Emberglow CCF18NG Instructions / Assembly
Contents
1. Coane PROC nC mC nC TCS 91 ime iN WRI i N 4 1 Rif 1 1 2 sy i N SAM NMEN MENN ONS NN mM MENN 1 HH NY oy fits 1 WINES ales i Nee Sn NA ats aN The burner assembly system is guaranteed for a period of 3 years from the date of purchase and will be replaced ie Sze am for freight costs only a Ynes i 4 nee xe a S SSRN Ee Pilot valves and thermocouples are guaranteed for a period of one 1 year under the original manufacturers 5 52 1 299 Warranty General Warranty This warranty does not apply in the case of improper installation neglect accident gt gt misuse or as a result of modifications of the original product a le Neat fs hili 22 tgs 2 All costs for removal and re installation are the expressed responsibility of the purchaser SS a For repair replacement or service to defective part s please contact our Customer Service Hotline number below W eS Thereafter with valid warranty registration and proof of purchase call the Customer Service Hotline for authorization 2 1 a to ship defective part prepaid and insured in original carton to Sure Heat Manufacturing A ue e 1861 West Oak Partway Marietta GA 30062 Goods returned improperly packaged are the sole responsibility2. 14 When operating this gas log set the flue damper must be fully open The nominal inlet gas pressure for this appliance is 7 water column for natural gas This appliance must also be disconnected from the gas supply system by closing its individual manual Shutoff valve during any pressure testing at pressure equal to or less than 1 2 PSIG FIREPLACE PREPARATION A Professionally clean chimney and fireplace floor of any combustible material to limit the smell from the system B Open fireplace damper fully and install Damper Stop Clamp with 1 4x2 set screw Part 14 This clamp Is designed to allow any pilot combustion by products to vent See figure 2 Should the Damper Stop Clamp supplied not fit a permanent damper stop clamp must be installed that will keep the damper open ata distance of not less than 1 1 2 Damper must be in the fully open position anytime this unit is in operation C Prior to connecting the gas log set make sure that the gas Supply to the fireplace is completely shut off PREFABRICATED MASONRY FIREPLACE FIREPLACE Figure 2 Damper stop clamp D Prefabricated fireplace Refer to the manufactures fireplace instruction manual for specific information regarding the running of a gas line into that particular model A typical prefab installation involves the insertion of a 1 2 inch gas pipe through the gas line tube provided by each manufacturer from outside the fireplace The Knockout on the insid
3. not fasten the KN KOUT UGS locknut on the flared end ARROWS BURNER PAN Slide the 3 4 burner support spacer Part 10 over the Dual Burner Figure 5 Burner bar placement Bar Part 9 and move spacer to opposite corner of the gas intake connection See Figure 5 Secure the intake end of the Dual burner bar Part 9 to the burner pan Part 8 through the knockout hole selected right or left hand with the 3 8 brass orifice elbow Part 11 3 8 locknut Part 12 and washer Part 21 previously assembled in Step B See Figure 6 Tighten elbow until firmly attached to the Dual burner bar Then firmly tighten the attached lock nut on the elbow to seal the burner bar to the Figure 6 Burner bar connection wall of the burner pan CONNECTING GAS SUPPLY TO BURNER ASSEMBLY Ifa Safety Pilot Kit is to be used please refer to separate installation instructions These instructions refer to Natural Gas applications installed without a Safety Pilot Kit LP NG Safety Pilot Kit available at your local store A B Place burner pan assembly in the center of the fireplace Attach 3 8 Flare X 1 2 NPT gas valve Part 13 to the 1 2 inch gas supply stub already in fireplace Be certain connections are tight and use pipe compound on all male NPT pipe threads to seal joints Attach 3 8 flared tubing Part 15 to burner pan assembly Attach opposite end to gas supply line by carefully bending the flared tub
