Senco 3D0101N Use and Care Manual
Contents
1. UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR DEALER IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY This warranty gives you specific legal rights and you may also have other rights which vary from state to state REPLACEMENT OF TOOL DUE TO NATURAL DISASTER SENCO will replace any tool destroyed by an Act of God such as flood earthquake hurricane or other disaster resulting only from the forces of nature Such a claim will be honored provided that such original retail purchaser had previously submitted a completed warranty registration card for the tool and then submits proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier police department or other official governmental source To obtain instructions for filing a claim call 1 800 543 4596 CUSTOMER SATISFACTION One hundred percent customer satisfaction is our 1 goal If for any reason the product does not perform to the original purchaser s satisfaction it can be returned to the place of purchase within thirty days with dated sales receipt for a full refund of the purchase price 2006 by SENCO PRODUCTS INC CINCINNATI OHIO 45244 1611 USA www senco com 0701012. como se la despacha desde el fabricante Mantenga este manual dispo nible para que lo usen todas las personas destinadas a ha cer uso de esta herramienta Por razones de seguridad per sonal y la adecuada operaci n de esta herramienta lea y comprenda todas estas in strucciones cuidadosamente Uso de la Herramienta Espa ol e Antes de usar la herramienta lea y comprenda el manual INS TRUCCIONES DE SEGURI DAD despachado con ella RESPONSABILITES DE LEMPLOYEUR L employeur doit faire ap pliquer les consignes de s curit et toutes les autres instructions qui accompag nent cet outil tel qu il est livr par son constructeur Ayez ce manuel a la dispo sition de toutes les personnes charg es d utiliser cet outil Pour assurer la s cu rit personnelle et le bon emploi de cet outil lisez et assimilez soigneusement toutes ces instructions Utilisation de l Outil Francais O Lisez et assimilez le manuel INSTRUCTIONS DE S CU RIT livr avec cet outil avant de Putiliser e To Adjust Magazine Squeeze the gate latch and lift open gate Open Magazine e Para Ajustar el Cargador Oprima el pasador de la puerta y levantela abriendola Abra el cargador e Pour r gler le magasin Appuyer sur le verrou de porte et ouvrir le volet de magasin e Lift and shift nail disk to accept different length nails NOTE Reference points on magazine coincide with nail lengths O
3. tear will be repaired or replaced at SENCO s option during the two year warranty period If SENCO determines that repair or replacement is not feasible SENCO will refund the purchase price less reasonable deprecia tion based on actual use SENCO Cordless 1 Subject to the exceptions exclusions and limitations described below SENCO warrants that the SENCO Cordless tool will be free from defects in materials and workmanship for two years after the purchase date 2 SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for one year after the purchase date WARRANTY EXCLUSIONS The following warranty exclusions apply 1 Normal wear parts are not covered under this warranty Normal wear parts include for example isolators drive belts air filters rubber o rings seals driver blades piston stops and piston driver assembly 2 This warranty does not cover parts damaged due to normal wear misapplication misuse accidents operation at other than recommended speeds or voltage electric units only improper storage or damage resulting during shipping Products used in production industrial applications as defined by SENCO are excluded from this warranty Labor charges or loss or damage resulting from improper operation maintenance or repairs are not covered by this warranty 5 SENCO does not warrant the Wheelbarrow Compressor Engine Motor but the Compressor Engin
