DreamLine SHDR-20307210F-HFR-01 Installation Guide
Contents
1. Style B and C Stationary Glass Assembly and Installation NOTE Use parts from Diagram B or C depending on your model style for the Stationary Glass assembly and installation Style B Style C 10 Apply clear silicone along the inner channel of the Glass profile 10 and push the Stationary glass 11 inside the channel NOTE If you have difficulty sliding the Glass profile over the Stationary glass you can slightly tap on the Glass profile with a rubber mallet and a piece of wood See Fig 10 1 Fig 10 2 and Fig 10 3 for details NEVER use the metal hammer or hit the profile without the wood bumper 1 He Push the Stationary glass with attached Glass profile inside the Wall profile 09 See Fig 10 4 for details NOTE Please note that the hole in the corner of the Glass panel should be at the bottom farther from the wall UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 10 12 Press the Anti Water strip 19 on the vertical edge of the Stationary glass 11 Align the Stationary glass with the Glass Door 01 and then close the Glass door If needed adjust the position of the Stationary glass to make sure the Anti water strip 19 and the Glass door 01 work well See Fig 11 for de2. 28 Apply the sealant along the connection of the Stationary glass to the wall and the Shower base or threshold See Fig 28 for details Water Silicone Fig 28 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 23 Style E Shower Enclosure Assembly and Installation NOTE Use parts from Diagram A and Diagram D for the Shower Enclosure assembly and installation 29 Please draw the lines on the wall for the Glass door A ee i W2 and the Return panel B according to the size of your model in the size table below se See Fig 29 for details Size Table A W1 SHDR GL2001 287210 28 1 4 718mm SHDR GL2001 297210 29 1 4 743mm SHDR GL2001 307210 30 5 16 770mm B W2 i SHDR GL2312 307210 30 1 16 763mm SHDR GL2312 327210 32 1 16 814mm SHDR GL2012 347210 34 864mm A A B let A Fig 29 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 24 30 Attach the Hinges 05 to the Glass door 01 See Fig 30 for details ATTENTION Never set your glass down directly onto a tile or concrete floor Always use a piece of wood or cardboard and leave the corner pads on the glass until it becomes necessary to remove them to protect the bottom edge and the corners of the glass from breakage 31 Place a piece of flat
3. BREAMLINE dream In style UNIDOOR RADIANCE SHOWER DOOR ENCLOSURE INSTALLATION INSTRUCTIONS MODEL _ STYLE lt i W SELECTOR Please choose your door model style and selector according to your order for easy installation ATTENTION This door is extremely hea and the hinges on this door must be attached to the studs or to preinstalled 2 X 6 wood reinforcement behind the wall IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Style A Style B Style C Style D Style E Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DrearzLine Shower Doors and Enclosure please visit www BathAuthority com Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by
4. glass 11 drill the holes in the Glass profile 10 through predrilled holes in the Wall profile 09 using 1 8 drill bit NOTE You only need to drill through the first layer of the Glass Profile Use Round head screws ST4 2 X 10 14 to 1 16 1 8 After final adjustments of the Stationary i attach the Wall profile to the Glass profile Cover the exposed screw heads with 3 Decorative screw cover 17 See Fig 14 amp 15 for details Fig 14 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 12 16 Apply the sealant along the connection of the Stationary glass to the wall and the Shower base or the threshold If the Stationary Panel width is 6 the installation is finished If the Stationary Glass width is 12 and over you will need to continue your installation from a Style B for Support Bar installation b Style C for Glass Shelves installation Style B Style C Fig 15 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 13 Style B Support bar Assembly and Installation NOTE Use parts from Diagram B for the Support Bar assembly and installation 17 Locate the Support bar 12 Adjust the bar to a proper position on the glass and the wall Level it horizontally Hold it firmly and outline the bra
5. 19 makes tight contact to the Glass Door from top to bottom Outline the position of the Wall brackets 24 on the wall from inside the shower See Fig 23 for details inside PLEASE NOTE The top of the Stationary glass must be leveled with the top of the Glass door outside inside Fig 22 outside 2 inside Fig 23 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 19 24 Open the Glass Door 01 and carefully set the Stationary glass 11 aside Remove the Wall brackets 24 from the Stationary glass and replace it to the outlined position to mark the hole on the wall Drill the hole using a 5 16 drill bit insert the Wall anchor 13 and fasten the Wall brackets to the wall with the Big flat head screws ST4 2x55 15 See Fig 24 for details 25 Place Stationary Glass 11 back into position and tighten it up to the Wall Bracket 24 See Fig 25 for details inner part d 5 16 Fig 24 J inside 3 inside Jl outside Fig 25 outside J inside UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 20 26 To adjust and secure the Stationary Glass 11 in place install the Bottom Bracket 18 to the Stationary glass Drill the hole into the shower base or the threshold through oval notched hole in the Bottom bracket using 1 8 drill bit Use the Round head screws ST4 2x35 16 to
6. UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 2 Place a piece of flat timber 5 8 thick on the threshold or the shower base Remove the corner pads from the Glass door 01 Place the Glass door on the flat timber Carefully butt up the door with hinged side against the wall adjust its position and level it vertically ATTENTION Please check with a level and be sure that the door is absolutely plumb See Fig 2 for details 5 8 3 Hold the door in place and mark the drill 1 holes for both Hinges 05 on the wall Set the door aside and drill the holes in the wall using 1 4 drill bit Place the Glass door 01 back on the flat timber and attach both hinges to the wall with only two Countersunk screws ST5x70 04 on the hinge from outside outside of the shower See Fig 3 for details ATTENTION This door is extremely heavy and the hinges on this door must be attached to the studs or to preinstalled 2 X 6 wood reinforcement behind the wall 1 4 outside Fig 3 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 ATTENTION 1 acide 2 Back plate of the hinge from inside the shower locates too close to the drilled holes in the wall and might get A scratched with the long screws or i i screwdriver A OPTIONAL 4 Carefully remove back plates from the Hinges 05 and set t
7. attach the Bottom Bracket to the shower base or the threshold Cover the screw head with Decorative screw cover 17 See Fig 26 for details mado Sok 4 1 8 Fig 26 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 21 Style D Support Bar Assembly and Installation NOTE Use parts from Diagram D for the Support Bar assembly and installation ATTENTION If width of the Stationary Glass is 12 and over you must install Support Bar for stability 27 Locate the Support bar 12 Adjust the bar to a proper position on the glass and the wall Level it horizontally Hold it firmly and outline the bracket s position on the wall Remove the Support bar and detach the wall bracket from it Place the wall bracket against its outlined position on the wall and mark the drilling hole Drill the hole using 5 16 drill bit insert the Wall anchor 13 and fasten the wall bracket to the wall with the Big flat head screws ST4 2 55 15 Attach the Support bar to the wall as shown on Fig 27 6 and tighten the set screws and the glass holding screw to secure the glass See Fig 27 for details 1 2 inside G Yu WY Z outside 3 4 Pa 5 16 s a0 A i 4 is A A L a p Fig 27 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 22
8. builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or l
9. its position and reassemble the Hinges See Fig 33 and Fig 34 for details 1 2 l 5 16 outside 3 4 l outside Fig 32 1 inside 2 3 inside 4 ro Fig 33 inside UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 26 34 Mount the two Wall brackets 24 through the notches on the Stationary glass 11 See Fig 35 for details Fig 34 Fig 35 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 27 35 Press the Anti water strip 20 onto the vertical edge of the Stationary glass 11 Carefully butt the Stationary glass up against the wall vertically according to the measurements in size table While securely holding the Stationary glass close the Glass Door 01 and align the Stationary glass to it If needed adjust the position of the Stationary glass to make sure the Anti Water strip 20 makes tight contact to the Glass Door from top to bottom Outline the position of the Wall brackets 24 on the wall from inside the shower See Fig 36 for details 36 Open the Glass Door 01 and carefully set the Stationary glass 11 aside Remove the Wall brackets 24 from the Stationary glass and replace it to the outlined position to mark the hole on the wall Drill the hole using a 5 16 drill bit insert the Wall anchor 13 and fasten the Wall bracke
10. timber 5 8 thick on the threshold or the shower base Remove the corner pads from the Glass door 01 Place the Glass door on the flat timber Carefully butt up the door with hinged side against the wall adjust its position and level it vertically ATTENTION Please check with a level and be sure that the door is absolutely plumb See Fig 31 for details nye NI outside Fig 30 Fig 31 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 25 32 Hold the door in place and mark the drill 33 holes for both Hinges 05 on the wall Set the door aside and drill the holes in the wall using 1 4 drill bit Place the Glass door 01 back on the flat timber and attach both hinges to the wall with only two Countersunk screws ST5x70 04 on the hinge from outside of the shower See Fig 32 for details ATTENTION This door is extremely heavy and the hinges on this door must be attached to the studs or to preinstalled 2 X 6 wood reinforcement behind the wall ATTENTION Back plate of the hinge from inside the shower locates too close to the drilled holes in the wall and might get scratched with the long screws or screwdriver OPTIONAL Carefully remove back plates from the Hinges 05 and set the Glass door 01 aside Screw in rest of the Countersunk screws ST5 x 70 04 into the wall place the Glass door back to
11. DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or
12. cket s position on the wall Remove the Support bar and detach the wall bracket from it Place the wall bracket against its outlined position on the wall and mark the drilling hole Drill the hole using 5 16 drill bit insert the Wall anchor 13 and fasten the wall bracket to the wall with the Big flat head screws ST4 2 X40 15 Attach the Support bar to the wall as shown on Fig 16 6 and tighten the set screws and the glass holding screw to secure the glass See Fig 16 for details Fig 16 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 14 18 Apply the sealant along the connection of the Stationary glass to the wall and the Shower base or the threshold See Fig 17 for details Fig 17 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 15 Style C Glass Shelves Assembly and Installation NOTE Use parts from Diagram C for the Glass Shelves assembly and installation 19 Mark the Glass shelf 12 position on the wall According to the measurements in Fig 18 1 mark the drilling holes for the Shelf brackets without nut 22 Drill the holes using 5 16 drill bit and insert the Wall anchors 13 Attach the Shelf brackets without nut to the wall using the Countersunk screw ST4 2 X 40 23 and attach the Shelf brackets with nut 21 to the Stationary glass 11 Insert the Glas
13. e Bottom anti water strip inside outside NOTICE Make sure the Handle side of the Glass 3 door tight to the Anti water strip 07 along the vertical edge when the door is shut See Fig 7 for details _jinside outside TS Fig 6 3 8 2 A N inside eg i NN inside outside N Fig 7 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 ATTENTION Prior to the next step please be sure the part of the wall for installation of the L shaped strip 08 is clean dry and free from soap oil and any construction debris 8 With the door closed place the L shaped strip 08 on the door edge and mark its location on the wall Please note that the corner of the L shaped strip 08 should face inward Open the door Gently remove the plastic tape from the adhesive side of the L shaped strip 08 and firmly press it to the wall See Fig 8 for details 9 It is the last step for Style A products See Fig 9 for details NOTE If your door is more than 30 in width you will need to add Stationary glass panel 11 a For installation of the Stationary Glass with Support bar you will need to refer to Style B b For installation of the Stationary Glass with Glass Shelves you will need to refer to Style C Fig 8 Fig 9 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013
14. erformed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR
15. ers and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 32 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Ins
16. hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement STYLE A Single Shower door 23 30 Diagram A must be used for assembly Pages 5 9 STYLE B Shower door with 6 small or 12 30 large Stationary glass Diagram A and Diagram B must be used for assembly Pages 5 9 10 12 14 15 STYLE C Shower door with 12 30 large Stationary glass Diagram A and Diagram C must be used for assembly Pages 5 9 10 12 16 17 STYLE D Shower door with 6 small or 14 30 large Stationary glass Diagram A and Diagram D must be used for assembly Pages 5 9 18 21 22 23 STYLE E Shower enclosure with 30 Return Stationary glass Diagram A and Diagram D must be used for assembly Pages 24 32 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 Style A Single Shower Door Assembly and Installation NOTE Use parts from Diagram A for the Single Shower door assembly and installation 1 Attach the Hinges 05 to the Glass door 01 See Fig 1 for details i b l ATTENTION Never set your glass down directly outside onto a tile or concrete floor o Always use a piece of wood or cardboard 2 and leave the corner pads on the glass until it becomes necessary to remove them to protect the bottom edge and the corners of the glass from breakage inside Fig 1
