Chimney Free 34HF600GRA Installation Guide
Contents
1. 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Modifications not approved by the party responsible for compliance could void user s authority to oper ate the equipment This Class B digital apparatus complies with Canadian ICES 003 Note please operate remote transmitter at a slow measured pace Press the remote control buttons with an even motion and gentle pressure Repeatedly pressing buttons in rapid succession may cause the transmitter to Malfunction REPLACING THE REMOTE CONTROL BATTERY When the remote control stops operating or its range seems reduced it is time to replace the batteries with new ones Remove the batteries if the remote control won t be used for a long period of time 1 The battery compartment is located on the back end of the remote 2 Press the small tab inward as you slide the battery door open and remove the old batteries 3 Replace with 2 AAA batteries not included making sure the and sides of the battery match the inside of the battery compartment 4 Replace the battery door Note Do not mix old and new batteries Do not mix alkaline standard carbonzinc or rechargeable nicad nimh etc batteries DISPOSAL OF USED BATTERIES Batteries may contain hazardous substances which could be endangering to the enviroment and to human health This symbol marked on the bat2. Watts A IMPORTANT INFORMATION Please read and understand this entire manual before attempting to assemble operate or install the product If you have any question regarding the product please call customer service at 1 877 888 8225 9 a m 5 p m EST Monday Friday When using electrical appliances always follow basic precautions to reduce the risk of fire electrical shock and injury to persons including the following 1 Read all instructions before using this appliance 2 This appliance is hot when in use To avoid burns do not touch hot surfaces with bare skin If provided use handles when moving this appliance Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft from the front of this appliance WARNING In order to avoid overheating do not cover the heater AA WARNING Use extreme caution when operating heater near children and the disabled 3 The appliance is not to be used by children or persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction 4 This appliance is not a toy Supervise children playing near it If possible always unplug this appliance when not in use 6 Do not operate any heater with a damaged cord or plug after the appliance malfunctions or if it has been dropped or damaged in any manner 7 Ifthe supply cord is damaged it must be replaced by
3. 2 F or 17 C 27 C or always ON This button on the remote control only turns ON and OFF heater function NOTE To change between F and C press and hold the HEATER button on the control panel for 10 seconds x TIMER Press the TIMER button will cycle through the 10 timer settings 30 minutes 1 Hour 2H 3H 4H 5H 6H 7H 8H and 9H and the OFF setting BACKLIGHT Press the backlight button will turn on and off backlight effects NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions
4. 26 P01 Remote Control 5 Buttons 1 D No 6 ppc 9
5. ITEM 0385776 styleselections WALL HANGING Style Selections is a registered ELECTRIC Fl REPLAC E tradmark of LF LLC All rights reserved MODEL 34HF600GRA Francais p 14 Espa ol p 27 nati 7 P _ g nA AAA gt A AAA 2 ee A E t SE a SS eT E O9 a EE eee AR A cy 3 T A eneo Y Y AK AMA 3C yc X A Y CY i Eee A A 4 sI I I a i ey Questions problems missing parts Before returning to your retailer call our customer service department at 1 877 888 8225 8 a m 8 p m EST Monday Friday TABLE OF CONTENTS Prod ct SpecificatioNS ceu de feces sea cde pete peut es a d Meu a deua s mee d t eM 2 Important Information era iti deae ritu ce P tud ttu Ded utes ei aa o t i n eed a M t b eda e P ut Duet 3 Package Contents greet uses eae ped dos o opted ira rn rino ie Aaa 5 Hardware Coments xcu nire rom adii nde indice id rd ote ce nu e Lee 5 A S PRPRTERS 6 Installation Instr cllorns osea oor S A ris ptite quieta 6 Operating InslF cBofls ene tai bae do qnt iode me be ortae t gat teta Fx vi bun eod lau doe eto uta 9 Care and Maintenance ccocooiinninnnnnniinnaiicici en 11 A 11 Waranty asocia tete pon arat aces Padget wing ATA E AA Rods Cen e Dp e vec Tan orte PobeE y 12 Replacement Parts did oo dao d ctia b cx A AS ASA Die Ix dde de 13 PRODUCT SPECIFICATIONS VOLTAGE 120 V 60 Hz AMPS 12 5 Amps WATTS 1500
6. UCTIONS This appliance can be operated by both remote control and manual button Once the unit has been properly connected to an earthed electrical outlet turn on the main power switch located on the left hand side of the appliance A beep should be heard when the power is first applied CAUTION The unit power cord must be connected to a properly grounded and protected 120V outlet Always use ground fault protection where required by the electrical code Do not operate the unit if it is damaged or has malfunctioned If you suspect the unit is damaged please call a qualified service technician to inspect and to replace any part of the electrical system if necessary NOTE To use both remote control and manual functions the main power switch must be in ON position b POWER The POWER button supplies power to all of the functions of the fireplace The POWER button will put the insert in a standby mode This will turn off all functions at once but will hold the settings in the memory By pressing the POWER button again the unit will turn on at the same settings NOTE Holding the POWER button on the control panel for 10 second will disable the heater function Q FLAME Each time the flame button is pressed the intensity of the flame decreases There are 6 brightness levels you can cycle through and the OFF setting HEATER Your fireplace consists of a fan forced wire element type heater The thermostat setting range is 62 F 8
