DreamLine SHEN-24365340-06 Installation Guide
Contents
1. DREAMLINE ream in style UNIDOOR PLUS STYLE I SHOWER ENCLOSURE GLASS PANEL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Style ATTENTION This model features the half etched glass option Please see specific installation instructions on page 20 when applicable Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Doors and Enclosure please visit www BathAuthority com UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Glass Panel Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our cust2. before applying silicone See Fig 12 amp 13 for details Fig 12 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 11 Straight cut the U channel 1 76 wall profile 09 at the top mark that was made in step 8 Place the U Channel 1 wall profile on the U Channel 2 bottom profile 29 and align vertically with the inside wall mark Mark the drill holes on the wall through the predrilled holes in the U Channel 1 Now drill holes in the wall using 5 16 drill bit and insert the 5 16 Wall anchors 13 See Fig 14 for details Fig 14 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 11 12 Apply waterproof silicone along the bottom surface and around the holes of the U Channel 1 76 wall profile 09 Fasten the U Channel 1 to the wall with the Countersunk screw ST4 2x40 23 Apply Waterproof silicone into the groove of both U Channels See Fig 15 amp 16 for details waterproof silicone Fig 15 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 12 13 Slide the Return panel glass 26 into the groove of both U Channels NOTE If you have difficulty sliding the Return panel glass into the U Channels you can slightly tap on the Return panel glass with a rubber mallet and a piece of wood See fig 17 amp
3. panel L NOTE You will be doing straight and 45 cuts for this enclosure installation All 45 cuts are from the outside dimension tip to tip It may be necessary to remove any burrs from the cut end of the U channels gt gt with a metal file before placing the U channel onto the glass H Use a miter saw to rough straight cut one of the U channel 2 40 bottom profiles 29 to the actual width of the glass 1 1 4 See Fig 3 amp 4 for details Fig 3 Fig 4 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 5 Slip the cut U channel 2 40 bottom profile 29 TS SS 2 and uncut U channel 1 76 wall profile 09 onto A the Return panel glass 26 in the shown locations wall With the door open place the Return panel glass on U channel 1 Return threshold adjacent to door and in line with the wall ice mark Adjust the Return panel glass and U channel 1 wall profile against the wall to compensate for any out of plumb conditions ensuring that the 3 Return panel glass is level vertically and U channel 1 is flush with the wall Mark the U channel 2 bottom profile end L opposite of the wall at the exposed vertical glass DoS inside U channel 2 edge inside AIS Remove the U channel 2 bottom profile Leave J1 the U channel 1 wall profile on the Return panel Mak gt n 5 6 glass Set the Ret
4. 18 for details xe J Fig 17 Fig 18 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 13 14 Place the U Channel 2 bottom profile eo inside 29 for the Stationary glass 11 onto the ONN threshold base in line with the inside threshold mark and flush with 45 corner cut a Mark the drill holes on the threshold 1 Na 2 through the predrilled holes in the U Channel 2 and drill the holes using 01 8 T o18 cae Wa drill bit SEn Apply waterproof silicone along the bottom i E we p surface and around the holes of the U EN ae LA Channel 2 and fasten it to the base with N i the Countersunk screws ST4 2 X 40 23 3 n mA _ outside ai waterproof NOTE The surface needs to be clean and free of debris before applying silicone See Fig 19 amp 20 for details Fig 20 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 15 Apply Waterproof silicone into the groove of the U Channel 2 bottom profile 29 and sparingly along the vertical edge of the Return panel glass 26 See Fig 21 amp 22 for details waterproof silicone outside inside Fig 21 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06
5. 2014 15 16 Slide the Stationary glass 11 into the groove of the U Channel Make sure the vertical edge of the Stationary glass is flush with outer face of the Return panel glass 26 at the corner Apply a bead of silicone on the open end of the U Channel and its connection NOTE If you have difficulty sliding the Stationary glass into the U Channel you can slightly tap on the Stationary glass with a rubber mallet and a piece of wood See fig 23 amp 24 for details Fig 24 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 16 17 Attach the 90 Corner Bracket 30 to the top corner of both glass panels Ensure that the 90 Corner Bracket is square and gaskets are aligned properly before tightening the glass holding screws Temporarily secure the bottom corner of the glass panels with a generous strip of Painters tape to keep the corner tight until the silicone cures See fig 25 amp 26 for details inside rea H Y Fig 25 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 17 18 Apply waterproof silicone along the connection of all U Channels to the wall and threshold on the inside of shower Carefully apply an even bead of silicone down the inside corner of the glass panels See Fig 27 amp 28 for details wate
6. LAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under norma
7. S WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such as photos may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 21 EAMLINE dream in style TEL 866 731 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Doors and Enclosure please visit www BathAuthority com UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 22
8. THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays D
9. bottom edge and corners of the glass 5 Note The installation of this unit requires that you drill down into the threshold Tools Required ke Ca a SLOS KY RL Noms ee d x Tape Phillips Drill bit Drill bit Caulk Painters Tape Measure Pencil Screwdriver 5 16 1 8 Yoo Mfg FWS L pL yy As J SS 8 2 XV AS Y OK te gt P Caulk Electric Xa Level Gun Hammer V Mallet Wood Miter saw Drill UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 2 Detailed Diagram of Glass Panel Components 13 a Ss ee te ie A i 30 T 23 i 28 26 SQN 9 E gt Packing List 09 U channel 1 76 wall profile 1pc 23 Countersunk screw ST4 2x40 28pcs 11 Stationary glass 1pc 26 Return panel glass 1pc 13 5 16 Wall anchor 28pcs 28 Adjustment Spacer 6pcs 19 Anti Water strip inline panel 1pc 29 U channel 2 40 bottom profile 2pcs 20 Anti Water strip enclosure 1pc 30 90 Corner Bracket 1pc NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for repla
10. cement The shipping boxes may contain extra parts not used in your model configuration ATTENTION Anti Water strip enclosure 20 used for 30 34 return stationary panel Installation STYLE L UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 3 Style T In Line Panel with 30 34 Return Panel Installation NOTE The Unidoor shower door needs to be installed prior to proceeding with the following Stationary and Return Glass installation instructions Please see the Single Shower Door installation manual included in the door packaging for complete shower door installation instructions Before you begin the installation please recheck your shower opening size Specific size information can be found using the SKU TO GLASS SIZE GUIDE below and on our website at www BathAuthority com NOTE The installation of this enclosure requires two installers NOTE Use parts from Detailed Diagram of Glass l Panel Components for the glass panel assembly and BX ae installation SS 1 Please locate and record the SKU numbers found on the packaging of both glass panels and door You will specifically need all Product Width values to calculate your Shower Enclosure size SKU TO GLASS SIZE GUIDE Product Width Product Height ss ee Be we eeseeeeeeeeeeeeeeee se ise eeeeee ee seeeee i sss8es8e8e8e8888 8288888 _ ce e828 Product Line Glass Model Product Thickness Glas
11. h a generous strip of Painters tape See Fig 8 amp 9 for details A i SY 7 Fig 7 outside 2 inside inside Return glass 4 pe Stationary Return glass glass outside SS inside outside Xx Stationary glass l 6 Painters tape ie qi cr N 5 cide outside a Fig 8 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 NOTE The next step involves careful handling of the glass panels that were just temporarily fixed together to determine a custom fit measurement unique to your installation It is essential that two installers be used along with responsive communication 8 Carefully butt the Return panel glass 26 up against the wall vertically according to the M value stated in Size Table A on page 5 Intermittently use a level throughout these steps to ensure that this glass enclosure is leveled properly While securely holding the glass panels close the Glass Door and align the Stationary glass 11 to it Use the door mark on the threshold as a reference to ensure that the Door is perpendicular to the wall If needed adjust the position of the Stationary glass and Return panel glass so that the Anti Water strip inline panel 19 makes tight contact to the Glass Door from top to bottom The U channel 1 wall profile 09 will remain flush against the wall Outline the position of the glass pa
12. l residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THI
13. nels along the inside bottom edge of all U channels on the threshold and wall Mark the U channel 1 wall profile 09 at the top horizontal glass edge See Fig 10 for details ee LE VA L Fig 9 outside fl 1 ney A 2 NY inside outside an HL ty 3 4 Stationary glass Door D 7 1 16 1 8 Z Z Align stationary glass R and glass door inside oe inside SS 5 6 i U channel 1 wall ie a inside inside a UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 9 Carefully disassemble the panels for the 90 Corner next steps Bracket See Fig 11 for details SY U channel 1 V Anti Water strip Return glass Stationary glass mT ANN ZA NU channel 2 U channel 2 oS Qo aN Painters tape Fig 11 10 Place the U Channel 2 bottom profile 29 for the Return panel glass 26 onto the threshold base in line with the inside threshold mark Mark the drill holes on the threshold through the predrilled holes in the U Channel 2 and drill the holes using 1 8 drill bit Apply waterproof silicone along the bottom surface and around the holes of the U Channel 2 and fasten it to the base with the Countersunk screws ST4 2 X 40 23 waterproof silicone NOTE The surface needs to be clean and free of debris
