IDEAL Security LSDXCR2267SN Installation Guide
Contents
1. CREW SELECTION DOOR THICKNESS 2 Over lay screws on top of the image Me NOR n 3 Select the screws that match your door thickness 1 1 2 TO 1 5 8 _ Now the deadbolt screws are selected and ready for installation 13 4 TO1 7 8 C tozi r PAGE 4 OF 5 HANDLE AND LATCH INSTALLATION 1 Arrange handle housing and backplate as shown 2 Place spindle amp spring in between housing amp backplate KEY LOCK SPINDLE 3 Place the outside handle assembly from step 1 amp 2 on door If your door thickness is not standard then The spindle should project through inside of door a max of 3 8 and min of 1 4 You may have to cut off spindle 4 Place the latch on inside of door fasten with two machine screws Do not over tighten screws Fasten the backplate with the tie down screw 5 Place the latch strike use shim if required on jamb aligning with the pilot holes on jamb fasten with two tapping screws HANDLE SPINDLE amp SPRING KEY LOCK amp DEADBOLT INSTALLATION Li D p 1 Insert the flat spindle into the back of key lock Ensure spindle bottoms into key lock If your door thickness is not standard then The spindle should project through inside of door a max of 1 and min of 3 4 Cut off the spindle beyond that length 2 Place key lock on outside of door 3 Place deadbolt on inside of door fasten with two machine screws Do not over tighten screws 4 Place the strike for deadbolt on jamb a2. LSDXCR2267 LATCH SET DX CR3 2260 357 RFQDXCR3 TEMPLATE AND INSTALLATION INSTRUCTIONS WARNING CHECK DOOR PROFILE PRIOR TO INSTALLATION You will require a profile wide enough for proper installation With the door closed the minimum inside door profile width is 1 3 4 from the edge of the door frame glass side to the edge of the door jamb or metal door frame z bar which ever is narrower The minimum outside door profile width is 2 1 8 from the edge of the door frame glass side to the edge of the door jamb or metal door frame Z bar which ever is narrower DETERMINE IF YOUR STORM DOOR IS HINGED RIGHT OR LEFT FOR PROPER USE OF DRILLING TEMPLATE From outside of door looking in if the hinges are on your left your door is left handed If the hinges are on the right it is a right handed door Ensure that the inside latch and deabolt do not interfere with the prime door lock PEAS eRe EEIE L aE TE TA ne RR T REDS SSR SMS O21 E E ee a 2 l 1 16 8 PLCS FO 1 5 32 v aI V P s m JAS LOogavad IMLS HOLWT 29 32 N YOO ONIMSLNO GNVH LHII YO INN GAYODS fo gt gt gt gt _ _ __ sh a Jals R 5 16 ii i 51 8 1 6 PLCS SIDE A SCORED LINE FOR LEFT HAND OUTSWING DOOR DEADBOLT STRIKE LATCH STRIKE PAGE 1 OF 5 TEMPLATE PLACEMENT AND DRILLING INSTRUCTION 1 Fold the template on the dotted line to 90 according to the handedness left or right 2 With the door in closed posit
3. ion place folded template on inside of door so that the SIDE A is against the jamb or metal z bar which ever projects out farther and SIDE B is on the inside surface of door 3 Use a center punch to mark the position of 6 holes on the inside surface of door on SIDE B Mark the position of 4 holes on the jamb on SIDE A for strikes 4 Using a 5 16 drill bit drill 6 holes straight through door from SIDE B 5 Using a 1 16 drill bit drill 4 pilot holes with depth of 1 on the jamb on SIDE A DAIS NOAA DETAIL A PAGE 2 OF 5 LSDXCR2267 HANDLE SPINDLE AND LATCH SCREW SELECTION INSTRUCTION 1 Print out this sheet using 1 1 scale verify using a ruler against the print out image below 2 Measure door thickness 3 Over lay spindles and screws on top of the image below 4 Select the spindle and screws that match your door thickness DOOR THICKNESS SPINDLE SCREW 1 TO 1 1 8 E 1 1 4 TO 1 3 8 E m 1 1 2 TO 1 5 8 1 3 4 TO 1 7 8 2 TO 2 1 4 Now that the handle spindle and latch screws are selected and ready for installation PAGE 3 OF 5 LSDXCR2267 KEYLOCK SPINDLE AND DEADBOLT SCREW SELECTION INSTRUCTION KEY LOCK SPINDLE PREPARATION 1 2 3 4 Now the key lock spindle is ready for installation Print this sheet using 1 1 scale Over lay flat spindle against the image Mark door thickness on the spindle Cut off at the mark line DEADBOLT S
4. lign with pilot holes on jamb fasten with two tapping screws S 9 MAX 3 8 MIN 1 4 ee crm MIN 3 4 9 Handle Spindle Projected Length Deadbolt Spindle Projected Length PAGE 5 OF 5 X Vy WV TIE DOWN SCREW DEADBOLT STRIKE DEADBOLT Thank you for your purchase If you require any information or installation assistance please contact our customer service Monday to Friday 7 30 am 3 pm Eastern Time Tel 1 800 361 2236 x 230 e mail info idealinc com Updated instructions if applicable can be found at www idealinc com IDEAL SECURITY INC LASALLE QUEBEC CANADA CORAOPOLIS PA USA
Download Pdf Manuals
Related Search