SPEEDWAY 7296 Use and Care Manual
Contents
1. Any failures made in following the safety regulations and instructions result in an electric shock fire and or serious injury Keep all instructions and manuals in a safe place for tuture use or reference SAFETY INSTRUCTIONS 1 Before using the tool check for damaged parts if any part of the tank appears damaged itshould be carefully checked to determine thatit will operate perform property 2 Never exceed the maximum pressure of 125 PSL Over pressurizing the air tank could resultin an explosion 3 BURST HAZARD Do not fill from any compressed gas cylinder or system charged with more than 150 PSI 4 Pull the Safety Release valve ring prior to operation to ensure that the valve is functioning properlyand to clear the valve of any possible obstructions 5 Do notover inflate objects Never exceed the maximum pressure rating of any inflatable 6 Do not leave the air tank unattended while itis in use 7 Only ill the tank with alr from a service station or low pressure air compressor system 8 Do 11 the tank with gas or anyother flammable substances under any circumstances 9 Always wear proper safety protection when using this product Safety goggles must always be during use 10 Keep away from moisture orheat radiation Store the For warranty purchas please keep your dated proof of purchase le or alah to the manual for safekeeping2. For customer service cat 1 800 348 5004 or ema feedbacknatiiools com 9807296 07 10 tank indoors to prevent unnecessary damage 11 Never use this tank as portable breathing device nor to dispense liquids Itis only used for inflating tires inflatables FAMILIARIZING WITH YOUR AIR TANK 1 ON OFF adjustment wheel 2 Fill inlet 3 Safety pressure release valve 4 Pressure gauge FILLING UP YOUR AIR TANK The ideal pressure for your tank is from 85 125 PSI Read the pressure gauge to determine whether the tank needs to be refilled Ifit does need to be refilled follow these instructions 1 Find an air refilling source The source should provide clean dry compressed air A full service gas station or mechanic shop are preferable The pressure found ata convenience store quick stop type of station usuallyis not enough to refill your tank 2 Fill he tank in the same way you would a car tire Plug the air Chuck from the source to the Fill Inlet on your tank The air should begin to flow immediately and you should see the gauge needle going up 3 Remove the air source s chuck from the Fill Inlet when the needle reaches 85 125 PSI USING YOUR AIR TANK refer to the Air Tank Fill Capacity Chart to determine the necessary air capacity 1 Tum the ON OFF air adjustment wheel counterclockwise open position So that the air may flow from the tank to the hose 2 A
3. Please carefully read and save these instructions before attempting to assemble maintain install or operate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage andor personal injury Please keep instructions for future reference Important Operating Instruction 5 GALLON AIR TANK Models 7296 CALIFORNIA PROPOSITION 65 WARNING You can create dust when you cut sand drill grind materials such as wood paint metal concrete cement or other masonry This dust often contains chemicals known to cause cancer birth defects or other reproductive harm Wear protective gear WARNING This product its power cord may contain chemicals Including lead known to the State of California to cause cancer and birth defects other reproductive harm Wash hands after handling Important When using equipment few safety precautions must be observed to avoid Injuries and damage Please read the complete operating manual with due Keep this manual in a safe place so that the information is available at all times Ifyou give the equipmentto any other person give them these operating instructions as well We accept no liability for damage or accidents which arise due to non observance of these Instructions and the safety Information herein CAUTION Read all safety instructions
4. o persons or property or for incidental special or consequential damages arising from the use of our products To receive service under warranty the original manufacturer part must be retumed for examination by an authorized service center Shipping and handling charges may apply Ifa defect is found NAT will either repair or replace the product at its discretion DO NOT RETURN TO STORE For Customer Service Email feedback natitools com or Call 1 800 348 5004 Teodbacktinatitols com 4 800 348 5004 5 GALLON AIR TANK Tara Bypass Vawe Some 2 Ae Hone 1 Pressure Fa Ser Dal 9807296 08 10
5. ttach the tank s air chuck to the fil inlet of your tire until it reaches the desired maximum pressure 3 After using the tank make Sure to turn the ON OFF al adjustment wheel clockwise to avoid possible leaks DISASSEMBLING AND REPAIRING YOUR AIR TANK ithe tank needs disassembled and repaired you will need 9 16 Open end wrench Adjustable wrench Teflon Tape 1 Completely empty your pulling the ring on the safety pressure release valve until the ik by pressure gauge indicates zero and air fow stops 2 Using a 9 16 open end wrench remove the hose from the manifold 3 Remove the gauge from the tank using an adjustable wrench 4 You can now remove the manifold from the tank using an adjustable wrench reassemble make sure to apply Teflon tape on all threads follow this procedure backwards eedback inatitls com 4 800 348 5004 Limited Manufacturer Warranty North American Too Industries makes every effort to ensure that this product meets high quality and durability standards NAT warrants to the original retail consumer a 1 year limited Warranty from the date the product was purchased at retail and each product is free from defects in materials Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NAT shall in no event be liable for death injuries t
Download Pdf Manuals
Related Search