PULSE Showerspas 1018 Installation Guide
Contents
1. Nylon Top inserted Qty 2 Allen Set Screw inserted Qty 1 Hand Held Hose Outlet attached2. the finished wall surface tile or backing material it is advisable to purchase a PULSE ShowerSpa model that covers the location of the existing valve assembly either single handle or two handle type If your PULSE ShowerSpa model does not cover this area you will need to either choose another PULSE ShowerSpa model that does or make the necessary repairs with appropriate materials i e wallboard tile fiberglass etc 1 Turn off the water supply to the shower Note Typically there is a gate valve where the water main enters the house Turning the water valve off at the hot water tank does not turn off the cold water supply line 2 Make certain the water is completely turned off to both hot amp cold supply lines of the Shower Turn the shower valve on both hot and cold to verify the water supply is off Open a sink faucet in the bathroom in which you are installing the ShowerSpa to relieve any pressure and help adequately drain the shower supply lines ae a a a Navajo ShowerSpa Numbered Components Shower Head Shower Arm Hand Held Shower Wand Hand Held Mount Glass Shelf Stainless Steel Hose ORB Shower Panel Wall Mount Tapered End of Hose Hexagon Nut End of Hose Soft Washer Shower Arm Nuts Mounting Screw Panel Bracket Mounting Anchor Panel Bracket ty 2 Mounting Screw Hand Held Mount blk Mounting Anchor Hand Held Mount Screen 3mm Washer inserted 3mm Washer V Allen Set Screw w
3. ate By installing the check valve the pressure is maintained within the valve eliminating the knocking sound Wall Bracket 1812 SHOWERSPAS wel 1 86 uVC uAG L uG L 09 ark bottom of ShowerSpa M 1214 Finished Floor mensions D New Construction Extensive Remodel New Finished Wall Surface Prior to sheetrock stub out 1 2 hot and cold supply lines beyond the finished wall surface 4 on center The height of the Stub outs is completely dependent upon the desired mounting height of the Navajo ShowerSpa For a person 5 8 6 2 we recommend the stub outs to be 35 from the finished floor 2 After the finished wall surface has been completed make certain the water is completely turned off to both hot amp cold supply lines of the Shower Connect the 90 male threaded fittings to the stub outs maintaining 1 4 1 2 space between the fitting and finished wall The open end of the threaded male fitting should point down 3 Mark the location of the holes for the mounting bracket making sure the bracket is level For a person 5 8 62 tall we recommend 53 from finished floor height Before drilling holes for the bracket make certain the ShowerSpa will rest flat against finished wall surface at the desired mounting height with the supply lines connected 4 Drill 1 4 holes through the wal
4. e PULSE SHOWERSPAS Manufacturer s Limited Warranty PULSE Shower Spas Inc warrants that all ShowerSpas are free from defect in workmanship and or materials for a period of three years from the date of purchase This warranty extends to the original purchaser only and is non transferable This warranty does not cover and PULSE Showerspas will not pay for conditions malfunctions or damages resulting from 1 normal wear and tear improper installation whether performed by a contractor service company or the consumer improper maintenance misuse abuse negligence accident or alteration 2 the use of abrasive and or caustic cleaning agents or no rinse cleaning products or the use of the product in any manner contrary to the product instruction or 3 conditions in the home such as excessive water pressure or corrosion Should any ShowerSpa be determined by PULSE Showerspas Inc to be defective in normal residential use at the option of PULSE Showerspas Inc such product shall either be replaced or repaired and returned to the customer free of defects The consumer shall give notice of any defects to PULSE Showerspas Inc within thirty days of discovery of such defect Proof of purchase original sales receipt must be provided to PULSE Shower Spas Inc with all warranty claims PULSE Shower Spas Inc is not responsible for labor charges removal charges installation or other consequential costs In no event shall the
5. l surface using a masonry bit Drill slowly through wall surface to avoid cracking and chipping Insert anchor and securely screw bracket to wall Before connecting hot and cold supply lines mount the ShowerSpa on the wall checking the height and making sure the ShowerSpa feels secure 5 Connect hot and cold water supply lines to male threaded pipe do not over tighten Before mount ing the ShowerSpa check the fittings to make sure they are secure Turn on water and check for leaks When fittings are leak free mount ShowerSpa on wall 6 Hold hand held mount to desired height making sure flexible hose reaches mount Recommended 4 to 6 from ShowerSpa on the right side of the unit so you can easily remove hand held wand Position mount flat on surface make two marks with pencil Carefully drill 4 holes through the wall surface using masonry bit Insert anchors and securely screw mount to wall 7 Optional Seal around the body of ShowerSpa with a bead of silicone 1 The desired mounting height of the ShowerSpa determines the height of the 1 2 stub outs The stub outs must be located at a height allowing the supply lines to be connected and the body of the ShowerSpa to rest flat against the finished wall This height may vary depending on several factors i e location of supply lines interference from ShowerSpa plumbing personal preference etc Retrofitting An Existing Shower Note In a re model in which you are not replacing