17. hat some adjustments and drilling may be necessary Please protect all primary surfaces of the product during installation Never set your glass down directly onto a tile floor Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass 5 Please NOTE The doors that are under 30 do not have out of plumb adjustment Make sure your walls are at right angles 6 Attention Parts packed inside carton are for common use so there will be some parts that you will not use or there will be some remaining parts Tools Required i Tape l Phillips Drill bit Drill bit Drill bit Caulk Measure Pencil Screwdriver 5 16 1 4 1 8 Wood S Caulk Level Gun aan I Hammer Mallet Knife UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 2 Detailed Diagrams of Shower Door Components Diagram A Diagram B Diagram C Diagram D 4 12 11 10 9 L a 8 ue P ie y N 13 i 4 5 13 o 14 aad k JE A m 15 15 fi mas le p ae 16 oasis 6 2 pom 16 a 17 ors iy 18 17 18 7 i St p 19 a i hy 20 8 M 19 21 i 5 ii 24 22 G 23 women Diagram A 01 Glass door 1pc 06 Side strip 3 sections to cut 1pc 02 Handle 1pc 07 Bottom anti water strip 1pc 04 Countersunk screw ST5 X70 8pcs 08 L shaped stri
18. he Glass door 01 aside Screw in rest of the Countersunk screws ST5 x 70 04 into the wall As place the Glass door back to its position and reassemble the Hinges 3 inside 4 S inside igs See Fig 4 and Fig 5 for details Fig 4 NN 5 Mount the Handle 02 to the Glass door 01 See Fig 5 for details NN Fig 5 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 e from the top edge of the Glass door 01 to the upper body of the top Hinge 05 e from the lower body of the upper Hinge to the upper body of the bottom Hinge 6 Get three measurements 1 e from the lower body of the bottom Hinge to Into the hinge 1 16 above the shower base measurements Notch the cut strips to be able to slide them into the Hinge to cover the space to the wall Remove the timber plate fully open the Glass door Cut the Side strip 06 according to the 3 Into the hinge 4 ij and press the cut strips on the vertical edge of the Glass door See Fig 6 for details Handle side 1 7 Measure the bottom of the Glass door strip end 01 from the Side strip 06 to the vertical edge on the Handle 02 side Cut the Bottom anti water strip 07 to the size of your measurement and notch 3 8 of the inner side of th
19. imitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such a photos may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com EAMLINE gt dream in style TEL 866 731 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Doors and Enclosure please visit www BathAuthority com
20. implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be p
21. marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 If this unit is going to be installed in a new construction please install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation 4 Prior to the installation please ensure that the installation surface is level and solid and will be able to support the total weight of the unit Also make sure that the walls are plumb Depending on the type of unit you are installing some adjustments in leveling may be possible However irregular installation surface level or out of square conditions can result in serious problems for your installation Please note t
22. p 1pc 05 Hinge 2pcs Diagram B 09 Wall profile 1pc 15 Big flat head screw ST4 2 X40 Apcs 1pc 10 Glass profile 1pc 16 Round head screw ST4 2 X35 1pc 11 Stationary glass 1pc 17 Decorative screw cover 5pcs 12 Support bar lpc 18 Bottom bracket 1pc 13 Wall Anchor 4pcs 1pc 19 Anti Water strip Door 1pc 14 Round head screw ST4 2X 10 4pcs Diagram C 09 Wall profile 1pc 16 Round head screw ST4 2 X 35 1pc 10 Glass profile 1pc 17 Decorative screw cover 5pcs 11 Stationary glass 1pc 18 Bottom bracket 1pc 12 Glass shelf 2pcs 19 Anti Water strip Door 1pc 13 Wall anchor 8pcs 21 Shelf bracket with nut 2pcs 14 Round head screw ST4 2 X10 4pcs 22 Shelf bracket without nut 4pcs 15 Big flat head screw ST4 2 X40 4pcs 23 Countersunk screw ST4 2 X40 4pcs Diagram D 11 Stationary glass 1pc 17 Decorative screw cover 1pc 12 Support bar lpc 18 Bottom bracket 1pc 13 Wall anchor 2pcs 1pc 19 Anti Water strip Door 1pc 15 Big flat head screw ST4 2 X 55 2pcs 1pc 20 Anti Water strip Enclosure 1pc 16 Round head screw ST4 2 X35 1pc 24 Wall bracket 2pcs ATTENTION All parts that marked with the star not provided with 6 Stationary panel UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using detailed diagram in your manual as a reference Before discarding the carton check for small
23. rement and notch 3 8 of 2 inside the inner side of the Bottom anti K water strip putside NOTICE Make sure the Handle side of the 3 Glass door tight to the Anti water strip 07 along the vertical edge when the door is shut See Fig 43 for details outside FX Fig 43 Fig 42 3 8 2 i inside outside ty inside outside IN UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 31 42 Run a strip of masking painter s tape along the connection of the Stationary glass with the wall and the Shower base or threshold for an accurate job leaving a gap of about 1 16 Apply a bead of Kitchen amp Bath Waterproof silicone along the interior perimeter run a wet finger along the line of sealant and remove the tape Let the silicone cure according its direction See Fig 44 for details Fig 44 Maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Silicon Never use abrasive clean
