Great Day LL12894F Instructions / Assembly
Contents
1. 46724 great day install ins qxd 8 7 03 1 49 PM Page 1 F ppg Great DNS TACLCATION INSI RUCI omnis Day Inc Oe AN aen Description Loading ATV Ramp Applications Varies by Model ATVs Cycles Mowers and other wheeled vehicles equipment Warranty 2 Years Contents Installation Safety Maintenance and Use Instruction 1 Portable Ramps Specifications by Model See page 2 2 Stabilizer Straps Part A55 The loading ramp is a convenient effective tool for helping you transport your equipment or ATVs A ramp is also a piece of equipment that must be respected and used in a cautious and well planned manner Please read this manual and follow its instructions WARNING Important carefully To emphasize special information the 5 A Indicates potential hazard that could symbol A and the words WARNING CAUTION result in death or injury A WARNING and NOTE have special meanings Pay special 2 attention to the messages highlighted by these CAUTION signal words CAUTION NOTE a a Indicates potential hazard that could NOTE Indicates special information to make result in vehicle damage maintenance easier or instructions clearer A WARNING e Improper use of this product could result in injury or death 1 DO NOT use the ramp if the ramp is damaged or without utilizing the stabilizer straps Preparation Prior to H 2 Adjust the width of the ramp so the wheeled Installation vehicle tires are centered on the ramp panels Use the clip2. up or down ramp with any cargo loaded on front or back or with more than 1 rider Riding on ramp with cargo or a passenger could cause the ATV to overturn 9 DO NOT ride equipment up or down ramp with ramp or vehicle on cross slope 6 Steep ramp angles increase risk of vehicle lip over on ramp You need 2 of ramp for every 1 of tailgate height for safe loading T DO NOT exceed the load capacity vehicle plus rider An overloaded ramp could collapse 8 DO NOT allow use by anyone under 16 years of age 9 DO NOT carry tools firearms or other hazardous items on vehicle or carry such items in a pocket backpack etc during loading or unloading Hazardous items include loaded firearms bows and arrows knives with blades exposed saws whether hand or power operated or items with sharp or narrow edges that could contact you 1 O DO NOT use this ramp if there is any ice snow mud or other slippery material on ramp or tires 1 1 DO NOT use this ramp during a thunderstorm or any weather condition that includes lightning 1 2 Ride vehicle slowly and carefully on the ramp Too much speed or improper braking can cause loss of control 1 3 Plywood can be inserted into specific models using the special plywood slot rail to provide a smooth loading surface Plywood is inserted through the bottom see photo on page 4 E 46724 great day install ins qxd 8 7 03 1 49 PM Page 4 F A a Great Day Inc Maintenance 1 Ins
3. ion e All models refer to the product labels attached to your ramp The model by Model size capacity weight limits and use WARNINGS are attached to each ramp Al Number dimensions provided are nominal measurements and not intended to be exact Model Weight Limit Rung Spacing Design Width Length 42715 1250 5 Bi Fold 42 x71 46715 1250 5 Bi Fold 46 x 71 48697 1250 7 Bi Fold 48 x 69 50697 1500 7 Tri Fold 50 x 69 46827 1250 7 Tri Fold 46 x 82 52765R 1250 5 Adj Small 42 x 52 x 76 60847R 1500 7 Adj Large 48 x 60 x 84 12894 1000 4 Arched 3 12 x 89 SAFETY TIPS amp WARNINGS e WEIGHT LIMITS are based on distributed weight loads A bi fold ramp rated at 1250 Ibs is limited to 625 Ibs per panel or side A tri fold 8 panel ramp rated at 1250 Ibs is limited to 625 Ibs per outer panel If using only 1 panel to load or unload on a multiple panel ramp the maximum weight limit is one half 1 2 the rated weight limit capacity of a ramp pair or as published for a single panel e TRAILER LOADING Follow the same instructions as loading a truck Straps must be secured to avoid push off 46724 great day install ins qxd 8 7 03 1 49 PM Page 3 F a S Great Day Inc 1 Put safety helmet on RN EEA Remove all cargo from the ATV or equipment being loaded Riding the 3 Keep the ATV in low range and or first gear and drive it SLOWLY onto the ramp Be sure that 4 Wheeled your ATV is centered on the loadi