6. liability of PULSE Showerspas Inc exceed the purchase price of the ShowerSpa Some states provinces do not allow limitations of how long an implied warranty lasts or the exclusion or limitation of such damages so these limitations and exclusions may not apply to you This warranty gives the consumer specific legal rights You may also have other rights that vary from state province to state province Follow manufacturers recommended installation Use caution with children under ten years of age Do not use ShowerSpa as a support device Do not use harsh chemicals or abrasives when cleaning Turn water supply off when servicing ShowerSpa PULSE Showerspas Inc 49 Hangar Way Suite A Watsonville CA 95076 888 785 7320 email info pulseshowerspas com website www pulseshowerspas com e PULSE SHOWERSPAS Navajo ShowerSpa Installation Instructions Model 1018 Navajo Model 1018 PLEASE READ THE FOLLOWING INSTRUCTIONS COMPLETELY BEFORE BEGINNING Our goal is to ensure your installation goes smoothly and safely Please read these safety instructions carefully and follow recommendations for plumbing and mounting If after reading instruction manual you determine you do not have the necessary skills and or tools we then recommend a licensed plumbing contractor complete the installation If you encounter any eee during installation call Technical Support toll free at 888 785 7320 before returning item to store You
7. pe do not over tighten Before you mount the ShowerSpa check the fittings to make sure they are secure Turn on water and check for leaks When fittings are leak free mount ShowerSpa on wall Hold hand held mount to desired height making sure flexible hose reaches mount Recommended 4 to 6 from ShowerSpa on the right side of the unit so you can easily remove hand held wand Position mount flat on surface make two marks with pencil Carefully drill holes through the wall surface using masonry bit Insert anchors and securely screw mount to wall Optional Seal around the body of ShowerSpa with a bead of silicone Additional fittings may be necessary depending on your specific situation This height can vary depending on several factors i e location of supply lines old valve access area personal preference etc ATTENTION ONCE YOUR UNITS IS INSTALLED IF YOU HEAR A KNOCKING SOUND WITHIN THE UNIT WHICH SOUNDS LIKE IT IS COMING FROM INSIDE THE WALL WE HAVE A CHECK VALVE THAT WILL ELIMINATE THIS a ea Be a PULSE SHOWER SPAS AT 888 785 7 We will send you a check valve free of charge PULSE uses a cUPC certified pressure balanced valve which is designed to prevent scalding and maintain a consistent water temperature If there is a sudden drop in water pressure i e flushing toilet turning on a faucet etc the valve will compensate for the drop in water pressure by knocking to maintain the flow r
8. uld also cut the riser within the wall supplying the existing shower head Carefully twist and remove the valve 5 Unscrew the old shower head from the arm and then unscrew the arm 6 It is recommended to extend the water supply lines outside the wall cavity parallel to the finished wall surface Attach a male threaded fitting to each supply line maintaining 1 4 1 2 space between the male threaded fittings and the finished wall The open end of the male fitting should point down For your convenience we have included 2 1 2 90 fittings Make certain the location height width of the stub outs and connecting to them does not interfere with the desired mounting height of the ShowerSpa Mark the location of the holes for the mounting bracket making sure the bracket is level For a person 5 8 62 tall we recommend 53 from finished floor height Before drilling holes for the bracket make certain the ShowerSpa will rest flat against finished wall surface at the desired mounting height with the supply lines connected Drill 1 4 holes through the wall surface using a masonry bit Drill slowly through wall surface to o_o NO avoid cracking and chipping Insert anchors and securely screw bracket to wall Before connecting the hot and cold supply lines mount the ShowerSpa on the wall checking the height and making sure the ShowerSpa feels secure Connect hot and cold water supply lines to male threaded pi
9. will need the following tools Level Tape Measure Soft pencil or felt pen to mark tile Drill Preferably cordless A Reciprocating Saw w metal cutting blade Sawzall Channel Locks or adjustable wrench Ys Masonry Drill Bit oC qa gt I i ShowerSpa Assembly 1 Shower Arm Align two mounts with pre drilled holes in ShowerSpa To align top mount loosen allen set screw 19 inside mount and adjust accordingly to fit top hole Insert threaded mount through holes in showerSpa and secure with soft washer 10 and nut 11 supplied Tighten set screw 19 inside mount CAUTION Do NOT over tighten set screw Attach shower head supply line to the lower shower arm mount Make sure rubber washer is inserted inside fitting Install shower head onto shower arm 2 Glass Shelf Position glass shelf into slotted mounts Secure allen set screws 18 on the under side of mounts Do NOT over tighten Screws 3 Hand Held Hose and Wand Attach hexagon nut end of hose 9 to hand held hose outlet 20 NOTE Make sure rubber washers are inserted in each end of hose Attach tapered end of hose 8 to hand held wand 3 3 Remove the handle s and trim cover s of your existing valve exposing the valve body in the wall 4 Locate the hot and cold supply lines entering the valve Using a reciprocating saw with sharp metal saw blade cut the existing valve out preserving the threads of the supply lines entering the valve Note you sho
Download Pdf Manuals
Related Search