Design House 545798 Instructions / Assembly
Contents
1. SHOWER HEAD INSTALLATION 4 Insert shower arm through wall 4 4 4 hole and thread to appropriate line Q Thread shower head onto shower arm REMEMBER TO WRAP THREADED CONNECTIONS WITH TEFLON TAPE OR JOINT COMPOUND EXPLODED DIAGRAM M Oo Ns Color button way 2 Cover Plaster Washer Escutch scutcheon 05 ay Gasket 06 Trim sleeve 07 Nut 13 Sing 14 Cartridge Valve stem 15 z O ring O ring 16 z F Shower arm Spring ody Spool 18 f Washer oe oe Diversion valve MAINTENANCE Your new Design House faucet is designed to give you years of trouble free performance Keep it looking new by cleaning it periodically with a soft cloth Avoid abrasive cleaners steel wool and harsh chemicals as these will dull the finish and void your warranty Brass finishes are polished then protected with a lacquer coating to help prevent tarnishing Clean these surfaces only with a damp soft cloth CONSUMER PROTECTION WARNING Under the Safe Drinking Water Act the U S Environmental Protection Agency restricts the amount of lead used in brass and solder Your new faucet is made in strict compliance with all government standards The materials used in the manufacture of this faucet are of industry standard quality and are similar to other plumbing products having brass fittings To reduce the amount of lead in your drinking water allow the water to run for a moment before2. Design House is a registered brand of DHI Corp Mequon WI 53092 Caley o DESIGNHOUSE 1 800 558 8700 MIDDLETON SINGLE as HANDLE SHOWER FAUCET Models 545806 545780 545798 Your new Design House faucet will give you years of trouble free performance Thank you for choosing our product for your home Please read all of these instructions carefully before installing your new faucet Helpful tools to install this faucet P ag Zs S gt K Se Adjustable Wrench Teflon Tape Silicone Sealant Pipe Wrench Screwdriver IMPORTANT POINTS Wrap threaded connections except where o ring or rubber sealant are present with Teflon tape available from your local hardware or plumbing supply store Always wrap in a clockwise direction SAFETY TIPS ALWAYS protect your eyes with safety glasses INSTALLATION PROCEDURE CONTD 5 To remove the plaster guard loosen and remove the 2 screws Pull the guard straight out to remove Discard before installing escutcheon Trim sleeve will remain in place 5a Place handle on valve stem and turn handle to full on mixed position Turn on hot and cold water lines to full open for one minute each Check for leakage Shut off water at faucet Remove the Handle REMARK Adjust the water temperature by adjusting the rotational limit Remove the red rotational limit stop from the valve by sliding it off the stem Rotate counter clockwise to increase temperature or clock
3. filling your glass and remember to always use cold water for drinking purposes
4. wise to reduce temperature Re install in correct position 6 With gasket in place slide escutcheon over trim sleeve Fasten escutcheon to faucet body and tighten to finished wall surface using two mounting screws HANDLE INSTALLATION T 7 Slide handle onto as shaft 8 8 Insert screw through handle and thread to faucet body Insert button sti set screw COMPLETED INSTALLATION INSTALLATION PROCEDURE 1 Shut off main water supply Preparation Assembly of recommended component locations Valve depth should be front of valve to front of the finished wall of approx 2 3 16 1 7 8 2 1 2 max Shower and or spout outlet hole should be 1 1 4 diameter and Valve access hole should be 6 diameter Caution Allow at least 2 between the tub outlet and tub rim 2 Connect water supply lines using 1 2 threaded pipes and 90 degree elbows Wrap all threaded connections with Teflon tape or joint compound Note water limit screw stops are preset at the factory if they are present on valve Modification is not required 2 2 PLUG 2 WRAP WITH TUB TEFLON TAPE ONLY N TUB RA 2 N SHOWER AND SHOWER HOT f Pipe should stick outside HOT Pipe should stick outside HOT finished wall by 4 t finished wall by 4 j 3 Plaster guard is preinstalled The front surface of the plaster guard should sit flush with the finished surface of the wall
Download Pdf Manuals
Related Search