4. of e Sone y ies purchaser 3 EE NEN Nie ai It is agreed that any repair or replacement is the exclusive remedy from Sure Heat Manufacturing In no case shall an Ge ert H Sure Heat be liable for any consequential damage or breach of this or any other warranty expressed or implied ey Z whatsoever This limitation as to consequential damages shall not apply in states where prohibited se tees Purchased From Date EN a Moiese WA Sa ea Size L 18 L 2a 130 Modi GE oY Ps BC Ne Pes MIMM eau ea MM ES UM es UA es lA Ea WANA es lM es MENAN Ea UMANES WANE a SUUM Sa MIL ea ANNA og I wa WAEIT n ATAT s IA ea MA IY ES NUE Sy WN a NNSA HEME aN al 112 1 21 HAVES ANH E PSA Gut SAC SA 22 4 ANN KE 4414 it ht NRA 4 ra XTX R TAk W HRY iM ASE AS 44 4 it RES AT A BR WEI APAA EAAS Y 4 RAN se sih AA A A AAA N AATA PATAT Please photocopy and return to SHM Intnl within 14 days of purchase you have other questions please contact the Customer Service Hotline 800 229 5647 R84026CC Rev 5 2012
5. INSTALLATION amp OPERATION MANUAL FIREPLACE GAS LOG TIERED DUAL BURNER LOG SET MODELS CCF18NG CCF24NG Burner Set for use with all styles and sizes of SureHeat Dual Burner Natural Gas Log Sets WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or loss of life Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas Supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier INSTALLER Leave this manual with the appliance CONSUMER Retain this manual for future reference SHM INTERNATIONAL 2011 Complies with ANSI 221 84 DUAL BURNER PART LIST Figure 1 GRANULES GLOWING EMBERS 1 6 x 5 HEAVY WEIGHT BAG LIGHT WEIGHT BAG NUMBER OF LOGS ARE DETERMINED BY THE SIZE AND MODEL CHOSEN SETS zoe RANGE FROM 4 TO 9 LOGS 82 GAS LOG 10 TO 1 2 GAS LINE LEFT SIDE 8 S 484 KNOCKOUT 13 PLUG FLARED END RIGHT SIDE
6. KNOCKOUT PLUG TO BURNER BAR EF QTY SET LOGS P 200 90566 ARTNOMBER OTY ed 20 BURNER PAN ip 200 90502__ 1___ iP 200 90604 4 SET 20 SET f gt WIP 190 90523 RMH 120 00420 WIP 120 00350 1 3 8 LOCKNUT RMH 120 00963 VALVE RCODZ00137A DAMPER STOP CLAMP RMH 120 00100 RMH 120 00100 DUAL BUNER BAR WIP 190 9052 1 WIP 130 00300 2 pO 12000180 11 RMH 120 00180 RMH 130 00588 21 WASHER TS IRCODZO0IAEA 1 RCOPZ00007A 3 8 FLARED TUBING WIP 120 90426 WIP 120 90426 GRANULES WIP 130 00010 WIP 130 00010 WIP 190 90560 RMH 120 00100 WARNING Improper use or installation may cause Carbon Monoxide Poisoning Carbon Monoxide is an colorless and odorless gas and is a by product of combustion Caution must be taken to insure the fireplace is properly vented when logs are in use To avoid having potentially dangerous fumes enter the living area be sure the chimney is drawing properly and has sufficient draft WARNING Do not burn wood or other material in any fireplace fitted with a gas log set Do not store or use gasoline or flammable vapors and liquids in the vicinity of this or any other appliance Do not place clothing or other flammable material on or near the appliance e Children and adults should be alerted to the hazards of high surface temperature and should be kept clear to avoid burns or clothing ignition e Young children should be car
7. e of the fireplace is removed as the gas pipe is punched through the fireplace See Figure 3 Masonry fireplace A 1 2 inch gas supply line must be provided to the firebox Most installations require drilling an access hole through the masonry wall The supply line should be secured and sealed by mortar within the access hole The supply line should also have an on off valve either in the wall or inside the fireplace See Figure 4 GAS SUPPLY GAS ON OFF BURNER PAN VALVE INSIDE GAS SUPPLY FIREBOX LINE on s VALVE REPACK MOUNTED IN WALL INSULATION REPACK INSULATION P 14 _ GAS ON OFF eae VALVE IN WALL GAS SUPPLY FIREPLACE LINE 14 Figure 3 Gas line installation Prefabricated Fireplace Figure 4 Gas line installation Masonry Fireplace GAS LOG INSTALLATION See Figure 1 Parts List as a guide to reference part numbers BURNER PAN INSTALLATION NOTE Use pipe compound on all male threads to seal joints A Determine if the fireplace has a right or left hand gas line feed 3 4 SUPPORT SPACER The circular Dimpled hole covering must be knocked out on the UAL appropriate right or left side of the burner pan NOTE Brace pan BURNER BAR on workbench when removing burner knockout Strike knockout with Qn nailpunch for easy removal Locate 3 8 locknut P art 12 and washer Part 21 then fasten them to the 3 8 brass orifice elbow Part 11 Do