7. cluding the risk of any direct indirect or consequential loss or damage arising out of the use or inability to use the product except as provided by law 7 All other warranties expressed or implied with respect to the product its components and accessories or any obligations liabilities on the part of the manufacturer are hereby expressly excluded 8 The manufacturer neither assumes nor authorizes any third party to assume on its behalf any other liabilities with respect to the sale of the product 9 The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product This warranty is void if a The fireplace is subjected to prolonged periods of dampness or condensation b There is any unauthorized alteration willful abuse accident or misuse of the product c You do not have the original receipt of purchase IF WARRANTY SERVICE IS NEEDED Contact the manufacturer at www twinstarhome com or call our customer service department at 1 877 888 8225 9 a m 5 p m EST Monday Friday Make sure you have your warranty your sales receipt location of purchase and the model serial number of your product 12 REPLACEMENT PARTS LIST AND EXPLODED VIEW For replacement parts call our customer service department at 1 877 888 8225 9 a m 5 p m EST Monday Friday Flame PCBA Y12 S84 P40 Flame Generator Spinner Y12 S84 P11 Blower Heater Assembly Y07 C
8. ected to a permanent ground such as a properly gounnded outlet box The adapter should not be used if a three slot grounded receptacle is available Cover Of Grounded Outlet Box Metal Screws Grounding Pin Adapter use SAVE TH ESE Grounding G INSTRUCTIONS Pin Fig 1 PACKAGE CONTENTS Quantity Mounting Bracket B Wall Hanging Fireplace Bottom Bracket ET S Bottom Base Remote Control HARDWARE CONTENTS Picture Part Description Quantity Shown to size Screw 4 0 2 in x 1 5 in Wall Plug 0 3 in x 1 5 in 4 Screw cc 1 4 in x 0 7 in 4 DD Screw 4 1 4 in x 0 5 in PREPARATION Before beginning installation of product make sure all parts are present Compare parts with package contents list and diagram above If any part is missing or damaged do not attempt to assemble install or operate the product Contact customer service for replacement parts Estimated Assembly Time 15 minutes Tools Required for Assembly not included Phillips screwdriver Drill Hammer been under water Immediately call a qualified service technician to inspect and to replace any part of the electrical system if necessary Keep plastic wrapping away from children Open the packaging carefully and remove the foam Remove and discard the plastic bag Be responsible when handling the packing materials Keep the original packaging for future transport a
9. le regulations to reduce the risk of fire electrical shock and injury to persons WARNING Do not use this fireplace if any part of it has been under water Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electrical shock or personal injury WARNING During any service of this appliance the power to the unit must be turned off First turn the main power switch to the OFF position Then remove the electrical plug from the wall outlet TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION No power Power cord was not Check that unit is plugged into a standard plugged in the outlet 120V outlet Main power switch is in ON Spinner motor doesn t Open the front panel and place in a safe position but no flame effect work position and check if the spinner motor was working Have flame effect but Heater or blower Try to turn on off heater button several times heater does not blow warm air doesn t work to make sure it is at ON position and the indicator light should light up at the same time Heater doesn t work but The product is on the Turn all switches to the OFF position and power and heater switches protected status unplug the unit from the wall outlet for 5 are in the ON position minutes After 5 minutes plug the uni
10. nd or storage Check that all accessories are removed before you discard the packing WARNING Do not use this electric fireplace if any part has LOCATING YOUR ELECTRIC FIREPLACE Your new electric fireplace may be installed virtually anywhere in your home However when choosing a location ensure that the general instructions are followed For best results install out of direct sunlight Power supply service must be either completed or placed within the electric fireplace prior to finishing to avoid reconstruction WARNING Keep drapery and other furnishings p f at least 3 ft from the front and sides of the p min 2 electric fireplace LY di Clearance to combustibles Y cp 2 Wie min 2 imm POO pAr EE PESEE EAEE 2 in d gt Pi eee 2 in E 50 mm zb Wee DH 0 in 2 min 2 in FLOOR INSTALLATION INSTRUCTIONS 1 Remove mounting bracket A from back of Fireplace B by removing the two screws at the top back of the unit Choose a solid wall surface to attach the mounting bracket A Position the mounting bracket A in the desired location and mark the four holes with a pencil Fig 1 INSTALLATION INSTRUCTIONS 2 Drill 4 holes 0 32 in in the wall Insert the wall anchors BB into the holes using a hammer Fig 2 Hardware Used Wall Plug UM d 03inxi5in gt x4 3 Attach the mounting bracket A to the wall fastening the 4 screws AA into
