Home Decorators Collection WSFP46ECHD-6 Instructions / Assembly
Contents
1. The front moldings face inward Back view Assembly continued 1 5 Attaching the cam bolts Cae oe 7 s ta 7 A A 1 6 Attaching the top panel 11 Back view Securely screw six cam bolts BB into the designated small holes on the top panel A by a Phillips screwdriver Insert five wood dowels CC into the top inner holes on upper side panels F and partition panel E Position the top panel A onto the inserted wood dowels CC and fasten it in place with six cam locks AA HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 1 T Attaching the back panels Pick up the upper back panel D and align the pre drilled holes against the upper long edge with the pilot holes on the back stretcher of top panel A Attach the back panel D in place using the provided washer head screws FF Align and attach two lower back panels H to the lower side panels and lower partition panels I J K and L with the provided washer head screws FF aN oy lt A xe g sl 4 gt 5 Y p AA Y D l ze TP gt l an Y Ne I Y H Y ow gt gt Y S4 uada eg ag FF gt LI iii i 1 8 Assembling the adjustable shelves Insert four shelf pins KK into the2. 1 P Middle crossbar 1 E Upper partition panel 1 Q Bottom panel molding 1 F Upper side panel 2 R Bun Foot 2 G Upper side panel molding 2 S Center support 1 H Lower back panel 2 T Left foot support 1 Left lower side panel 1 U Right foot support 1 J Left lower partition panel 1 V Firebox support 1 K Right lower partition panel 1 Fireplace insert 1 L Right lower side panel 1 Remote control with battery 1 3 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly 1 Attaching the cam bolts NOTE Do not fully tighten all bolts until you finish assembling all parts Once assembled go back and fully tighten all bolts This will make the assembly easier Unpack the unit and confirm that you have all the hardware and required parts Assembly the unit on a carpeted floor or the empty carton to avoid any scratch Securely screw seven cam bolts BB into the designated small holes on the lower side panels I and L and bottom panel molding Q Fully tighten with a Phillips screwdriver i EA 0 Qo in X i p nEn GE AS L am n Q 2 Attaching the bottom panel Insert four wood dowels CC into the inner holes of bottom panel C using four cam locks AA as shown at both ends and attach it between the lower side panels 1 and L by The cam lock assembling guide The pilot holes fo
3. ages CLEANING THE FIREPLACE TRIM Clean the metal trim using a soft cloth slightly dampened with citrus oil based product and buff with a clean soft cloth DO NOT use brass polish or household cleaners as these products will damage the metal trim Citrus oil based products can be obtained at supermarkets or hardware stores 17 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS Retain this manual for future use
4. DEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 25 Installing the tipping restraint hardware NOTE Young children can be seriously injured by tipping furniture You must install the tipping restraint hardware with the unit to prevent the unit from tipping causing any accidents or damage The tipping restraints are intended only as a deterrent they are not a substitute for proper adult supervision The tipping restraints are not earthquake restraints If you wish to add the extra security of earthquake restraints they must be purchased and installed separately Ask for assistance to position the assembled fireplace at the desired location against a wall In case of uneven floor floor levelers are provided at the bottom of the mantel If necessary adjust the floor levelers by hand to correct tilting until the unit is level Follow the instructions printed on the plastic bag containing the tipping hardware to attach the tip over restraint to the unit and the wall Connect the fireplace to the power transformer Follow the operating manual for the electric fireplace insert to control your fireplace Se s Wall Metal Bracket NS as Long Screw N 16 Care and Maintenance A Touch up Pen has been provided to repair any sma
5. HOME inmsa DECORATORS Model WSFP46ECHD 6 COL LECT LON ASSEMBLY INSTRUCTIONS Ashurst 46 inch Media Console Infrared Electric Fireplace in Anthracite Finish Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 6 p m EST Monday Friday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this fireplace console We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home improvement needs Thank you for choosing Home Decorators Collection Table of Contents Table of Content ccccsceecesesceeeeeeseeneeseecenensseeeees 2 Hardware Included Safety Information PTET Pee TECE CET r Terre Peeree eer re eer cree rere errr rer 2 Package Contents Warranty ice csccscsvecceesiececnnect ceceetegeedceetdecteenedhcvdvacescoeauegeteve 2 A SSO Y sede cca A E E E 4 Pre Assembly sagassuadasnoudusndncussdegesduusise cosdzest sesdudse soedsege ses 2 Care amd Maintena it lt sioa a a S 17 Planning Assembly cancnroisiossrinii neces 2 TOOIS required i miin a a 2 Safety Information Please read and understand these instructions before assembling and using this console Sa
