Global Door Controls GLA10SSUN-626 Installation Guide
Contents
1. correct knob out K LE direction N BACKSET 70mm 2 3 4 AA BACKSET 60mm 2 3 8 DOWNWARD CORRECT UPWARD INCORRECT V X TEMPLATE Fit here on door edge ep eee 5145 40 35 32 2 1 3 4 1 9 16 1 3 8 1 1 4 5 5mm 7 32 x2 HOLE 8mm 5 16 DEEP FOR METAL DOOR ONLY Mark 1 25 4mm hole at center of door edge EA1 Rev 10 21 20082. remove inside rose plate Remove inside rose and mounting plate 8 INSTALL INSIDE ROSE A FOR WOODEN DOOR Tighten machine screws securely to install mounting plate Press rose onto mounting plate Be sure to fit rose in recess of mounting plate EA1 6 ADJUST OUTSIDE ROSE 7 INSTALL LOCK Adjust lock to fit door thickness by rotating outside rose Lock will fit all doors 1 3 8 to 1 3 4 35mm 45mm thick CENTER LINE B FOR METAL DOOR MOTE Make sure that mounting plate fit horizontally into slots notched in door Latch unit must be in place before installing lock Be sure lock housing engages with latch prongs and retractor interlocks with latch tail 9 INSTALLATION OF INSIDE KNOB IMPORTANT Align lug on knob with narrow slot on side of spindle and push knob all the way in until knob catch clicks into slot on knob Otherwise knob will jamb on shaft 10 RIGHT KEY HOLE POSITION 11 IN ORDER TO ADJUST THE ABNORMAL STATE OF THE KEY HOLE FACING UPWARD THE KNOB MUST BE PULLED OUT AND INSTALLED AGAIN that key hole faces upward or downward as shown in the following drawing It is advisable to correct all key hole to be facing downward a First turn the knob clockwise until the knob catch appears in the small hole b With the other hand turn the key counterclockwise within the limit of 30 90 c Using a small nail Install again to press the knob according to catch and pull the Nl y the
3. EA1 EA1 INSTRUCTIONS FOR INSTALLATION OF ENTRANCE LOCKS IN NEW DOORS OR THE REPLACEMENT OF EXISTING LOCKS FOR USE ON DOORS 1 3 8 TO 1 3 4 TOOLS REQUIRED FOR REPLACEMENT 35mm 45mm THICK INSTALLATION 1 phillips head screwdriver TOOLS REQUIRED FOR NEW INSTALLATION 1 phillips head screwdriver ILLUSTRATIONS ARE SHOWN WITH 1 2 1 8 54mm hol HL Aas Aaa ENTRANCE MODELS INSTALLATION IS TS SAME FOR PRIVACY AND PASSAGE MODELS AS WELL FOLLOW ALL STEPS FOR REMODELING OR NEW CONSTRUCTION CYLINDRICAL CASE FOLLOW STEPS 3C 4C 5 6 7 8 9 and 10 herons FOR DO IT YOURSELF REPLACEMENT AFTER REMOVAL OF EXISTING LOCK OUTSIDE KNOB OUTSIDE ROSE REPLACING EXISTING LOCKS Before beginning measure from center of lock to door edge in order to check length of backset on existing lock The backset length of new lock is stated clearly on front of package If backset size is the same you ll have to replace lock with proper size INSIDE ROSE backset INSIDE KNOB LATCH RETRACTOR LATCH UNIT GUARDBOLT MOUNTING SCREWS SCREW HOLE LATCHBOLT LATCH FACE INSTALLATION INSTRUCTIONS 1 MARK DOOR MARK FOR 1 Start approximately 36 Drill 2 1 8 54mm hole through door 25 4mm 914mm from floor Fold face as marked for lockset iem ae eee It is recommended that holes be drilled door edge as indicated on from both sides to prevent splitting template Mark center hole Drill 1 25 4 mm hole in center o
4. f on door face through guide door edge for latch on template MARK FOR 2 1 8 p 54mm HOLE ON NOTE Backset on door face must be 2 1 8 54mm 1 25 4mm DOOR FACE same as backset of lock HOLE 3 INSTALL LATCH Insert latch in hole keeping it Chisel 5 32 4mm Insert latch and tighten parallel to face of door Mark deep or until latch screws outline and remove face is flush with NOTE Latchbolt bevel door edge must face to closing direction ay qu Cut out jamb 1 16 GUARD BOLT Drill 1 25 4mm 1 5mm deep for hole 1 2 12 7mm strike Tighten screws deep in door jamb g STRIKE on drill point for Guardbolt stops against i strike as illustrated Close door until latchbolt touches jamb to strike K preventing forcing when locate strike in jamb and center line of strike F door is closed Adjustable Open door and extend line from mark to door CAUTION To ensure proper lockset function l i tang on strike permits stop Measure one half of door thickness from Hole in jamb must be drilled a full S bending in or out to door stop and vertically mark drill point center 1 2 12 7mm deep eliminate too loose fit between door and for strike door stop EA1 EA1 EA1 5 REMOVE INSIDE TRIM Use nail end of wrench provided to depress A inside knob catch in hole of inside sleeve collar and slide knob or in side lever off spindle Depress spring attached to inside rose Insert nail end of wrench into slot to
Download Pdf Manuals
Related Search