Husky H4130 Use and Care Manual
Contents
1. Maintenance Ensure the air line is shut off and drained of air before removing this tool for service This will prevent the tool from operating if the throttle is accidentally engaged LUBRICATION operation An in line filter regulator lubricator is recommended as it increases tool life and keeps the tool in sustained Regularly check and fill the in line lubricator with air tool oil Avoid using excessive amounts of oil Adjust the in line lubricator by placing a sheet of paper next to the tool s exhaust ports and holding the throttle open approximately 30 seconds The lubricator is properly set when a light stain of oil collects on the paper If it is necessary to store the tool for an extended period of time overnight weekend etc generously lubricate the tool through the air inlet Run the tool for approximately 30 seconds to ensure the oil is evenly distributed throughout the tool Store the tool in a clean and dry environment agents and an EP extreme pressure additive Troubleshooting Recommended lubricants Air tool oil or any other high grade turbine oil containing moisture absorbent rust inhibitors metal wetting Problem Possible Cause Solution The tool runs slowly or will not operate There is grit or gum in the tool Flush the tool with air tool oil or gum solvent The tool is out of oil Lubricate the tool according to the lubri2. cation instructions in this manual The air pressure is low Adjust the regulator on the tool to the maximum setting Adjust the compressor regulator to the tool s maximum setting of 90 psi The air hose leaks Tighten and seal the hose fittings with pipe thread tape if leaks are found The air pressure drops Ensure the hose is the proper size Long hoses or tools using large volumes of air may require a hose with an I D of 2 or larger depending on the total length of the hose Do not use a multiple number of hoses connected together with a quick connect fitting This causes additional pressure drops and reduces the tool power Directly connect the hoses together There is a worn rotor blade in the motor Replace the rotor blade There is a worn ball bearing in the motor Remove and inspect the bearing for rust dirt and grit Replace or clean and grease the bearing with bearing grease There is moisture blowing out of the tool s exhaust There is water in the tank Drain the tank See the air compressor manual for instructions Lubricate the tool and run it until water is not evident Lubricate the tool again and run for 1 2 seconds HUSKYTOOLS COM Please contact 1 888 43 HUSKY for further assistance Service Parts 46 Reference Part Number Description Reference Part Number D
3. escription Number Number 1 933 312301 Housing 27 9030129 Needle Bearing 2 950102 Spring Pin 28 933 301328 Ratchet Housing 3 933 312303 Air Inlet 29 930129 Bushing 4 933 301304 Throttle Lever 30 933 301330 Crank Shaft 5 933 301305 Throttle Valve 31 933 301331 Drive Bushing 6 933 312306 Valve 933 301332 Yoke 7 9706109 O Ring 933 301333 Reverse Button 8 933 301308 Spring 933 301334 Spring 9 90R01000105 1 0 Ring 933 301335 Lock Ring 10 933 312310 Valve Plug 930136 Washer 11 90R02607108 O Ring 930137 Ratchet Pawl 12 933 301307 Throttle Valve 930138 Ratchet Anvil 3 8 13 9052213 Ball Bearing 930139 Spring 2 14 9301114 Rear End Plate 930140 1 Pin 15 930115 Rotor 933 301336 Thrust Washer 16 930116 Rotor Blade 4 930142 Retainer Ring 17 930117 Pin 2 930143 Steel Ball 2 18 950118 Cylinder 930107 V 0 Ring 19 933 301319 Front End Plate 970117 Spring Pin 20 9030120 Ball Bearing 9P91237 0 Ring 21 930121 Washer 933 302312 Damping Material 22 930122 Thread Ring Gear 933 302311 Deflector 23 933 3013L23 Idler Gear 3 933 312352 Grip 24 930124 Idler Gear Pin 3 980225 Bushing 3 25 930125 Idler Gear Plate 51 9526212 Decoration Ring 26 933 312317 Clamp Plate 52 930152 Rubber Boot
Download Pdf Manuals
Related Search