American Standard 2506.101.002 Installation Guide
Contents
1. Replace the YYY with appropriate finish code CHROME 002 STAINLESS STEEL 075 HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1 2 00 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008 M968941 Rev 1 22. it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A Fig B f Fig C STOPPER S Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A STOPPER REMOVAL PROCEDURE Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F REMOVE CAM CAP M968941 Rev 1 2 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked M
3. Amtrican Standard Installation Instructions MOMENTS 2506 101 Monoblock Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Certified to comply with ANSI A112 18 1 Speed Connect Drain M968941 Rev 1 2 e Fewer parts installs in less time e Never needs adjustment e Guaranteed to seal properly the first time every time Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools e O Screwdriver Channel Locks Adjustable Wrench INSTALL FAUCET MAU is before beginning Seat SEAL 1 into under side of FAUCET BASE 2 Feed FAUCET SUPPLIES 3 MOUNTING STUD 4 and DRAIN CABLE ASSEMBLY 8 through the mounting hole of lavatory or mounting surface Fig A From below push GASKET 7 and RETAINING WASHER 5 onto MOUNTING STUD 4 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink so SUPPLIES 3 rests against mounting hole Before final tightening make sure collar on Ne NUT 6 is seated into RETAINING WASHER 5 ig B Adjust Faucet so that it is centered Tighten MOUNTING NUT 6 to complete faucet mounting MOUNTING SURFACE COLLAR ON MOUNTING NUT 2 POP UP DRAIN E Remove C
4. LEAR PLASTIC COVER 1 E Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 m Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B J A F 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM z BELOW FIXTURE _ m From under side of SINK OF SINK Tighten LOCKNUT 1 firmly with Adjustable Wrench or Channel Locks install DRAIN BODY 1 up through drain outlet Note No plumber s putty ea BRAIN or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Le 1 Z E Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly 6 FLANGE GASKET AND POP UP KNOB m Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A WHITE FOAM m POP UP KNOB 1 must be fully down Fig B GASKET DRAIN NOT VISIBLE FLANGE N EA M968941 Rev 1 2 7 ATTACH CABLE CONNECTOR E Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 0 D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify tha
5. n rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing or outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968941 Rev 1 2 Americam Standard MOMENTS Momoblock Lavatory Faucet M962558 YYYOA HANDLE wa s M962559 0070A BUTTON AND Ta A906099 0070A S o SCREW KIT HANDLE ADAPTER H 2 5mm HEX KEY m962561 YYYOA CARTRIDGE COVER G M923320 YYYOA CARTRIDGE NUT Cc gt A912740 0070A O RING 951970 0070A CARTRIDGE m M961619 0070A MANIFOLD M952425 YYYOA DRAIN ASSEMBLY M962560 YYYOA POP UP ROD Ea M922881 YYYOA AERATOR A911836 0070A SEAL EA i Z M919660 0020A MOUNTING ar haat 6 TAILPIECE NOT INCLUDED M918462 0070A gt AEE CABLE ADAPTER with Pop up Drain MODEL NUMBERS m M962544 YYYOA STOPPER ASSEMBLY M952430 0070A CABLE ASSEMBLY t M962457 YYYOA FLANGE ASSEMBLY M922872 0070A CAM SEAT INSERT A M962552 0070A f ret CAM ASSEMBLY MA M913207 0070A TAILPIECE INSERT A919661 0020A TAILPIECE m M962458 0070A DRAIN MOUNTING KIT
6. ode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD REAR OF SINK Re install the Cam Cap making sure the guide teeth are facing or outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drai
7. t STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS E Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left SUPPLY 1 to Hot Marked with a Red Band and right supply to COLD 2 wall supply Faucet supplies are 20 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are to long loop as illustrated to avoid kinking Connect 1 1 4 Q D tailpiece on POP UP DRAIN to n waste outlet OX 20 BLUE BAND 3 8 COMPRESSION M968941 Rev 1 2 1 0 TEST INSTALLED FITTING With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate HANDLE 1 to flush water lines thoroughly Replace AERATOR 3 CHECK DRAIN CONNECTIONS Operate POP UP KNOB 4 and fill lavatory with water Check that DRAIN STOPPER 5 makes a good seal and retains water in SINK If DRAIN STOPPER 5 does not seal properly please refer to Troubleshooting section in these instructions Release POP UP KNOB 4 down and check all drain connections and P trap for leaks Tighten if necessary SERVICE E Turn on valve and allow water supply temperatures to s
8. tabilize Move HANDLE to full HOT setting Check water temperature E To decrease hot limit temperature setting Pull out Plug Button 1 loosen Handle Set Screw 2 and remove Handle 3 from Cartridge Stem 5 Remove Cartridge Cover 4 Lift Setting Insert 6 rotate counterclockwise one notch and replace Check water temperature and repeat if necessary Unit is factory set at O full HOT water As the setting number increases the more cold water is supplied in the full HOT handle position Replace Cartridge Cover 4 Align Handle 3 and tighten Set Screw 2 Replace Plug Button 1 1 2 CARE INSTRUCTIONS CARTRIDGE a ON S an AS amp Q HOTTEST Q Blend control setting O setting insert covers blend control setting number 1 4 COOLEST Blend control setting 4 DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968941 Rev 1 2 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly ollow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting
Download Pdf Manuals
Related Search