8. ee Figure 7B Figure 7 A amp B Granule and Grate Placement NOTE A hammer may be used to tap the back log standoff in place It may be necessary to squeeze the back log standoff with pliers after attaching to the grate Open chimney flue damper to the full open position ar ee e a SSS ro GEE cn FED LORD i Be sure gas supply is shut off Lay match on top of embers and granules near gas burner input Do not hold match in hand See Figure 8 Arto With match burning slowly turn on gas Figure 8 Lighting the log set Proper Log Placement For Vented Gas Logs CCF18NG Canyon Campfire If you have any questions please call 800 229 5647 for customer service crn MAINTENANCE Very little maintenance is required The carbon deposit resulting from combustion is natural and adds to the realistic appearance of the set If carbon becomes excessive it can be lightly brushed or vacuumed away TROUBLE SHOOTING Problem Cause Corrective Action I No Ignition Valve not on turn valve on gas line obstruction inspect supply lines for tube kinks or obstructions 2 Inadequate flame Valve partially closed open valve fully partial gas line obstruction burner inspection for tube kinks or obstructions log arrangement rearrange logs to specified pattern LIMITED WARRANTY
9. efully supervised when they are in the same room as the appliance e Do notuse this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water A fireplace screen must be in place when appliance is operating Unless other provisions are made for combustion air the fireplace screen must have provisions for combustion air e Installation of this Energy Eficient Gas Log Set and provisions for combustion and ventilation air must conform with the National Fuel Gas Code ANSI Z21 84 and appliance local codes e This gas log set is only to be installed and burned in a fully vented fireplace with a fully functional damper and chimney that is free of any obstructions The fireplace must be constructed of non combustible materials and approved to burn wood e To operate this gas log set the fireplace damper must be fully opened ana locked e The smallest or minimum dimension of the chimney flue must be 8 inches in diameter Do not use an Energy efficient Gas Log Setif itis smaller than 8 inches Do not use an Energy Efficient Gas Log Set if fumes from the burner emerge into the room when the damper is fully open This indicates that there is not adequate draft for this log set and it must not be used until the fireplace draft is corrected e This appliance must be installed with a Damper Stop Clamp Part
10. ing as needed to make the connection Avoid kinking the flared tubing while bending If tubing must be cut use a tube cutter Flare the cut end of the tube with a flaring tool NOTE A good method of bending the tube is to fill it with sand bending the tube as needed to make the connection This method will eliminate kinking in the line Once the tube is in the desired configuration for hookup be sure to empty the tube completely of any sand before tube is connected to the gas supply line and the burner Be certain all connections are tight Only use pipe compound on all male NPT pipe threads Test all connections with a soapy water solution with the gas supply turned on If bubbles appear on any connection retighten and retest Once itis determined there are no leaks whatsoever turn off gas supply and move to next assembly step GRANULE EMBER AND GRATE PLACEMENT A LIGHTING YOUR GAS LOG SET Manual Valve only A B Attach back log Standoff Part 18 to the back part of the grate Spread granules Part 16 over the installed burner pan Granules Should be sloped to the same angle as the burner pan filling the entire pan See Figure 7A Spread glowing embers Part 17 evenly over the top of the granules covering the entire surface area concentrating on the front and sides of the burner pan for the most realistic burning effect Place log grate Part 7 over the burner pan aligning as shown See Figure 7B S
Download Pdf Manuals
Related Search