Kawasaki 840107 Use and Care Manual
Contents
1. ee 6 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS 6 SAFETY RULES FOR CORDLESS DRILL DRIVERS 6 7 SYMBOLS sue el acp Ed xa ieee 7 SECTION THREE FUNCTIONAL DESCRIPTION 8 BATTERY Arcane eee RETE eee aces odes 9 11 REMOVING ATTACHING BATTERY PACK 10 CHARGER caa tenik 10 CHARGING BATTERY PACK 11 ASSEMBLY edo a OE E 11 12 INSTALLING DRILL BIT INTO KEYLESS CHUCK 11 12 OPERATING THE DRILL cde iener EAE Rak 12 15 VARIABLE SPEED TRIGGER SWITCH erre rms 12 FORWARD REVERSE AND TRIGGER LOCK LEVER 13 TORQUE SETTINGS 3 5 ta ROG eed Ra dn i 13 SDREWDRIVING uid dct RS Deb epe CREER RIP ORE i 14 DRILLING METAL oi geese pees sd 14 DRILLING MASONRY 14 DRILLING WOOD edP eea ane weed acer 14 HINTS FOR OPTIMUM get EE REESE ERES 15 SECTION FOUR MAINTENANCE AND CLEANING 15 16 1 PUCESOURIEDS saved seek dee e exp dee a nis 16 SPECIFICA MONS MEER TTE 17 PROTECTING THE ENVIRONMENT 17 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 17 SECTION FIVE 2 YEAR LIMITED 17 20 CONGRATULATIONS2. Carrying power tools with your finger on the switch or inserting battery pack into a tool or energizing power tool with the power switch ON invites accidents Remove adjusting keys or wrenches before turning the tool ON A wrench or a key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper foot ing and balance enable better control of the tool in unexpected situations Use personal protective equipment Always wear eye protection Protective equipment such as dusk mask non skid safety shoes hard hat or hearing protec tion used for appropriate conditions will reduce personal injuries If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collec tion can reduce dust related hazards POWER TOOL USE AND CARE A CAUTION Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safe
3. LEVER NOTE Be sure the trigger is released when changing the position of the lever Always store the tool in the LOCKED OFF position Always check the direction of the Cordless Drill s rotation before use TO SELECT THE DIRECTIONS OF ROTATION To select forward Cordless Drill rotation press the trigger lock from left to right flat against the Cordless Drill body To select reverse press the trigger lock lever in the opposite direction The center position locks the tool 13 THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE For light duty work use lower settings CONTROL RING For heavy duty work use higher settings PROPER SETTING FOR DRIVING SCREWS 1 Set the ring on the lowest setting to begin 2 Try tightening the first screw If the drill drives smoothly proceed with the next screw 3 If the Drill s clutch slips increase the torque setting and try again until the Drill drives the screw without incident INSTALLING DRIVE BIT INTO KEYLESS CHUCK A WARNING Before inserting a drill bit or other accessory make sure the forward reverse and trigger lock lever is in the center OFF position to prevent accidental starts that may result in injury Do not attempt to tighten drill bits or any other accessory by gripping the front of the chuck and turning the tool on This may cause personal injury and or damage to the chuck When re
4. are removed from the Class 11 Construction Denotes Double Insulation Cordless Drill before switching the tool ON Keys or wrenches can fly away min Minutes Time at high velocity striking you or a bystander S Seconds Time When using the Cordless Drill always maintain a firm grip on the tool with Diameter Size of Drill Bits both hands Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator Keep the handle of the Cordless Drill dry clean and free from oil and grease Do not run the Cordless Drill while carrying it at your side A spinning sock et or bit could become entangled with clothing and injury may result Grinding Wheels etc n No load speed No load Rotational Speed min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 2 3 Ring Selector Settings Speed Torque or Position Settings FUNCTIONAL DESCRIPTION BATTERY A WARNING Before using battery pack please read carefully all instruc tions and cautionary markings on battery pack battery charger and product using battery Do not incinerate the battery pack even if it is severely dam aged or is completely worn out The battery pack can explode Do not carry battery packs in aprons pockets or tool boxes product kit boxes drawers etc with loose metal obj
5. ATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE 21 Limitations on Warranty Disclaimer
6. FOR CUSTOMER SERVICE POUR LE SERVICE APRES VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Imprim dans la Chine Impreso en China Kawasaki Kawasaki Motors Corp U S A OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO KAWASAKI EST UNE MARQUE DE COMMERCE DE KAWASAKI MOTORS CORP U S A QUI NE FABRIQUE PAS ET NE DISTRIBUE MATEURS DOIVENT ETRE ADRESSEES A KAWASAKI ES UNA MARCA REGISTRADA CON LICENCIA DE KAWASAKI MOTORS CORP E U A QUE NO FABRICA NI DISTRIBUYE ESTE PRODUCTO LAS CONSULTAS DE LOS CONSUMIDORES DEBEN DIRIGIRSE A COPYRIGHT 2010 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 690505 18V Black Cordless Drill Perceuse sans fil noire de 18 V aladro inal mbrico negro de 18V_Rev 1 7 10 PAS CE PRODUIT THIS PRODUCT LES QUESTIONS DES CONSOM COMPONENT m COMPOSANT awasaki 690505 18V BATTERY OPERATED DRILL INSTRUCTION MANUAL MANUEL D INSTRUCTIONS POUR PERCEUSE SANS FIL KAWASAKI 18 V MANUAL DE INSTRUCCIONES PARA EL TALADRO INALAMBRICO DE 18V THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS
7. INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND OR PROPERTY DAMAGE CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA S CURIT LE FONCTIONNEMENT ET LE REMISAGE DE CE PRODUIT LIRE TUDIER ET VEILLER BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS ET AUTOCOLLANTS APPOS S SUR LE PRODUIT AVANT DE L UTILISER NE PAS RESPECTER CES INSTRUCTIONS POURRAIT ENTRAINER DES BLESSURES ET OU DES DOMMAGES MAT RIELS ESTE MANUAL CONTIENE INFORMACI N IMPORTANTE SOBRE LA SEGURIDAD OPERACI N MANTENIMIENTO Y ALMACE NAMIENTO DE ESTE PRODUCTO ANTES DE USARLO LEA Y COMPRENDA TODAS LAS PRECAUCIONES ADVERTENCIAS NSTRUCCIONES Y ETIQUETAS DEL PRODUCTO DE LO CONTRARIO PODR A SUFRIR LESIONES GRAVES 0 CAUSAR DANOS MATERIALES F YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US POUR TOUTE QUESTION OU EN CAS DE PROBLEME AVEC LE PRODUIT ALLTRADE NE PAS LE RETOURNER AU MAGASIN OU IL A T ACHET APPELER LE SERVICE APRES VENTEAU 1 800 590 3723 AVANT D APPELE
8. R VEILLER A SE PROCURER LES NFORMATIONS SUIVANTES No DE MODELE DATE DE LACHAT ET ADRESSE DU MAGASIN UN REPR SENTANT D ALLTRADE PEUT R SOUDRE VOTRE PROBLEME PAR T L PHONE POUR TOUT COMMENTAIRE OU SUGGESTION N H SITEZ PAS NOUS APPELER OU NOUS CONTACTER PAR COURRIEL A L ADRESSE INFO ALLTRADETOOLS COM VOS COMMENTAIRES NOUS SONT EXTR MEMENT PR CIEUX SI TIENE DUDAS 0 SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1 800 590 3723 ANTES DE LLAMAR TENGA A MANO LA SIGUIENTE INFORMACI N No DE MODELO FECHA DE COMPRA Y DIRECCI N DE LA TIENDA UN REPRESENTANTE DE ALLTRADE PUEDE RESOLVER SU PROBLEMA POR TEL FONO SI DESEA HACER ALGUNA SUGERENCIA COMENTARIO LLAMENOS 0 ENV ENOS UN MENSAJE DE CORREO ELECTR NICO A INFOGALLTRADETOOLS COM SUS COMENTARIOS SON FUNDAMENTALES PARA NOSOTROS TABLE OF CONTENTS CONGRATULATIONS 2 INTENDED USE iussu ed o Eee Tre Set re XR 2 SECTION ONE GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 2 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 WORK AREA 4 ELEGIBIGAL SAFETY 4 PERSONAL SAFETY ae ee ements 4 5 TOOL DSE ANB CARE 5 SERVICE
9. Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool GENERAL SAFETY WARNINGS FOR ALL BATTERY OPERATED TOOLS 4 WARNING READ AND UNDERSTAND ALL SAFETY WARNINGS AND INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death 2 DANGER indicates an imminently hazardous situation which if not avoided will result in dea
10. all metal objects that can make a connection from one terminal to another Shorting the battery termi nals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes addition ally seek medical help Liquid ejected from the battery may cause irritation or burns Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is main tained Follow instructions in the Maintenance section of this manual Use of unautho rized parts or failure to follow Maintenance Instructions may create a risk of shock Or injury 4 CAUTION Disconnect the plug or remove the battery pack from tool and place the switch in the locked or OFF position before making any assembly adjustments changing accessories performing any inspection maintenance or cleaning procedures Such preventive safety measures reduce the risk of starting the tool accidentally Do not use the Cordless Drill if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid Maintain labels and nameplates on the Cordless Drill These carry important information If unreadable or missing contact Alltrade for a replacement SYMBOLS th tor bi istud IMPORTANT Some of the following symbols may be used on your tool Pl
11. attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table on next page 17 RECOMMENDED SIZES OF EXTENSION CORDS FOR 120 VOLT AC 60 HZ TOOLS CURRENT RATING IN AMPS CONDUCTOR SIZE IN A W G MORE THAN NOTMORETHAN 25 FT 90 FT 100 FT 150 FT 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 NOT RECOMMENDED SPECIFICATIONS SPECIFICATIONS Voltage 18V 7 Speed 0 600 min Torque Settings 25 Drill Chuck Capacity max Charger Input Charging Time 10mm 3 8 120V N 60Hz Approx 3 5 hours Battery Type Ni Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recycle batteries with due care for our environment Ni Cad and Ni MH batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordles
12. certain latches fasten securely Cordless Drill will not operate properly if the battery pack is not seated properly 120V AC ADAPTER Po co ASSEMBLY WARNING Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always turn the switch OFF and remove the battery pack before changing bits Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid 11 12 OPERATING THE DRILL WARNING Never tape the trigger switch down to provide continu ous high speed The tool may fail under such conditions causing fire or personal injury TORQUE SETTINGS NOTE To prevent damaging the tool or driving screw too deep into work piece release the trigger when you feel the clutch slip VARIABLE SPEED TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH The speed of the Cordless Drill depends on the amount of pressure you put on the trigger The more pressure you apply the faster the Cordless Drill will go Release the pressure and the Cordless Drill will slow down FORWARD REVERSE AND TRIGGER LOCK
13. d to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace 19 the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for l
14. ea and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING Handling the power cord on corded products may expose you to lead a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling A WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may cause accidents or injury Do not operate power tools in explosive areas such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control ELECTRICAL SAFETY A WARNING A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery A charger that may be suitable for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designated battery pack Use of any other batteries may create risk of fire Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radia t
15. ease study them and learn their meaning Proper interpretation of these symbols will SAFETY RULES FOR CORDLESS DRILL DRIVERS SEU EEO RS Bus uai allow you to operate the tool better and safer CAUTION SYMBOL NAME SPECIFIC SAFETY RULES AND OR SYMBOLS 4 CAUTION Hold tool by insulated gripping surfaces when perform ing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock EXPLANATION Always wear safety goggles or eye protection when using this tool Use a Volts Voltage Potential dust mask or respirator for applications which generate dust A Amperes Current Do not grasp the tool or place your hands too close to the spinning chuck or Hz Hertz Frequency Cycles per Second drill bit Your hand may be lacerated or may cause injury W Watt Power Secure the material being worked on Never hold it in your hand or across Kg Kilograms Weight your legs Unstable support can cause loss of control and injury NI Alternating Current Type of Current Direct Current Type of Current Position yourself to avoid being caught between the tool or side handle and mE Alternating or Direct Current Type of Current walls or posts Should the socket or bit become bound in the work the reac dt tion torque of the tool could crush your hand or leg Earthing Terminal Grounding Terminal n Check to see that keys and adjusting wrenches