4. trigger may reduce the possibility of injury to you orto others working with you e To adjust the depth the fastener is driven first disconnect the air supply Las herramientas con Ga tillo Restringido solamente se pueden disparar con el gatillo Primero apriete el elemento de seguridad contra la superficie de trabajo y despu s tire del gatillo sta caracter stica es til cuando se requiere precisi n en la colo caci n de los sujetadores O Lea el Recordatorio de Seguri dad y Satisfacci n del Cliente CSSR en las cajas de sujeta dores y de las herramientas para informaci n sobre seguridad de los Gatillos Restringido y de Acci n Dual Bajo ciertas condi ciones el Gatillo Restringido puede reducir la posibilidad de heridas a su persona o a otros que trabajen con usted O Para ajustar la profundidad de clavo o engrapado debe prime ro desconectar el aire e Avec une gachette restrictive les clous ne peuvent tre tir s que dans une seule direction Appuyer d abord le palpeur de s curit sur la surface de travail puis tirer sur la gachette Cette fonction est utile pour un place ment pr cis de projectiles Lire le Rappel de S curit et Satisfaction du Client CSSR dans les boites a outils et fixa tions pour les informations de s curit concernant les D tentes a Double Action et a Restriction Dans certaines circonstances la D tente a Restriction peut r
5. Levante y rote el disco de clavos para que acepte clavos de diferentes longitudes NOTA Se encuentran puntos de referencia en la parte acu ada del carga dor de acuerdo a las longitudes de los clavos Soulever et tourner le disque a clous pour accepter les clous de diff rente dimensions NOTE Les points de rep re sur le magasin correspondent a la longueur des clous Tool Use English Place the nail coil in the maga zine Uso de la Herramienta Utilisation de l Outil Espa ol e Ponga el rollo de clavos in el cargador Francais O Placer le rouleau de clous dans le magasin O Close magazine cover and gate Make sure gate is fully latched O Cierre la cubierta del cargador y la puerta Asegurese que la puerta este completamente cerrada Fermer le volet de magasin et la porte S assurer que la porte est bien verrouill e e With a Dual Action trigger nails can be driven two ways a Position safety element against work surface and pull trigger Trigger Fire b Pull trigger and push safety element against work surface for operation each time the safety element is pushed against the work surface This bottom fire mode of operation is preferred when high speed rapid fastener placement is desired Las herramientas con gatillo de accion doble pueden ser disparadas de dos maneras a Oprima el seguro contra la superficie de trabajo y apriete e
6. RoofPro 455XP Operating Instructions Instrucciones de Operacion Mode d Emploi 2007 by Senco Products Inc Warnings for the safe use of this tool are included in this manual NFD83D Revised June 26 2007 Los avisos para el uso seguro de esta herramienta estan incluidos Replaces 1 22 07 en este manual Les consignes pour l utilisation en toute s curit de cet outil se trouvent dans ce manuel English Espanol Francais TABLE OF TABLA DE TABLE DES CONTENTS MATERIAS MATIERES Tool Use 2 Uso de la Utilisation de l outil 2 Maintenance 5 Herramienta 2 Entretien 5 Options 5 Mantenimiento 5 Options 5 Troubleshooting 6 Opciones 5 D pannage 6 Specifications 6 Identificaci n Sp cifications 6 Accessories 7 de Fallas 6 Accessoires 7 Especificaciones 6 Accesorios 7 EMPLOYER S RESPONSIBILITIES Employer must enforce compliance with the safety warnings and all other instructions which accompany this tool as shipped from the manufacturer Keep this manual avail able for use by all people assigned to the use of this tool For personal safety and proper operation of this tool read and understand all of these instructions carefully Tool Use English Read and understand SAFETY INSTRUCTIONS manual shipped with this tool before using tool RESPONSABILIDADES DEL EMPLEADOR El empleador debe hacer cumplir las advertencias de seguridad y todas las otras instrucciones que acompa an a esta herramienta
7. du ire la possibilit de se blesser ou de blesser d autres personnes Pour ajuster la profondeur a laquelle le clou est enfonc d connecter tout d abord l appareil de la source d air comprim Tool Use English Uso de la Herramienta Utilisation de l Outil Espa ol Francais e Turn wheel in direction of arrows to achieve desired depth Gire la rueda en direccion de las flechas para logar la profundidad deseada e Tourner la molette de r glage dans la direction des fleches pour obtenir la profoundeur de clouage voulue e The deflector can be rotated to change the direction of the exhaust air e El deflector puede rotarse para cambiar la direcci n del aire expedido por el mofle O Le d flecteur peut tre orient diff remment pour changer la direction de chappement d air Should a nail jam occur discon nect air supply O Sise produce un atascamiento de un clavo desconecte el suministro de aire e Au cas ou il se produirait un coincage de clous coupez l alimentation en air Press down on the gate latch and lift open gate Presione hacia abajo el pestillo de la puerta de alimentaci n y deje abierta la puerta de alimentaci n e Appuyer sur le verrou du volet de la chambre d alimentation et soulever pour ouvrir e Extract bent nail from rear of guide body e Extraiga el clavo doblado des de atr s del cuerpo gu a e Ext