11. rfaces like a bed where opening may become blocked 19 This appliance has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable liquids are used or stored This fireplace should not be used as a drying rack for clothing Do not hang Christmas stockings or other decorations on or near this product 20 Use this appliance only as described in the manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons e 21 There is a thermostat limiter inside the heater When the inner temperature overheating or abnormal heating occurs the thermostat protective device will cutoff the power supply to avoid damage to the fireplace or risk of fire A IMPORTANT INFORMATION 22 Avoid the use of an extension cord because the extension cord may overheat and cause risk of fire However if you have to use an extension cord the cord must be No 14 AWG minimum size and rated not less than 1875 watts The extension cord must be a three wire cord with grounding type plug and cord connection The extension cord shall not be more than 20 ft in length 23 See directions in Figure 1 This heater is for use on 120 volts The cord has a plug as shown in figure 1 See Figure 1 for grounding instruction An adapter as shown at C is available for connecting three blade grounding type plugs to two slot receptacles The green grounding plug extending from the adapter must be conn
12. t back into wall outlet and operate as normal 11 1 YEAR LIMITED WARRANTY The manufacturer warrants that your new electric fireplace is free from manufacturing and material defects for a period of one year from date of purchase subject to the following conditions and limitations 1 Install and operate this electric fireplace in accordance with the installation and operating instructions furnished with the product at all times Any unauthorized repair alteration willful abuse accident or misuse of the product shall nullify this warranty 2 This warranty is non transferable and is made to the original owner provided that the purchase was made through an authorized supplier of the product 3 The warranty is limited to the repair or replacement of part s found to be defective in material or workmanship provided that such part s have been subjected to normal conditions of use and service after said defect is confirmed by the manufacturer s inspection 4 The manufacturer may at its discretion fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part s 5 Any installation labor construction transportation or other related costs expenses arising from defective part s repair replacement or otherwise of same will not be covered by this warranty nor shall the manufacturer assume responsibility for same 6 The owner user assumes all other risks if any in
13. tery and or packaging indicates that used battery shall not be treated as municipal waste Instead it shall be left at the appropriate collection point for recycling By ensuring used batteries are disposed of correctly you will help to prevent potential negative consequences for the environment and human health The recycling of materials will help to conserve natural resources For more information about collection and recycling of used batteries please contact your local municipality or your waste disposal service 10 CARE AND MAINTENANCE CLEARANCE TO COMBUSTIBLES Keep electrical cords drapery furniture and other combustibles at least 3 ft from the front of the heater and away from the sides CLEANING TRIM Clean the metal trim using a soft cloth slightly dampened with a citrus oil based product and buff with a clean soft cloth Do not use brass polish or household cleaners as these products will damage the metal trim Citrus oil based products can be obtained at supermarkets or hardware stores WARNING Make sure the power is turned off before proceeding Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes If repairing or replacing any electrical component or wiring the original wire routing color coding and securing locations must be followed WARNING Electrical outlet wiring must comply with local building codes and other applicab
14. the manufacturer its service agent or similarly qualified persons in order to avoid a hazard 8 Only a qualified service person should repair this product 9 Under no circumstances should this fireplace be modified Parts having to be removed for servicing must be replaced prior to operating this fireplace again 10 Do not use outdoors 11 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate this appliance where it may fall into a bathtub or other water container 12 Do not run cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic areas and where it will not be tripped over 13 To disconnect this appliance turn controls to the off position and then remove plug from outlet 14 Connect to properly grounded outlets only 15 This appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the current CSA C22 1 Canadian Electrical Code or for U S A installations follow local codes and the National Electrical Code ANSI NFPA NO 70 16 The heater must not be located immediately below a socket outlet 17 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the appliance 18 To prevent a possible fire do not block air intakes or exhaust in any manner Do not use on soft su
15. the wall anchors Fig 3 Hardware Used Screw 0 2 in x 1 5 in ium 4 Hang the wall hanging fireplace B on the hooks at bottom and push the wall hanging fireplace B into mounting bracket A Re fasten the two screws removed in Step 1 Fig 4 STAND BASE INSTALLATION INSTRUCTIONS 1 Use 4 screws to fasten the stand C to the stand base D Fig 5 Screw 1 4 in x 0 7 in CR ii 2 Mount main body to the stand base Fig 6 3 Insert the stand bracket to the main body and fasten with 1 screw Fig 6 Screw 1 4 in x 0 5 in 0 xL exterior wall or chase the outer walls must be insulated to conform to applicable insulation codes T Cold climate installation recommendation When installing this unit against a non insulated ELECTRICAL CONNECTION A 15 AMP 120 Volt 60 Hz circuit with a properly grounded outlet is required Preferably the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation The unit comes standard with 6 ft three prong cord exiting from the rear of the fireplace Plan the installation to avoid the use of an extension cord If an extension cord must be used it must be a minimum 14 AWG three wire with grounding type plug connector and rated not less than 1875 watts The cord shall not be more than 20 ft in length OPERATING INSTR
Download Pdf Manuals
Related Search