American Standard 1340.225.002 Installation Guide
Contents
1. Installation Inst ti METERING 1340 225 Center Set Faucets 1340 255 1340 265 Thank you for selecting American Standard the benchmark of fine quality for over 100 years 1340 265 To ensure that your installation proceeds smoothly please read these instructions carefully Certified to comply with ANSI A112 18 1 before you begin i M968493 Recommended Tools Tubing Cutter Channel Locks Adjustable Wrench Plumbers Putty or Caulking 2 5mm Hex Wrench g israr FAUCET P MAKE WATER SUPPLY CONNECTIONS CAUTION NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS MUST BE x cake PURCHASED SEPARATELY Turn off hot and cold water supplies before beginning m Connect water supply to FAUCET 1 with 1 2 IPS FLEXIBLE m Apply a bead of PUTTY along the edge of the SUPPLIES 1 or 3 8 0 D BULL NOSE RISERS 2 underside of the FAUCET 1 Use adjustable wrench to tighten connections Do not over m ech a eee through holes of SINK or tighten Be careful not to kik copper supply when bending Use tubing cutter to cut to proper length E Install GASKET 2 FRICTION WASHER 3 DEEP WASHER 4 and LOCK NUT 5 onto SHANKS 6 E Tighten LOCK NUTS 5 firmly to secure FAUCET 1 FERRULE 3 TEST INSTALLED FITTING Turn on water supplies and check connections for leaks E Remove AERATOR 1 with KEY 2 supplied Operate HOT and COLD HANDLES by pressing down on HANDLES Both Hot and Cold handles are set fo2. emove SPOUT 2 Remove SPOUT CLIP 8 and O RINGS 4 Replace RUBBER RING 5 with separate PLASTIC RING 6 supplied with faucet Replace SPOUT CLIP 3 and O RINGS 4 Reassemble SPOUT 2 TO BODY REMOVE RUBBER RING wsta 6 PLASTIC RING M968493
3. r approximately 8 second operating cycles Replace AERATOR 1 BONA io OPERATE Remove HANDLE 1 by removing INDEX BUTTON 2 and SET SCREW 8 with a 2 5mm hex wrench Pull off HANDLE 1 To increase cycle time turn the gray PLASTIC ADJUSTING NUT 4 clockwise To decrease cycle time turn the gray PLASTIC ADJUSTING NUT 4 counter clockwise Replace SET SCREW 3 INDEX BUTTON 2 and HANDLE 1 Test faucet for proper operation and cycle time t i a e T 2 5mm HEX WRENCH TO DECREASE CYCLE TIME ROTATE COUNTER CLOCKWISE TO INCREASE CYCLE TIME ae CLOCKWISE CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE Remove HANDLE 1 Refer to Step 4 for handle removal Remove ACTUATOR ASSEMBLY 2 Remove WASHER 3 Pull out VALVE ASSEMBLY 4 and FILTER SCREEN 5 Inspect that VALVE ASSEMBLY 4 FILTER SCREEN 5 and VALVE SEAT 6 are clean and free from debris VALVE ASSEMBLY 8 and FILTER SCREEN 5 can be cleaned with soap and water Hee FILTER SCREEN 5 and VALVE ASSEMBLY 4 Place WASHER 3 on top of VALVE ASSEMBLY 4 Thread VALVE ACTUATOR 2 onto faucet Torque VALVE ACTUATOR 2 to 12 15 ft Ibs 15 20 Nm Replace HANDLE 1 CONVERT RIGID SPOUT TO SWIVEL SPOUT 1340 255 1340 265 Unthread SPOUT NUT 1 and r
Download Pdf Manuals
Related Search