Global Door Controls GAL-1180L-IC626 Installation Guide
Contents
1. the lever slightly and tighten screws securely INSIDE MOUNTING PLATE Align arrow mark to be positioned in latch MOUNTING SCREW b Place rose liner on mounting plate and tighten with screw securely INSIDE MOUNTING PLATE INSIDE ROSE LINER MOUNTING SCREW Align arrow mark to OUTSIDE MOUNTING CATCH TOOL LOCATION CATCH TOOL A OUTSIDE MOUNTING PLATE A OUTSIDE Install outside lever assembly LEVER on the door Make sure tail of ASSEMBLY latch engaging with retractor correctly as illustration left a Press rose onto rose liner Be sure to fit rose in recess of rose liner INSIDE ROSE LINER b Use lever catch to press down catch in the hole and push inside lever all the way in until clicks into catch hole INSIDE ROSE be positioned in latch TEMPLATE 3 gt lt 2 15 32 62 7mm FOLD HERE ON DOOR EDGE 5 32 4mm ech D 51 45 40 35 2 1 3 4 1 9 16 1 3 8 Std latch drill 25 4mm 1 Drive in latch drill MARK CENTER OF 2 2 1 8 54mm 32 HOLE ON DOOR FACE 24 5mm 31 32 hole at center of door edge EV1 T EV12. EV1 INSTALLATION INSTRUCTIONS COMMERCIAL KEY IN LEVER INSIDE ROSE LINER INSIDE LEVER INSIDE ROSE INSIDE MOUNTING PLATE ILLUSTRATIONS ARE SHOWN WITH ENTRY MODEL INSTALLATION IS SAME FOR PRIVACY AND PASSAGE MODEL AS WELL FOLLOW ALL STEPS FOR NEW INSTALLATION FOLLOW STEPS 3C 4C 5 6 7 8 9 FOR REPLACEMENT INSTALLATION AFTER REMOVAL OF OLD LOCK AND LATCH PLATE 1 MARK DOOR Start 38 from floor and mark center of door edge Select backset 2 3 8 or 2 3 4 and mark hole center on door face Mark two holes for screw post 5 16 8mm HOLE FOR SCREW POST NOTE BACKSET ON DOOR FACE MUST BE SAME AS BACKSET OF YOUR LOCK 3 INSTALL LATCH a Insert latch in hole and keep it parallel to door face Mark outline and remove latch b Chisel 1 8 3mm deep or until faceplate flush with door edge 4 INSTALL STRIKE 1 25 4mm HOLE 1 2 12 7mm DEEP CENTER LINE strike Drill 1 25 4mm hole 1 2 12 7mm deep at intersection of horizontal and vertical center lines a Close door to mark horizontal center line of strike 5 REMOVE INSIDE TRIM Use lever catch tool to depress lever catch visible under hole of inside lever shank and slide off inside lever INSIDE LEVER rose rose liner and mounting plate LEVER CATCH TOOL INSIDE ROSE EV1 OUTSIDE MOUNTING 2 1 8 54mm HOLE FOR LOCKSET EV1 FOR USE ON DOORS 1 3 8 2 35mm 51mm THICK TOOLS REQUIRED FOR NEW I
3. NSTALLATION 1 philips head screwdriver 1 2 1 8 54mm hole saw 1 1 25 4mm drill bit 1 5 16 8mm drill bit 1 chisel TOOLS REQUIRED FOR REPLACEMENT 1 philips head screwdriver LOCK BODY ASSEMBLY OUTSIDE ROSE RP OUTSIDE LEVER 2 DRILL HOLES Drill holes as marked NOTE DRILL 2 1 8 54mm HOLE FROM BOTH SIDES TO AVOID SPLITTING WOOD 1 OR 31 32 24 6mm OR 25 4mm HOLE FOR LATCH D c Insert latch and tighten screws NOTE LATCHBOLT BEVEL MUST FACE TO CLOSING DIRECTION b Measure one half of door thickness from door stop to mark vertical center line of c Cut out jamb 3 32 2 4mm deep or until strike flush with jamb Tighten screws securely INSIDE ROSE LINER OUTSIDE LEVER ASSEMBLY EV1 EV1 EV1 6 INSTALL REMOVABLE THRU BOLT SCREW POST a Disassemble outside mounting plate from outside rose plate b Make clearance between outside mounting plate and insert the removable thru bolt screw post into the cavities of outside mounting plate c Continuing the follow up instructions 7 ADJUST DOOR THICKNESS a Remove outside mounting plate toward cylindrical case b Put the catch tool into the allocated position of outside mounting plate as the illustrating bellow c Rotate outside mounting plate to required door thickness by using a catch tool 8 INSTALL OUTSIDE LEVER ASSEMBLY LOCK BODY ASSEMBLY a Place mounting plate on door face and turn up
Download Pdf Manuals
Related Search