Speakman SB-1421 Installation Guide
Contents
1. Instructions for Models SB 1421 SB 1421 BN SB 1421 PN Need Help For additional assistance or service call SPEAKMAN Company 400 Anchor Mill Road New Castle DE 19720 PHONE 800 537 2107 EMAIL customerservice speakmancompany com WEB www speakmancompany com 92 3325 R What You Need To Know Tools Required rench Bevo eta Teflon Tape Helpful Supply Lines her Utility Knife Groove Joint Phillips Pliers Screwdriver Basin Wrench Eye Protection What You Need To Know Important Notes Be sure to read instructions thoroughly before beginning installation Do not overtighten any connections or damage may occur This faucet has an operating range of 20 80 psi Safety Tips Cover your drain to prevent loss of parts Be sure to wear eye protection while cutting pipe Maintenance Your new Lavatory Faucet is designed for years of trouble free performance Keep it looking new by cleaning it periodically with a soft cloth Avoid abrasive cleaners steel wool and harsh chemicals as these will dull the finish and void your warranty Shut off water supplies Remove old faucet Clean sink surface in preparation for new faucet Place spout thru mounting hole in sink Secure spout with rubber washer metal washer and nut Slide Hot and Cold end valves thru sink mounting holes Make sure long tubes are installed facing away from spout Note Hot side end valve is labeled Secure end2. ontal rod 2 Insert rod through hole in lift rod strap 3 Secure with spring clip 1 Insert lift rod 1 into strap 2 and tighten screw 3 IMPORTANT D After installation is completed remove aerator Turn on water supply and allow both hot and cold water to run for at least one minute each While water is running check for leaks Replace aerator a D 14 11 1 RPGO4 0401 PC BN PN 2 RPGO5 0889 HOT VALVE 3 RPGO5 0890 COLD VALVE 4 RPG45 0046 5 RPG63 0084 6 RPG05 0892 PC BN PN 7 RPG24 0127 PC BN PN 3 39 86 19mm 1 25 31 70mm 358 46mm 8 00 203 20mm 6 27 159 31mm 6 11 155 29mm 103 89mm 2 36 60 00mm 2 36 60 00mm
3. valves with washers and nuts Hand tighten nuts onto shank Lock nuts into position by tightening screws Align tabs 1 and 2 on quick connects 3 Push quick connect housing firmly upward and snap onto receiving tube tab Pull down moderately to ensure connection has been made If it is necessary to remove quick connect squeeze tabs on hose between index finger and thumb then pull down to disconnect Make connections to water lines Use 1 2 IPS faucet connections 1 or use the supplied coupling nuts 3 with 3 8 O D ball nose risers 2 Use wrenches to tighten connections Do not overtighten ORS 2ed SOS SRR eM aS Ko OOOO K D aie ve 1 KX K Remove flange 1 and rubber washer 2 from pop up drain assembly the provided gasket or plumber s putty to the underside of the flange 3 Insert the threaded end of the drain body up through the drain hole and attach flange to the body with the pivot 4 pointing to the rear of the sink 6 Add Teflon Tape 1 to the drain body 2 Apply D Unscrew the nut 1 from the pop up body Note retain the seal 2 on the horizontal rod 3 Place the nut onto the horizontal rod and insert the rod and seal 2 into the pivot hole 4 Install stopper 5 as non removable 6 Slide nut 1 on and hand tighten only 8 Tighten nut 1 clockwise until the pop up drain assembly is secure Place one end of spring clip 1 on the end of horiz
Download Pdf Manuals
Related Search