6. ach the middle crossbar P to the center shelf B by using two wood dowels CC and three cam locks AA N Cam locks face inward de AA I SSG Gee Te u Ee c cer d l 8 Attaching the partition panel molding Fasten one lower partition panel molding O to the left lower partition panel J using two wood dowels CC and two cam locks AA Repeat the same procedure to combine the other lower partition panel molding O and right lower partition panel K together The outer edges are flush The outer edges are flush CC CC 7 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued Q Attaching the lower partition panels Insert four wood dowels CC into the inner holes of both lower partition panels J and K and attach them to the bottom panel C by using four long screws DD i Sa The moldings face inward K CC T A cC E 1 0 Attaching the center shelf o Insert eight wood dowels CC into the top inner holes of the lower side panels and lower partition panels I J K and L Ask for assistance to position the center shelf B onto the inserted wood dowels CC Attach the center shelf B in place by engaging eight cam locks AA The middle crossbar faces foward LE KX amp Z SS e S i K P A ee 5 As N ie a DAN D G Y 9 am
7. holes at your desired height inside each side compartment Tilt and install the adjustable shelves M onto the shelf pins KK ae r KK p pi O Y ARC M i M M Ip Assembly continued 1 Q Installing the door hinges Extend the door hinges PP and rest the hinge cups onto the cutouts of one door panel N Secure the door hinges PP in place by using two zinc screws GG in each Attach one knob LL to the front side of the door N with one knob bolt MM Repeat the same procedure with the other door panel N GG 20 Attaching the door panels o Pick up one door panel N and fasten the hinge bases to the left lower side panel I with four zinc screws GG in each Tighten the screws with the provided Phillips head L Key DO NOT fully tighten the screws Repeat the same procedure to attach the other door N to the right lower side panel L Open and close the doors to make sure they are aligned and shut correctly If necessary adjust the screws for a good fit Refer to the hinge sticker on door for adjustment 13 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 2 1 Attaching the rubber bumpers and cam lock covers Plug the cam lock covers JJ onto the v
8. isible cams locks to conceal the cams Stick the rubber bumpers NN on the outer corners of doors N as shown SSS Q JJ N 22 Installing the fireplace insert Lift the fireplace insert carefully into the back of the assembled mantel and center it in the opening DO NOT drag the insert across the bottom panel C as it may scratch the unit oss n SA l Electric C b Sh Firebox Nol a Assembly continued 23 Attaching the firebox support Align and attach the firebox support V to the bottom panel C by screwing two large screws HH into the countersunk holes The countersunk holes face upward sot Ne 24 Attaching the acrylic stopper A NOTE You must install the Acrylic TV Stopper to prevent TV from tipping when placing your flat panel television on the table top Remove the paper backing of acrylic stopper OO then properly align the acrylic stopper into the cut out on the acrylic stopper template on the front of the top panel A Press down on the acrylic stopper to help adhesion At the back of the top panel A carefully unscrew the two thumb tacks to remove the acrylic stopper template OO E y OO V4 A a4 E E 15 HOME
9. ll nicks or scratches that may occur during assembly or shipping To clean and care for your furniture Use a soft clean cloth that will not scratch the surface when dusting Use of furniture polishes is not necessary Should you choose to use polishes test first in an inconspicuous area Using solvents of any kind on your furniture may damage the finish Never use water to clean your furniture as it may cause damage to the finish Always use coasters under beverage glasses and flowerpots Liquid spills should be removed immediately Using a soft clean cloth blot the spill gently Avoid rubbing Always use protective pads under hot dishes and plates Heat can cause chemical changes that may create spotting within the furniture finish Stains or marks from crayons or ink markers will be difficult to remove In the event that your furniture is stained or otherwise damaged during use we recommend that you call a professional to repair your furniture Check bolts screws periodically and tighten them if necessary CARING FOR WOOD FURNITURE It is best to keep your furniture in a climate controlled environment Extreme temperature and humidity changes can cause fading warping shrinking and splitting of wood It is advised to keep furniture away from direct sunlight as sun may damage the finish Proper care and cleaning at home will extend the life of your purchase Following these important and helpful tips will enhance your furniture as it