8. e en contacto con SENCO para informaci n 1 800 543 4596 e Antes de usar la herramienta lea y comprenda el manual INS TRUCCIONES DE SEGURIDAD despachado con ella AVERTISSEMENT Les r parations autres que celles d crites ici doivent tre r alis es uniquement par du personnel qualifi ayant recu la formation appropri e Pour toute information prenez contact avec SENCO par t l phone en appelant Le Distributeur agr O Lisez et assimilez le manuel INSTRUCTIONS DE S CU RITE livr avec cet outil avant de l utiliser SYMPTOM Air leak near top of tool Sluggish operation SOLUTION Verify air supply tighten screws or install Parts Kit YKO424 SYMPTOM Air leak near bottom of tool Poor return SOLUTION Clean tool tighten screws or install Parts Kit YKO425 SYMPTOM Other problems SOLUTION Contact SENCO Specifications English SINTOMA El aire se escapa cerca de la parte su perior de la herramienta Operaci n lenta SOLUCION Apriete los tornillos Verifique el suministro de aire o instale el Juego de Partes Parts Kit YK0424 SINTOMA El aire se fuga cerca de la parte inferior de la herramienta Mal retorno SOLUCI N Apriete los tornillos Limpi la herramienta o instale el Juego de Partes Parts Kit YK0425 S NTOMA Otros problemas SOLUCI N P ngase en contacto con SENCO Especificaciones Espa ol SYMPT ME Fui
9. e Motor may be covered under a warranty offered by its manufacturer RO GENERAL WARRANTY CONDITIONS This warranty will be honored only if A Clean dry regulated compressed air has been used at air pressure not exceeding the maximum indicated on the tool casting B No evidence of abuse abnormal conditions accident neglect misuse or improper modifications or storage of the product and C No Deviation from operating instructions specifications and maintenance schedules exists read Operator Manual for use specifications and main tenance instructions THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT AND SENCO DISCLAIMS ALL OTHER WARRANTIES ANY IMPLIED WARRANTIES WILL BE LIM ITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU YOUR REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED ABOVE SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL CONSEQUENTIAL INDIRECT OR SPECIAL DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL SENCO S LIABILITY EXCEED THE PRICE OF THE PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR LIABILITY ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE
10. ense any product or part that is defective in materials or workmanship after examination by a SENCO Authorized Warranty Service Center subject to the exceptions exclusions and limitations described below Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced product or part A DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A WARRANTY CLAIM Warranty registration also is required and can be accom plished through on line Product Registration at www senco com or by completing and returning the postage paid warranty registration form included with your Operator s manual parts chart information found inside the product carton To make a warranty claim you must return the product with proper receipt proof of purchase and return transportation charges prepaid to a SENCO Authorized Warranty Service Center A list of SENCO Authorized Warranty Service Centers can be found at www senco com or by calling 1 800 543 4596 toll free SENCO will perform its obligations under this warranty within a reasonable time after approval of the warranty claim Wheelbarrow Compressors 1 Subject to the exceptions exclusions and limitations described below SENCO warrants that the compressor pump will be free from defects in mate rials and workmanship for two years after the purchase date 2 Defective parts of the compressor pump not subject to normal wear and
