Hager AE-4701RIMUS32D Installation Guide
Contents
1. 4700 Series Rim Exit Device HAGER Installation D COMPANIES DEVICES COVERED IN THESE INSTRUCTIONS 4700R Rim exit device 4700RF Fire Exit Rim exit device OVERVIEW Door Handing OUTSIDE OF DOOR a Pe i OFr 9 iar INSIDE OF DOOR RIM EXIT DEVICE E SURFACE VERTICAL ROD EXIT DEVICE 2 3 4 2 3 4 70 mm 70 mm For wood drill 1 8 hole Drill 5 16 thru from device side Drill 3 8 from other side pull side Machine Screws con 7 Drill 1 4 20 Tap Check building and fire codes to see if your application requires the use of sleeve nuts and bolts REV 2 Page 1 of 3 4700 Series Rim Exit Device HAGER Installation ee COMPANIES 1 CUT EXIT DEVICE TO LENGTH 2 MARK DOOR AND DRILL MOUNTING HOLES The exit device is pre cut for 36 and 48 wide door use For other Measure center line of exit device typically 40 from finished floor Fold and door widths cut exit device to appropriate length Recommended apply template to door and up against stop Mark and drill holes as shown on overall length of the exit device is equal to door width minus four template Be sure the vertical line of the exit device2. DOOR WIDTH 4 For metal doors drill and tap for 1 4 20 machine screws For wood doors pre drill 1 8 holes For sex bolts drill 5 16 clearance holes on exit device side push side and 3 8 on pull side CAM MATES WITH TRIM ACTUATING SHAFT If using trim be sure to line up trim actuating shaft tailpiece with cam located on back of exit device chassis Metal door sex bolt Screws 1 4 20 machine Metal door sex bolt or trim 1 4 20 screws 2 i Wood door machine screws 2 Wood door 12 wood screws 2 12 wood screws 2 REV 2 Page 2 of 3 4700 Series Rim Exit Device j Installation Instructi HAGER nstallation ype COMPANIES 5 INSTALL STRIKE 6 INSTALL COVER Install strike using only the top and bottom slotted holes and 1 4 20 machine screws Install head cover on chassis using provided screws metal or pre drill 1 8 hole for 12 wood screw Open and close door to verify latch and deadlatch are aligned properly For tight fit move strike away from door For loose fit move strike towards door Once strike is adjusted install center screw STEP 1 INSTALL STRIKE USING TWO OUTER SLOTTED HOLES Screws Metal stop 1 4 20 machine screws 3 Wood stop 12 wood screws 3 STEP 2 ADJUST STRIKE STEP 3 INSTALL SCREW TO TIGHT FIT MOVE STRIKE AWAY FROM DOOR LOCK STRIKE IN POSITION LOOSE FIT MOVE STRIKE TO WARDS DOOR 7 DOG DEVICE For increasi
3. mounting holes is 2 1 4 inches Cut with hack saw or metal cutting saw blade Deburr from the face of the stop Do not drill center hole on strike until after strike edges has been mounted and adjusted DOOR WIDTH RANGE FOR EXIT DEVICES 36 DEVICE 30 36 DOOR WIDTH 48 DEVICE 36 48 DOOR WIDTH STRIKE EXIT DEVICE MOUNTING MOUNTING HOLE DOOR WIDTH HOLES TRIM ACTUATOR T EXIT DEVICE MOUNTING HOLE 2 1 4 57 mm For metal doors drill and tap for 1 4 20 machine screws for both exit device and strike For wood doors pre drill 1 8 holes If mounting trim drill 5 16 clearance holes on exit device side push ee PRAM TEIS END side of door and 1 2 holes on pull side Trim requires an additional 1 2 clearance hole for the trim actuating shaft not required for dummy trim If using sex bolts drill 5 16 clearance holes on exit device side push side of door and 3 8 holes on pull side 3 INSTALL DEVICE 4 INSTALL END CAP Remove head cover Remove end cap from end cap bracket Mark hole locations by either using from exit device chassis template or holding end cap bracket up against door Be sure exit device is Mount exit device using level before inserting end cap bracket lip into end of device body Mark and the 2 mounting holes drill tap holes Install end cap bracket and end cap indicated on template RECOMMENDED OVERALL EXIT DEVICE LENGTH
4. ng the life of this device dog device down during high traffic periods of the day A dogging device is not available on fire rated models Dogging Depress push bar insert dogging hex wrench and turn clockwise 90 degrees The push bar will remain depressed and the latch will stay retracted Release Dogging Hold push bar insert dogging hex wrench and turn counterclockwise 90 degrees The push bar will return to the up position and latch will extend to lock door RELEASE DOGGING REV 2 Page 3 of 3
Download Pdf Manuals
Related Search