SPEEDWAY 51647 Use and Care Manual
Contents
1. ae Belt Guard L 4 troatherioipsiac Tank Pressure Gauge Pressure Switch Attach air howe at outlet of ragulator air Hose Pressure Gauge Figure 1 teedback nathools com m 300 32. Insert and tighten the handle screw Into the hole in the base plate and through the teedbackibnatitoots com 4 800 348 5004 handle Ensure the screw goes all the way through the handle Wheel Assembly 1 Insert the shoulder bolt through the wheel hub with the bolt head on the opposite side of the protruding section 2 For the 8 inch diameter wheels insert the shoulder bolt into the lowest hole of the tank axle iron and secure tightly with a locknut 3 For the 10 inch diameter wheels insert the shoulder bolt into the upper hole in the tank axle iron and tightly secure with the locknut 4 Repeat step 3 or 4 on the opposite side By whats When the unitis assembled the tank should slope slightly towards the drain valve to allow the tank to drain propery Breather Installation Remove the cap from the oil fil opening Install the breather Fig Oil Addition The oil capacity of this unit is approximately 8 5 ounces Synthetic oil is recommended Use 10W30 100 non detergent synthetic oil for best results Single viscosity IS0100 SAE 30 non detergent compressor oll can also be used DO NOT use petroleum based automotive oil with this unit It will cause carbon deposits which will require the unit to be serviced more frequently and reduce the life of the unit OPERATION Note This compressor must be filed with oil before startup CAUTION Do not attach air tools to th
3. drain water from the tank teedbackibnatitoots com NOTE Electric models are equipped with a pressure switch that automatically turns the motor OFF when the tank reaches a preset level After air is used from the tank and it drops to a preset low level the pressure switch will automatically turn the motor back on MAINTANANCE WARNING Disconnect the unit from the power source and tools and release all pressure from the tank before attempting to perform any maintenance or service to the unit Perform the following test to verify the operation of the safety valve weekly and follow the maintenance schedule below 1 Pull the ring on the safety valve and allow the ring to snap back into its normal position This valve automatically releases air if the tank pressure exceeds the preset maximum CAUTION A large amount of fast moving air will be released if the safety valve is pulled with air pressure in the tank WARNING Do not attempt to tamper with this valve It should be checked before each use If air leaks after the ring as been released or the valve is stuck and cannot be actuated by the ring the valve must be replaced DO NOT use the unit until the ring has been replaced 2 With the motor OFF and unplugged clean debris from the motor flywheel tank air lines and pump cooling fins Drive Belt Belts will stretch with normal use Properly adjusted a 5 pound pressure is applied to the bel
4. Pease carefully read and save these instructions before attempting to assemble maintain install or operate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage and or personai injury Please keep instructions for future reference important Operating Instructions ert ameron 20 GALLON BELT DRIVEN COMPRESSOR Model 51647 CALIFORNIA PROPOSITION 65 accidents which arise due to non SAFETY INSTRUCTIONS observance of these instructions and the safety information herein The air compressor should be operated on a dedicated 20 amp circuit If the circuit does not have 20 free amps available a larger circuit must be used Always use more air hose before utilizing extension cords Low voltage WARNING You can create dust when you cut sand drill or grind materials such as wood paint metal concrete coment or other SPECIFICATIONS masonry This dust often Motor 2 HP Dual Voltage contains chemicals known to 120V 240V Belt Driven cause cancer birth defects or other reproductive harm Wear Tank 20 Gallons could cause damage to the motor protective gear eel conte Gansage Is the ok WARNING This product or its Pump Castiron Ifthe air compressor is in power cord may contain operation all guards and covers chemicals including lead Max resale TEPA should be attached or installed known to the State of California correctly If an
5. e compressor until startup is completed and the unit checks OK 1 Check for proper oil level 2 Turn the regulator knob Clockwise to open air flow 3 Tum the pressure switch lever or knob to OFF position and plug in power cord S XS Knob ee E Figure 9 Lever Auto 4 Turn the pressure switch lever or knob to AUTO and run the unit for 30 minutes to break in the pump parts Fig 9 5 Turn the regulator knob fully counterclockwise The unit will build to maximum preset pressure and automatically shut off 6 Turn the regulator knob clockwise to cause air to bleed off The unit will restart at preset pressure 7 Turn the pressure switch lever or knob to OFF and unplug the power cord Slowly tum the regulator knob clockwise to allow the air pressure to be released DO NOT proceed to the next step until the tank pressure gauge reads zero 8 Attach an air hose not included and then add an air chuck or other tool not included to the open end of the hose Use teflon tape to eliminate air leaks when attaching tools or air hose Plug in the power cord Turn the pressure switch lever to AUTO position When the full pressure is reached turn the regulator knob clockwise until desired outlet pressure is achieved 9 After use turn the pressure switch lever or knob to OFF 10 Ifthe compressor is not used for an extended period of time bleed the air from the line and use the drain valve to
6. er condensation is not caused by compressor malfunction Be sure the compressors air output is greater than your tool s air consumption rate Air leaks from the tank body or tank welds Never Gril into weld or otherwise modify the alr tank or twill weaken The tank can rupture or explode Compressor cannot be repaired Discontinue use of the air compressor teedbackidnatitoots com Limited Manufacturer Warranty North American Tool NAT Industries makes every effort to ensure that this product meets high quality and durability standards NAT warrants to the original retail consumer a 1 year limited warranty from the date the product was purchased at retail and each product is free from defects in materials Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NAT shall in no event be liable for death injuries to persons or property or for incidental special or consequential damages arising from the use of our products To receive service under warranty the original manufacturer part must be retumed for examination by an authorized service center Shipping and handling charges may apply If a defect is found NAT wil either repair or replace the product at its discretion DO NOT RETURN TO STORE For Customer Service Email feedback natitools com or Call 1 800 348 5004 Discharge Tube sihe Wek Vave A tae Fit