11. irper le mauvais clou par larri r du front ALTERNATIVE Insert a rod and push the point of the nail back up and into the guide body bore LA ALTERNATIVO Inserte una varilla y empuje la punta del clavo hacia el barreno del cuerpo guia OU Ins rer une tige et repousser la pointe du clou dans l al sage du front Extract the nail with pliers or if the nail is loose turn the tool upside down and shake it out e Extraiga el clavo con pinzas o d le vuelta a la herramienta y ag tela e Extraire le clou avec des pinces ou retourner et secouer l appa reil pour faire tomber le clou s il est libre al iy Maintenance English Read and understand SAFETY INSTRUCTIONS manual shipped with this tool before using tool Mantenimiento Espa ol Antes de usar la herramienta lea y comprenda el manual INS TRUCCIONES DE SEGURI DAD despachado con ella Entretien Francais Lisez et assimilez le manuel INSTRUCTIONS DE SECU RITE livr avec cet outil avant de l utiliser All screws should be kept tight Loose screws result in unsafe operation and parts breakage Todos los tornillos tienen que mantenerse apretados Los tornillos sueltos pueden producir una operaci n no segura y quebraduras de partes O Toutes les vis doivent tre maintenues serr es a fond Les vis desserr es entrai nent un manque de s ret du fonctionneme
12. l gatillo Disparo de gatillo b Para impulsar un clavo oprima el disparador y deprima el elemento de seguridad contra la superficie de trabajo Cada vez que deprima el elemento de seguridad contra la superficie de trabajo impulsara un clavo Este modo de operaci n de disparo inferior o por rebote es el preferido cuando se desea alta productividad y r pida colocaci n del clavo O Les appareils quip s de d clenchement au touch par g chette peuvent tre utilis s de 2 facons diff rentes a D clenchement par g chette Appliquer le palpeur de s curit de l appareil l endroit d sir et activer la g chette b Pour planter un clou tirez sur la d tente et poussez l l ment de s curit contre la surface de travail Chaque fois que l l ment de s curit est pouss contre la surface de travail un clou est plant Le mode de fonctionnement en tir continu est pr f rable si vous d sirez placer des attaches rapidement avec forte productivit With a Restrictive trigger nails can only be driven one way First depress safety element against work surface then pull trigger This feature is helpful when precise fastener placement is required e Read the Customer Satisfaction and Safety Reminder CSSR in the tool and fastener boxes for safety information regarding the Dual Action and Restrictive triggers Under certain condi tions the Restrictive
13. ngs and other tool parts Solamente si es necesario use soluciones para limpieza no flamabl s NO LA REMOJE Precauci n Tales soluciones pueden da ar los empaques y otras partes de la herramienta e Nettoyez l outil chaque jour a l aide d un chiffon et inspectez le pour d celer une ventuelle usure Utilisez uniquement des solvants non inflammables en cas de n cessit NE LE FAITES PAS TREMPER Attention De tels produits peuvent endommager les joints et d autres pi ces de l appareil Options English SINGLE SEQUENTIAL TRIGGER This feature is helpful when precise fastener placement is required Opciones Espanol GATILLO RESTRINGIDO Esta caracteristica sirve de ayuda cuando se requiere una colocaci n del sujetador precisa Options Francais O DECL NCHEMENT PAR GACHETTE Cette caract ristique s av re utile quand un placement de projectiles pr cis s impose Troubleshooting English Identificaci n de Fallas Espa ol D pannage Francais WARNING Repairs other than those described here should be performed only by trained qualified personnel Contact SENCO for information at 1 800 543 4596 e Read and understand SAFETY INSTRUCTIONS manual shipped with this tool before using tool ALERTA Las reparaciones fuera de aquellas descritas aqu deben de ser lleva das a cabo solamente por personal entrenado y calificado P ngas
14. nt et la rupture de pi ces With tool disconnected make daily inspection to assure free movement of safety element and trigger Do not use tool if safety element or trigger sticks or binds Con la herramienta desconec tada haga inspecciones diarias para asegurar el movimiento libre del seguro y del gatillo No use la herramienta si el seguro o el gatillo se atoran O Loutil tant s par de Palimentation en air effectuez une inspection journali re pour assurer le libre mouvement du palpeur de s curit et de la d tente N utilisez pas l outil si le palpeur de s curit ou la d tente colle ou se coince e Squirt Senco pneumatic oil 5 to 10 drops into the air inlet twice daily Depending on frequency of tool use Other oils may damage O rings and other tool parts e Aplique aceite neum tico Senco en la entrada de aire dos veces al d a Dependiendo en la frecuencia de uso 5 A 10 Gotas Otros aceites pueden da ar los anillos en 0 y otras piezas de la herramienta e Avec une burette placer 5 a 10 gouttes d huile pneumatique dans l arriv e d air deux fois par jour D pend de l intensit de l utilisation de l appareil D autres huiles pourraient en dommager les joints toriques et d autres pi ces de l outil Wipe tool clean daily and inspect for wear Use non flammable cleaning solutions only if nec essary DO NOT SOAK CAUTION Such solutions may damage O ri
