING TABLE CAN BE USED AS A GUIDLINE FOR SELECTING SPEEDS BASED ON BIT SIZE amp BIT MATERIAL BIT SIZE BIT MATERIAL CAST STEEL TOOL STEEL CAST IRON MILD STEEL ALUM amp COPPER CUTTING SPEED 40 FT MIN 12 M MIN 60 FT MIN 18 M MIN 8
16. it breaker trips or the fuse blows regularly your machine may be operating on a circuit that is close to its amperage draw capacity However if an unusual amperage draw does not exist and a power failure still occurs contact a qualified technician or our service department EXTENSION CORDS Ifyou find it necessary to use an extension cord with your machine use only 3 wire extension cords that have 3 prong grounding plug and a matching 3 pole recepta cle that accepts the tool s plug Repair or replace a damaged extension cord or plug immediately Make sure the cord rating is suitable for the amperage listed on the motor I D plate An undersized cord will cause a drop in line voltage resulting in loss of power and overheating The accompanying chart shows the correct size extension cord to be used based on cord length and motor I D plate amp rating If in doubt use the next heavier gauge The smaller the number the heavier the gauge TABLE MINIMUM GAUGE FOR CORD TOTAL LENGTH OF CORD IN FEET AMPERE tovotrs 25 Feet SOFtET 100 FEET 150 FEET RATING 220 vours 50 EET 100 FEET 200 eT 300 FET ING CI NR Not Recommended 14 OR 16 DRILL PRESSES 75 150 75 160 ASSEMBLY INSTRUCTIONS Before proceeding with the assembly read the operating and maintenance instructions manual and familiarize yourself with correct assembly setup maintenance and safety procedures TO AVOID RISK OF SERIOUS INJURY MAKE S
17. l lit clean and free of debris Keep children and visitors at a safe distance when the drill press is in operation do not permit them to ope rate the drill press Childproof and tamper proof your shop and all machinery with locks master electrical switches and switch keys to prevent unauthorized or unsupervised use Stay alert Give your work your undivided attention Even a momentary distraction can lead to serious injury Fine particulate dust is a carcinogen that can be haz ardous to health Work in a well ventilated area and whenever possible use a dust collector and wear eye ear and respiratory protection devices Do not wear loose clothing gloves bracelets neck laces or other jewelry while the drill press is in opera tion Be sure that adjusting wrenches tools drinks and other clutter are removed from the machine and or the table surface before operating Keep hands well away from the drill bit and all moving parts Use a hold down or clamp to secure the stock and use a brush not hands to clear away chips and dust Be sure that the drill bit is securely installed in the chuck before operation Be sure the drill bit has gained full operating speed before beginning to drill Always use a clean properly sharpened bit Dirty or dull bits are unsafe and can lead to accidents Use suitable work piece support if the work piece does not have a flat surface Do not push or force the bit into
18. the stock The drill will perform better and more safely when working at the rate feed for which it was designed Avoid working from awkward or off balance positions Do not overreach and keep both feet on floor Keep guards in place and in working order If a guard must be removed for maintenance or cleaning be sure it is properly re attached before using the tool again Never leave the machine unattended while it is run ning or with the power on Use of parts and accessories NOT recommended by GENERAL INTERNATIONAL may result in equipment malfunction or risk of injury Never stand on machinery Serious injury could result if the tool is tipped over or if the drill bit is unintention ally contacted Always disconnect the tool from the power source before servicing or changing accessories such as bits or before performing any maintenance cleaning or if the machine will be left unattended Make sure that the switch is in the OFF position before plugging in the power cord Make sure the tool is properly grounded If equipped with a 3 prong plug it should be used with a three pole receptacle Never remove the third prong Do not use this drill press for other than its intended use If used for other purposes GENERAL INTERNA TIONAL disclaims any real implied warranty and holds itself harmless for any injury which may result from that use GX ELECTRICAL REQUIREMENTS A
19. uirements e Sturdy cast aluminum body and pact resistant windows e Spring loaded flip up design allows for quick drill bit changes without interference DRILL PRESS VISES 95 140 95 150 95 160 Hold down slots along both sides High tensile iron cast ing construction for maxi mum durability One piece cast iron axial sleeve and movable jaws Fast action Acme type screw threads 95 140 4 95 150 5 95160 6 PART NO 75150 01 75150 02 75150 03 75150 04 75150 05 75150 06 75150 07 75150 07 1 75150 08 75150 09 75150 10 75150 11 75150 12 75150 12 1 75150 13 75150 14 75150 15 75150 16 75150 17 75150 18N 75150 19 75150 20 75150 21 75150 22N 75150 23 75150 24N 75150 25 75150 26 75150 26 1 75150 26 2 75150 27 75150 28 75150 28 1 75150 29 75150 30 75150 31 75150 32 75150 32 1 75150 33 75150 34 75150 35N 75150 36 75150 37 75150 38N 75150 39 75150 40 75150 40 1 PARTS LIST 75 150 DESCRIPTION BASE WASHER BOLT BASE FLANGE SCREW CRANK SLEEVE HANDLE TABLE BRACKET TILT SCALE GEAR SHAFT HELICAL GEAR ELEVATING WORM CLAMP BOLT TABLE ARM BRACKET POINTER SET SCREW CLAMP BOLT WASHER BOLT TABLE RACK COLUMN 73 X 1160 SCREW RACK COLLAR FEED HANDLE HANDLE KNOB PINION SHAFT SLEEVE HEAD SET SCREW RUBBER BUSHING SET SCREW BELT TENSION ADJUSTMENT ROD SPRING SCREW SCREW LAMP FRAME LAMP HOLDER NUT NUT SPRING amp CAP SWITCH BOX SCREW
Download Pdf Manuals
Related Search