7. pressure in the tank and the compressor is shut off Drain the tank then remove and clean or replace the check valve Air leaks between head and cylinder Be sure of proper torque on head bolts I Teak remains contact a service technician Air leak from safety valve Operate the safety valve manually by pulling on the ring if the valve continues to leak when in the closed position it should be replaced Pressure reading on the regulated pressure gauge drops when an accessory is used If there is an excessive amount of pressure drop when the accessory is used replace the regulator NOTE Adjust the regulated pressure under flow conditions while accessory is being used It is normal for the gauge to show minimal pressure loss during initial use of the tool Excessive tank pressure Move the Auto On Off lever to the Off postion If the unit doesnt shut off unplug it from the power source and contact a service technician Motor will not start Make sure power cord is plugged in and the switch is on Inspect for the proper size fuse in your circuit box If the fuse was tripped reset it and restart the unit If repeated tripping occurs replace the check valve or contact your service technician Excessive moisture in the discharge air Remove the water in the tank by draining after each use High humidity environments will cause excessive condensation Utilize Water filters on your air line NOTE Wat
8. s com 88051647 11 11 Operation of the air compressor should always be in a position that is stable Never use the air compressor on a rooftop or elevated position that could allow the unit to fall or be tipped over Use additional air hase for elevated jobs Always wear approved safety glasses with side shields when the air compressor is in use Turn off the air compressor and drain the air tank before performing any type of maintenance or disassembly of the hoses or fittings Never point any nozzle or sprayer toward any part of the body or at other people or animals Avoid using the air compressor in confined areas Always have adequate space 1 foot on all sides of the air compressor Also keep children pets and others out of the area of operation This air compressor does not provide breathable air for anyone or any auxiliary breathing device Spraying material will always need to be in another area away from the air compressor to not allow intake air to damage the air compressor filter Never utilize the air compressor in the rain or wet conditions Any electrical issues or repairs should be performed by authorized personnel such as an electrician and should comply with all national and local electrical codes The air compressor should also have the proper three prong grounding plug correct voltage and adequate fuse protection Never operate the compressor near combustible materials gasoline or sol
9. t between the motor pulley and the pump and it will deflect the belt approximately 1 2 inch STORAGE 1 When not in use the hose and compressor should be stored in a cool dry place 2 Tanks should be drained of moisture and the hose disconnected and hung with open ends down to allow moisture to drain 3 Protect the cord from possible damage by winding the cord loosely around the handle of the unit or coiling the cord up Moisture in Compressed Air Moisture in compressed air will form droplets as it comes from an air compressor pump When humidity is high or when the unit is run for an extended period of time moisture will collect in the tank If a sandblaster or paint spray gun is used water could be mixed in with the spray material A fiter or air dryer in the airline will help eliminate moisture when placed as clase to the gun as possible Maintenance Schedule Maintenance will need to be performed more frequently ifthe compressor is used in high humidity or dusty situations DAILY Check oil level and drain tank WEEKLY Check air filter and safety valve MONTHLY Blow dirt from inside motor and check belt tightness 3 MONTHS Change oil teedbackibnatitoots com Troubleshooting Guide Problem Possible Solution Air leaks at the check valve or pressure relief valve A defective check valve results in a constant air leak at the pressure release valve when there is
10. vent vapors If spraying flammable materials locate the air compressor at least 50m away from the spray area Never operate the air compressor indoors or in a confined area Always drain the air compressor tank daily or after each use If the tank develops a leak then replace the air compressor Never use the air compressor after a leak has been found or tried to make any modifications to the tank Never modify the air compressor s factory settings Which control the tank pressure or any other function ASSEMBLY Regulator Assembly 1 Remove the plugs from the plastic bag Apply thread sealant tape to the threads 2 The assembly is designed to be attached only to the pressure switch outlet see Fig 1 on page 6 by inserting the pipe nipple see Fig 2 and turning the assembly clockwise Tighten until snug The gauge should be oriented the same as the gauge already on the pressure switch see Fig 1 Attach the hose and tire chuck Check for leaks with soapy water Regulator Perey it exh poe ipoe owe Handle Assembly 1 Remove the handle screw from the base plate if preinstalled 2 Insert the handle into both Sides of the base plate Squeeze handle to fit into the special openings in the plate Fig 3 Tank a kee 3 Place a short piece of wood against the end of the handle and tap with a mallet or hammer until the hole in the handle lines up with the hole in the base plate 4
11. y guard or cover has to cause cancer and birth COMBS aii been damaged do not operate the defects or other reproductive equipment until the proper harm Wash hands after personnel have correctly repaired Tires 10 inches handiing the equipment The power cord CAUTION should be free of any moving FOR YOUR OWN SAFETY parts twisting andlor crimping Important READ INSTRUCTION MANUAL While in use and while in storage When using equipment a few COMPLETELY AND safety precautions must be CAREFULLY BEFORE Surfaces on your air compressor observed to avoid injuries and OPERATING THIS can be hot in operation and can damage Please read the complete COMPRESSOR cause serious bums if touched operating manual with due care The equipment should be allowed Keep this manual in a safe place time to cool before any Any failures made in following the safety regulations and instructions may result in an electric shock fire and or serious injury so that the information is available at all times If you give the equipment to any other person give them these operating instructions as well We accept no liability for damage or maintenance is attempted Items such as the compressor pump and the outlet tube are normally hot during and after operation For warranty purchases please keep your dated proof of purchase File or attach to the manual for safekeeping For customer sevice ca 40 28 5084 ena eedback naiot
Download Pdf Manuals
Related Search