15. os por segundo 8 8 Peso 2 4 kg 5 4 Ibs Capacidad de clavos por cargador 120 120 Longitudes de los clavos 19 44 mm 3 4 in 13 4 in Mango del clavo 3 0 mm 120 Tama o de la herramienta Altura 267 mm 10 in Tama o de la herramienta Longitud 260 mm 10 ain Tama o de la herramienta Ancho Cuerpo 76 mm 3 in Tama o de la herramienta Ancho Cargador 114 mm 4 1 2 in Francais RoofPro455XP RoofPro455XP Pression de travail min et max 4 8 8 3 bar 70 120 psi Consommation d air 60 cycles par minute 185 liter min 6 54 scfm Prise d air 1 4 in NPT 1 4 in NPT Vitesse maximum cycles par seconde 8 8 Poids 2 4 kg 5 4 lbs Capacit de clous par magasin 120 120 Dimensions des clous longueur 19 44 mm 3 4 in 13 4 in Dimensions des clous diam tre 3 0 mm 120 Dimensions de Poutil hauteur 267 mm 10 in Dimensions de l outil longueur 260 mm 10 Ain Dimensions de l outil largeur corps de l appareil 76 mm 3 in Dimensions de l outil largeur magasin 114mm 4 thin Accessories English Accesorios Espa ol Accessoires Francais SENCO offers a full line of accesso ries for your SENCO tools including Air Compressors Hose Couplers Fittings Safety Glasses Pressure Gauges O Lubricants Regulators Filters For more information or a complete illustrated catalogue of SENCO accessories ask your representative for MK336 SENCO ofrece una linea completa de Accesorios pa
16. ra sus herramien tas SENCO incluyendo Compresores de Aire Manguera O Conectores Rapidos O Conectores O Anteojos De Seguridad Manometros O Lubricantes Reguladores O Filtros Para mas informacion un pour recevoir un catalogo completo ilus trado de los Accesorios SENCO pregunte a su representante pour el numero MK336 SENCO offre une gamme tendue d accessoires pour vos outils SENCO y compris Compresseurs O Tuyauterie flexible O Raccords O Lunettes de s curit Manom tres Lubrifiants R gulateurs O Filtres Pour plus d informations ou pour recevoir un catalogue d taill des accessoires propos s par SENCO prenez contact avec votre repr sentant SENCO r f rence catalogue MK336 Limited Warranty SENCO Pneumatic DuraSpin Cordless Tools amp Compressors Senco Products Inc SENCO designs and constructs its products using the highest standards of material and workmanship SENCO war rants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty period specified below SENCO XP Series SENCO PRO Series SENCO Compressors Five years One year One year SENCO DuraSpin SENCO Cordless SENCO Reconditioned Products One year Two years One Year During the warranty period which begins on the purchase date SENCO will repair or replace at SENCO s option and exp
17. te d air pr s du sommet de l outil fonctionnement lent SOLUTION Serrez les vis fond v rifiez l alimentation en air ou remplacez YKO424 SYMPTOME Fuite d air pr s de la base de l outil retour inad quat SOLUTION Serrez les vis fond nettoyez l outil ou remplacez YK0425 SYMPT ME Autres probl mes SOLUTION Prenez contact avec SENCO Specifications Fran ais Smooth 10 mm 394 in 19mm 3 4 22 mm 7 8 25 mm 1 32 mm 1 1 4 38 mm 1 1 2 44 mm 13 4 3 0 mm 120 in RoofPro455XP RoofPro455XP TECHNICAL SPECIFICATIONS Min to max operating pressure 70 120 psi 4 8 8 3 bar Air Consumption 60 cycles per minute 6 54 scfm 185 liter min Air Inlet 1 4 in NPT 1 4 in NPT Maximum Speed cycles per second 8 8 Weight 5 4 Ibs 2 4 kg Nails per Magazine Capacity 120 120 Nail Lengths 3 4 in 13 4 in 19 44 mm Nail Shank 120 3 0 mm Tool size Height 10 2 in 267 mm Tool size Length 10 ain 260 mm Tool size Width Main Body 3 in 76 mm Tool size Width Magazine 4 1 2 in 114 mm Espa ol ESBEDINCACIONES TECNICAS RoofPro455XP RoofPro455XP Presi n de operaci n m nima y m xima 4 8 8 3 bar 70 120 psi Consumo de aire 60 ciclos por minuto 185 liter min _ 6 54 scfm Entrada de aire 1 4 in NPT 1 4 in NPT Velocidad m xima cicl
Download Pdf Manuals
Related Search