SPEEDWAY 51850 Instructions / Assembly
Contents
1. Please careuly read and save those instructions before atterotng fo assemble maintain install or operat this product Observ all safety information to protoct yourself and athera Failure to observe the instructione may result in property damage ander personal injury Please keep instructions for future reference Important Operating Instructions North 60 GALLON COMPRESSOR Model 51850 52332 CALIFORNIA PROPOSITION 65 Breathable Air Warning ASSEMBLY WARNING You can create dust This compressoripump is not INSTRUCTIONS when you cut sand drill or grind equipped and should not be materials such as wood paint used cas ia to supply Do not operate me metal concrete cement orother breathing qualty ai for any Compressor without libricant masonry This dust often Daea ata for homer r wih ow lubricant levels It Contains chemicals known to consumption the air Could cause damage to the auso cancer birth defects or compreseorpump will noed Compressor iher reproductive harm Wear to be ted wah suitable ns protective gear line safety snd alana 1 Chock the o ove Add WARNING This product or its equipment This additional eon A eee power cond may contain senspment In necessary gt supplied oil into oil tank until chemicals including lead properly filter and purify the Sete cg ciate known to the State of California SSO Ratione for Grado the oi level sight las Do Gelocte or other roproduc2. n and replace oil drain plug 6 Refil crankcase with SAE 20 or SAE 30 weight non detergent oil to the red dot on the ol level sight glass Be careful not to over the tank eoabachGnattoolscom 400 348 5004
3. tive breathing as described in not over fil penig erkni es Compressed Gas Association mene Catia soeciicetecG 2 instal oi fi plug before 7 1966 OSHA 29 CFR stating 4810 194 andlor Canadian Caumon aien Aaa 3 Close the tank valve on the Bonom ofthe air tark by FOR YOUR OWN SAFETY READ turing the vave dockise INSTRUCTION MANUAL SPECIFICATION 4 A shut off valve ideally 34 Berone orenavine THis Tank Sizo 60 galons J snou bested on he COMPRESSOR BPN 11 6 GAPE discharge port of the tank Failure to follow all instructions 102 G0 Eat Use Teflon tape on the Horsepower Running 3HP threads to ensure an airtight as listed below may result in electrical shock fire andor Max Pressure 135 PSI connection between the tank serious personal injury Thermal overload protection and the plumbing or hose coupler Do not over tighten the tings For warranty purchases pi se keep your dated proof of purchase Fie or attach to the manual for safekeeping Forcualoner sevice sal 1 090940 5004 or ana feedback natoot com ei 88051850 04712 5 Attach the supplied air fiter to the air intake port on the pump head 6 Attach the air hose and any desired accessories not included Use Teflon tape on the threads to ensure an airtight connection Do not over tighten the fitings Note Vibrationisolator pads are recommended prior to bolting to the floor Only mount the compressor
4. to a concrete floor or concrete pad OPERATING INSTRUCTIONS Start Up 41 Tum the ON OFF switch to the off position 2 Check the air compressor visually for any damage or obstruction 3 Close the drain valve 4 Plug the power cord into the proper receptacle if required 5 Turn the ON OFF switch to the ON position and the compressor should star and build air pressure in the tank to cut out pressure and then shut off automatically 6 Adjust the air regulator to a PSI setting that is recommended for the application at hand not included 7 The air compressor is ready for use Shut Down 1 Turn the ON OFF switch to the OFF position 2 Unplug the power cord from the receptacie 3 Set the outlet pressure to zero fn the regulator 4 Remove any air tools or 5 Open the drain valve allowing air to bleed from the tank After all of the air has bled from the tank close the drain valve to prevent debris buildup in the vave Water that remains in the tank during storage wil corrode and weaken the air tank which could cause the tank to rupture To avoid serous injury ensure the tank is drained property after each use or daily Check the tank safety valve and air fter before each use CHANGING THE OIL 1 Place oil drain pan below the oil drain plug 2 Remove dipstick to alow the air to enter the crankcase 3 Remove oil drain plug 4 Allow oil to drain completely 5 Clea
Download Pdf Manuals
Related Search