14. omer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 If this unit is going to be installed in new construction please install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation 4 Prior to the installation please ensure that the installation surface is level and solid and will be able to support the total weight of the unit Also make sure that the walls are plumb Depending on the type of unit you are installing some adjustments in leveling may be possible However irregular installation surface level or out of square conditions can result in serious problems for your installation Please note that some adjustments and drilling may be necessary Please protect all primary surfaces of the product during installation Never set your glass down directly onto a tile floor Always use a piece of wood or cardboard to protect the
15. on or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISC
16. reamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modificati
17. rproof silicone _ waterproof silicone inside Fig 27 ERF inside Fig 28 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 18 19 Notch the Anti Water strip inline panel 4 9 19 1 at the base to fit around bottom inside U channel Press the Anti Water strip onto the vertical edge of the Stationary aide glass 11 See Fig 29 for details 3 4 neige inside outside outside Fig 29 Maintenance To ensure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To ensure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to pre
18. s Type SHEN Shower Enclosure 10mm No Code Clear SHDR Shower amp Tub Door FR Frosted HFR Frosted Band SHDR GL2402 227210 HFR Unidoor Plus Shower Door Glass Panel 22 x 72 x 10mm Half Frosted Band UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 2 Please mark measurement lines on the wall and threshold for the Glass Door and U channel according to the size of your model You will need use the Product Width values determined in step 1 in Size Table A NOTE M and L dimensions are from the finished wall to the outside of the U channel as shown in Fig 1 M Door Panel 1 8 L Return Panel 7 16 Size Table A NOTE The Unidoor hinge is designed to over close 8 The following procedure is recommended to ensure proper alignment of the panel glass and door 3 Align the Door so that it is perpendicular to the wall and parallel to the threshold Measure across the bottom span of the Door and threshold on the outside of shower and determine an equal value Mark a line on the threshold base on the handle side See Fig 2 for details Panel J X gt s A ZY gt Z Vv Fig 1 1 Door j inside outside BSS yar gt inside outside Fig 2 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 4 Measure the actual width of your Return panel glass 26
19. urn panel glass aside SS Cut the U channel 2 bottom profile 45 to the mark 1 2 The end facing the wall will remain Sy J straight T iil Slip the U channel 2 bottom profile back onto the inside Return panel glass and set the Return panel glass aside Fig See Fig 5 for details Ss 6 Measure the actual width of your Stationary glass 11 panel L Use a miter saw to cut the second U channel 2 40 bottom profile 29 45 to the actual width of the glass 1 16 See Fig 6 amp 7 for details as Fig 6 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 7 Slip the U channel 2 40 bottom profile 29 onto the Stationary glass 11 and ensure that the straight end of the U channel 2 is flush with the vertical glass edge Press the Anti Water strip inline panel 19 onto the vertical edge of the Stationary glass allowing the base of the strip to rest on top of the U channel Carefully butt the Stationary glass and Return panel glass 26 together to form a tight corner from bottom to top The Stationary glass will be in front of the Return panel glass While securely holding the two glass panels attach the 90 Corner Bracket 30 to the top corner Ensure that the 90 Corner Bracket is square and gaskets are aligned properly before tightening the glass holding screws Temporarily secure the bottom corner of the glass panels wit
20. vent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 Style T Half Etched Glass Installation NOTE This model features the half etched glass option Hinged Left installation shown To install for hinged Right flip the door to the proper handing The textured surface of the return panel glass stationary glass and glass door should face out See Fig 30 for details Fig 30 UNIDOOR PLUS STYLE I Rev 1 Ver 1 06 2014 20 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED
Download Pdf Manuals
Related Search