4. ng camp and there is no overhang Vehicle or 4 Once on the ramp lean forward to maintain proper balance ATV up the 5 Slowly proceed up the ramp Once the ATV is in the truck bed apply the brakes to avoid Ramp contact between the ATV and the rear of the truck cab When parked apply the parking brake and secure the ATV to the truck bed with tie downs WARNING e Do not apply throttle while backing down ramp Riding the T Refer to PREPARATION PRIOR TO INSTALLATION and INSTALLATION sections and follow 4 Wheeled those directions before unloading Vehicle or 2 After the loading ramp is secured to the truck start the ATV and unlock the parking brake ATV down With the ATV in reverse begin slowly backing the ATV until it is to the point that it will free roll itself the Ramp down At this point only use the brakes to back slowly down the ramp 3 Once all four tires are on the ground you may then apply the throttle of your ATV A WARNING Safety Considerations e Failure to follow these safety considerations may result in injury or death 1 DO NOT use this ramp without first securing the ramp to the truck using the stabilizer straps Otherwise ramp could fall or pull away from tailgate 2 The vehicle must be narrower than the ramp A wider vehicle has increased risk of falling off the side 3 DO NOT ride any 3 wheeled vehicles two wheeled vehicles or cycles up or down this loading ramp 4 DO NOT ride ATV
5. pect ramp periodically for damage loose fasteners loose hinges and corrosion DO NOT use the ramp if the ramp is damaged in any manner 2 Lubricate the hinges and adjustable sleeves annually with a lightweight oil MODEL 46827 WITH CLOSED SURFACE DESIGN OPTION QTY ITEM BELONE 1 x 6 Drill Bit VERTICAL RAIL 6 2 No 10 Machine Screws Needed 6 Lock Washers 6 Nuts 1 Wrench 1 Screw Driver Plywood thickness 1 4 maximum Plywood Dimensions 13 746 X 76 1 4 1 On the second tread from the bottom of the ramp EEE drill two 346 holes thru plywood and tread The hole eon T OR ct erry location should be 1 4 from the inside of each vertical NOTE PLYWOOD AND HARDWARE rail channel and in the center of the tread ARE NOT INCLUDED 2 Now secure the plywood with the 2 No 10 machine screws lock washer and nut 3 Repeat step 1 and 2 for the remaining two panels For more information about this or other products contact us at Great Day Inc P O Box 472 Tallulah LA 71284 1 318 574 5003 1 866 645 1918 www greatdayinc com An IPM Enterprise E
6. s provided to lock the telescoping tubes together after adjustment This will help stabilize the ramp panels during loading Applies to adjustable models only 3 Make sure the engine of the truck onto which you are loading is turned off and the parking brake is set ok Place loading ramp on tailgate of truck with the holding fingers A resting on the tailgate as shown in Figure 1 Installation A WARNING e To maintain balance be sure the ramp is centered on the tailgate 2 Secure each side of ramp to the third or fourth tread B depending on the truck bed height as shown in Figure 1 by pulling the s hook and buckle around the tread through the loop at opposite end of strap as shown in Figure 2 Attach the s hook to the bumper Figure 3 and pull tight using the buckle to make adjustments and making sure the top tread C and fingers A of ramp is touching the tailgate as shown in Figure 1 E 46724 great day install ins qxd 8 7 03 1 49 PM Page 2 p Great Day Inc 3 Before riding a 4 wheeled ATV up or down this ramp be sure that you have read and understand the WARNINGS provided in the SAFETY CONSIDERATIONS section and read the warning label on the ramp itself A WARNING e Maximum weight limits includes combined weight of operator and vehicle e Do not ride up or down any GDI loading ramp with a 3 WHEELED ATV or any vehicle that exceeds recommended weight limits CAUTION Informat
Download Pdf Manuals
Related Search