16. ects Battery pack terminals could be short circuited causing damage to the battery pack severe burns or fire The battery pack is Nickel Cadmium Ni Cad and is considered to be a toxic material by the Environmental Protection Agency Before disposing of damaged or worn out Ni Cad battery packs check with your State Environmental Protection Agency to find out about special restrictions on the disposal of these battery packs take them to your local recycling center for proper disposal or call 1 800 822 8837 CONTROLS AND COMPONENTS 1 Battery Pack 8 Forward Reversing and 2 Release Buttons on Each Side Trigger Lock Lever 3 120V AC Adapter 9 Variable Speed Controlled The battery is not fully charged Before first use the battery pack requires 4 Charger Trigger Switch 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 5 LED Charging Indicators 10 Accessory Bit Holder 2 hours for the battery to be fully charged 6 10mm 3 8 in Keyless Chuck 11 Comfort Rubber Grip Always switch to a fresh battery when tool performance begins to diminish 7 25 Adjustable Torque Settings ACCESSORIES Severe heat is most destructive to a battery the more heat generated the faster Control Ring 12 Double Ended Screwdriver Bits 2 the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not att
17. empt to discharge a tool s battery by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool COMPONENT MODEL NUMBER and recharge the battery for optimal performance pane ae Charge battery pack at ambient temperatures between 50 F 104 F CHARGER 690072 Store tool and battery pack in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells The battery pack should always be recharged when the Cordless Drill begins to run slowly 10mm 3 8 in KEYLESS CHUCK 690076 When battery pack is not in use keep it away from other metal objects such as paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause sparks burns or fire 9 10 REMOVING ATTACHING BATTERY PACK REMOVE BATTERY PACK 1 Press both release buttons on either side of the Cordless Drill to release the battery pack 2 Pull battery pack free of Cordless Drill ATTACH BATTERY PACK 1 Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Drill 2 Press the battery pack into place Make sure the latches are securely fastened Do not use the Cordless Drill if the battery pack is not seated properly RELEASE BUTTON 4 WARNING Before using battery charger please read carefully all
18. instructions and cautionary markings on battery charger battery pack and product using battery NOTE The charger will not automatically turn OFF when the battery pack is fully charged The charging indicator light will remain ON until the charger is disconnected from the electrical outlet CAUTION Remove battery pack from charger and disconnect charger from power after 5 hours of charging operation Overcharging can overheat bat tery cells and cause permanent damage to the battery pack and charger kit The battery pack and charger heat during charging Place the charger on a flat non flammable surface away from flammable materials with at least four inches of clearance to allow proper air circulation around the charger and battery pack When the battery pack requires recharging a 3 5 hour charge allows the tool to operate at full power A charging indicator light on the charger will illuminate to show that charging is taking place CHARGING BATTERY PACK CHARGE BATTERY PACK BATTERY PACK 1 Make sure the trigger on the Cordless Drill is in the OFF position and remove the battery pack from the Cordless Drill Plug 120V AC Adapter into household outlet and into side of battery charger Insert battery pack into battery charger When the battery is BATTERY placed in the charger the CHARGER red LED indicator light will remain on When fully charged reattach battery pack onto Cordless Drill making
19. is may damage your tool To reduce jamming always keep the Drill running when pulling the bit out of a finished hole 16 SCREWDRIVING Always use the correct type and size of screwdriver bit e f screws are difficult to tighten try applying a small amount of washing liquid or soap as a lubricant Always hold the tool and screwdriver bit in a straight line with the screw MAINTENANCE AND CLEANING WARNING Always remove the battery pack before attempting cleaning or maintenance NOTE This Cordless Drill is lubricated before it leaves the factory This lubrication should last for the life of the tool No further lubrication is required Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Always clean the battery pack using only a dry cloth Do not use liquids Always unplug the charger before cleaning it Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth Never open the Cordless Drill case battery pack or charger Do not attempt to repair the Cordless Drill battery pack or charger yourself Opening any of these parts will void your warranty Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always
20. laimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION 20 WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPER
21. moving the bit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory Accessories may be hot after prolonged use 14 T AY 1 Hold the rear end of the chuck in one hand and use the other hand to rotate the front end in LOOSEN 5 a counterclockwise direction to open the jaws of the chuck 5 TIGHTEN Z 2 Insert the shank of the bit or 1 other accessory fully into the HOLD a keyless chuck taking care to keep the bit in the center of the jaws of the chuck 3 Turn the front end of the chuck clockwise to hold the bit in place 4 Tighten securely by turning the front end of the chuck clockwise while holding the rear end WHEN DRIVING FASTENERS Always start slowly and gradually increase the speed of the Drill Release the trigger when you feel the clutch slip Always keep the driver bit straight to prevent damage to the screw Hold the Drill with both hands to ensure control if the bit should stick or slip To prevent wood from splitting drill pilot holes into the wood before driving in the screws DRILLING METAL WHEN DRILLING HARD METALS Apply a lubricant such as cutting oil to the tip of the bit Start with a small hole then enlarge to the required size Make sure the bit is actually cutting and not spinning in the hole as this will dull the edges of the bit Keep enough pressure on the bit to keep it drilling thr
22. ors ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock If operating a power tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI protected supply Use of an GFCI reduces the risk of electric shock PERSONAL SAFETY A WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Prevent accidental starting Be sure switch is in the locked or OFF position before connecting to power source and or battery pack picking up or carry ing the tool
23. oss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disc
24. ough the material DRILLING MASONRY WHEN DRILLING MASONRY Masonry can be brittle so be careful not to apply too much pressure and crack the material Apply enough pressure to keep the bit cutting and not spinning in the hole as this will dull the edges of the bit Bricks and similar soft materials will require less pressure concrete will require much more DRILLING WOOD Use twist bits to drill holes in wood Make sure the bits are sharp Pull the bits out of the hole frequently to clear chips from the flutes as an overburdened bit may overheat HINTS FOR OPTIMUM USE DRILLING Keep the right amount of pressure in a straight line with the drill bit Too little and the bit will spin without cutting too much and the motor may stall Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool This will prevent stalling and leave a cleaner hole Use a block of wood to back up work pieces that may splinter Use spade bits when drilling large diameter holes in wood Use HSS drill bits when drilling in metal Use masonry bits when drilling in soft masonry Use a lubricant when drilling metals other than cast iron aluminum copper and brass When drilling start the hole slowly allowing the bit to drill deep enough to prevent slipping at higher speeds Never try to start a stalled Drill by clicking the trigger switch ON and OFF Th
25. ponent thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insure
26. s Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 22
27. s Drills Screwdrivers Angle Grinders Impact Wrenches Reciprocating Saws Sanders Routers Jigsaws Rotary Tools Circular Saws Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 18 2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of two years from original date of purchase SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or com
28. th or serious injury DANGER WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A WARNING CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury 4 CAUTION CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS DANGER People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated ar
29. ty measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many acci dents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation BATTERY TOOL USE AND CARE A CAUTION Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other sm
Download Pdf Manuals
Related Search