10. p gt AA na I Assembly continued 1 1 Fastening the middle crossbar Stand the assembled unit upright Fasten the middle crossbar P to both partition panel moldings O by attaching two metal brackets II at the joints using two black screws EE per metal bracket As shown EE Countersunk holes Back view 1 2 Attaching the cam bolts Securely screw six cam bolts BB into the designated small holes on the center shelf B by a Phillips screwdriver EE EE Er a E 9 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 1 3 Attaching the upper side panel moldings Securely screw two cam bolts BB into the designated small holes on one upper side panel molding G by a phillips screwdriver Fasten the upper side panel molding G to one upper side panel F using one wood dowel CC and two cam locks AA As shown Repeat the same procedure to combine the other upper side panel and upper side panel molding F and G together xX 2 The outer edges are flush 1 4 Assembling the upper side panels and partition panel Insert the wood dowels CC into the inner holes of the upper side par F and partition panel E and attach them to the center shelf B by using six cam locks AA
11. r foot L 2 supports face forward l N The cam locks face the bottom of unit Assembly continued 3 Attaching the bottom panel molding Align and attach the bottom panel molding Q to the bottom panel C by using four wood dowels CC and three cam locks AA The bevel profile faces upward 4 Attaching the foot support Align and attach the foot supports T and U to the bottom panel C with two wood dowels CC and three short screws SS in each using the pilot holes as a guide A YX ee Ss The female connectors face outward A T i and point towards the front corners 5 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued D Installing the center support and bun feet Tightly screw the center support S into the threaded insert on the bottom panel C Screw two bun feet R into the female connectors on the foot supports T and U 6 Attaching the cam bolts Securely screw the cam bolts BB into the designated small holes on the center shelf B and the lower partition panel moldings O Fully tighten with a Phillips screwdriver Ts i i oA Roa B ri l l I rif l i i L U i x l a l i l 2 S O i O Assembly continued T Attaching the middle crossbar Align and att
12. t appears missing or damaged do not assemble this product and contact the Customer Service Team at 1 800 986 3460 TOOLS REQUIRED Phillips head Philips Here screwdriver provided j not provided Pre Assembly continued HARDWARE INCLUDED A NOTE Hardware not shown to actual size AA BB CC DD __EE FF GG HH ll dJJ KK LL MM NN 00 amp 7 PP QQ RR SsS LTT UU Part Description Quantity Part Description Quantity AA Cam lock 38 1 extra LL Knob 2 BB Cam bolt 38 1 extra MM Knob bolt 2 CC Wood dowel 42 2 extra NN Rubber bumper 4 1 extra DD Long screw 4 1 extra OO Acrylic stopper 1 EE Black screw 4 1 extra PP Hinge 4 FF Washer head screw 36 1 extra QQ Glue 1 GG Zinc screw 24 1 extra RR Touch up pen 1 HH Large screw 2 1 extra SS Short screw 6 1 extra II Metal bracket 2 TT Phillips head L Key 1 JJ Cam lock cover 28 1 extra UU Tipping restraint hardware kit 2 KK Shelf pin 8 1 extra PACKAGE CONTENTS _ e p _ N O l an 00 aa B H J Mi L a SSS M i C eA oc P R sj t uma ve F Q Part Description Quantity Part Description Quantity A Top panel 1 M Adjustable shelf 2 B Center shelf 1 N Door 2 C Bottom panel 1 O Lower partition panel molding 2 D Upper back panel
13. ve these instructions for future reference 9 Fits up to most 142 2 cm 56 in flat panel TVs Maxi load 61 2 kg 135 Ib MAXIMUM RECOMMENDED WEIGHT LOADS ESRR J WARNING This unit is not intended for use with CRT TVs Use only with flat panel TVs and audio video equipment meeting recommended size and weight limits Never use with larger heavier f than recommended flat panel TVs or equipment To avoid Place TV behind the stopper instability place flat pane TV in the centre of the unit the base of r A the television must be able to rest on the supporting surface of the unit without over hanging the edges Improperly ze positioned flat panel TVs or flat panel TVs or other equipment that exceed recommended size and weight limits could fall off or break the unit causing possible serious injury Maximum load 22 7 kg 50 Ib Warranty 7 We are confident that you will be delighted with this purchase Should this product be defective in workmanship or materials or fail under normal use we will repair or replace it for a period of up to one 1 year from date of purchase This warranty gives you specific rights and you may also have other rights which vary from state to state Contact the Customer Service Team at 1 800 986 3460 or visit www HomeDepot com homedecorators Pre Assembly PLANNING ASSEMBLY Compare all parts with the Hardware Included and Package Contents list If any par
Download Pdf Manuals
Related Search