24. s shelves into the Shelf brackets and fasten the screws at the bottom of the brackets See Fig 18 and Fig 19 for details UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 16 20 Apply the sealant along the connection of the Stationary glass to the wall and the Shower base or the threshold See Fig 20 for details UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 i oft AA uy if Caulk Fig 20 17 Style D Stationary Glass Assembly and Installation NOTE Use parts from Diagram D for the Stationary Glass assembly and installation 21 Mount the two Wall bracket 24 through the notches on the Stationary glass 11 Press the Anti water strip 19 onto the vertical edge of the Stationary glass See Fig 21 for details 1 2 outside outside g J 3 inside 4 inside outside KL outside Fig 21 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 18 22 Carefully butt the Stationary glass 11 up against the wall vertically See Fig 22 for details outside 23 While securely holding the Stationary glass 11 close the Glass Door 01 and align the Stationary glass to it a If needed adjust the position of the Stationary glass to make sure the Anti Water strip
25. tails Please note The Stationary glass must be leveled with the Glass door 13 Draw a line along the inner edge of the Wall profile 09 on the wall Detach the Wall profile from the Stationary glass 11 and the Glass profile 10 assembly Place the Wall profile to the outlined position and mark the drilling holes through the predrilled holes in the Wall profile Now drill the holes using 5 16 drill bit in the wall and insert the Wall anchors 13 into the holes Apply silicone along the Wall profile and around the holes Fasten the Wall profile to the wall with the Big flat head Screw ST4 2 X40 15 Then push the Stationary glass and Glass profile assembly into the Wall profile See Fig 12 for details UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 11 14 Adjust the Stationary glass 11 position to ensure that when the glass door is closed there is a gap 1 16 1 8 between the two glass panels To adjust and secure the stationary glass in place install the Bottom Bracket 18 to the Stationary glass Mark the drilling hole for the bracket Make sure the mark is clear and visible and drill the hole using 1 8 drill bit Use the Round head screws ST4 2X35 16 to attach the Bottom Bracket to the shower base or the threshold Cover the screw head with Decorative screw cover 17 See Fig 13 for details 1 uo
26. tallation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or
27. the drilling hole Drill the hole using 5 16 drill bit Insert the Wall anchor 13 and fasten the bracket to the wall with the Big flat head screw ST4 2 x 55 15 Attach the Support bar to the wall and the Stationary glass with gasket in place as shown on Fig 13 5 and tighten the set screws and the glass holding screw to secure the glass See Fig 41 for details inside dye Va outside 3 5 16 oo Fig 41 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 30 e from the top edge of the Glass door 01 to the upper body of the top Hinge 05 e from the lower body of the upper Hinge to the upper body of the bottom Hinge e from the lower body of the bottom Hinge to 1 16 AO Get three measurements 1 2 Into the hinge above the shower base Cut the Side strip 06 according to the measurements Notch the cut strips to be able to slide them into the Hinge to cover the space to the wall Remove the timber plate fully open the Glass door and press the cut strips on the vertical edge of the Into the hinge 4 i Glass door 5 See Fig 42 for details 1 16 T Handle side 1 a strip end He Measure the bottom of the Glass door 01 from the Side strip 06 to the vertical edge on the Handle 02 side Cut the Bottom anti water strip 07 to the size of your measu
28. ts to the wall with the Big flat head screws ST4 2x55 15 See Fig 37 for details Fig 36 1 2 ej a inner part 3 4 th l 5 16 5 6 Fig 37 UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 28 37 Place Stationary Glass 11 back into position and tighten it up to the Wall Bracket 24 See Fig 38 for details 38 To adjust and secure the Stationary Glass 11 in place install the Bottom Bracket 18 to the Stationary glass Drill the hole into the shower base or the threshold through oval notched hole in the Bottom bracket using 1 8 drill bit Use the Round head screws ST4 2x35 16 to attach the Bottom Bracket to the shower base or the threshold Cover the screw head with Decorative screw cover 17 See Fig 39 and Fig 40 for details inside l inside 1 inside outside Fig 38 Fig 39 outside inside UNIDOOR RADIANCE Rev 4 Ver 2 06 2013 29 39 Locate the Support bar 12 Adjust the Support bar to a proper position on the Stationary glass 11 and the wall Level it horizontally Hold it firmly and outline the bracket s position on the wall Remove the Support bar and detach the wall bracket from it Place the bracket against its outlined position on the wall and mark
Download Pdf Manuals
Related Search