American Standard 2555.901.002 Installation Guide
Contents
1. onto VALVE STEMS 8 Figure B With colored side up place FRICTION RING 6 over DECK ADAPTER 10 Loosely screw FRICTION NUT 5 onto DECK ADAPTER 10 Do not tighten Align flats on FRICTION NUT 5 with RIBS 9 in HANDLE BASE 4 Figure C Screw HANDLE BASE 4 with FRICTION NUT 5 onto DECK ADAPTER 10 until snug against mounting surface and aligned properly Figure D Install LEVER HANDLE 3 onto HANDLE ADAPTER 7 and align Check alignment if not satisfactory remove and align Insert HANDLE SCREW 2 and tighten Press in INDEX BUTTON 1 4 Figure B 2 3 M968788 Rev 1 2 Drop SPRAY ESCUTCHEON 1 through the fourth hole of the tub ledge 12 max from SPOUT center with SPRAY ESCUTCHEON 1 directed towards tub center Be sure RUBBER RING 2 is properly seated in ESCUTCHEON 1 Install RUBBER WASHER 3 BRASS WASHER 4 and LOCKNUT from underside of ledge Secure SPRAY ESCUTCHEON 1 by tightening LOCKNUT Add SEAL WASHER 5 and connect HOSE 10 to outlet nipple at the bottom of COUPLING 7 Tighten firmly Slip SHOWER HOSE 8 with COUPLING NUT through SPRAY ESCUTCHEON 1 Install SEAL 9 and connect both HOSES 8 and 10 Connect HAND SHOWER 11 to SPRAY HOSE 8 Leu When not in use HANDSHOWER should be seated in the HOLDER 6 TEST INSTALLED FAUCET The flow rate of this Tub Filler exceeds 20 gallons minute Turn VALVES off and attach handles at higher w2. 6 POLISH ABRASIVES HARSH Reinstall ESCUTCHEON 4 and HANDLE CLEANERS OR A CLOTH WITH ASSEMBLY A COARSE SURFACE If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1200 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008 M968788 Rev 1 2
3. Installation TOWNSGUARE Instructions DECK MOUNT BATH FILLER 2555 900 2555 901 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please Certified to comply with ANSI A112 18 1M read these instructions carefully before you begin ee Rev i Required Tools ROUGHING IN DIMENSIONS Z 3 8 1 4 gt Phillips Screwdriver ADJ 6 1 2 TO 12 S MOUNTING SURFACE C Flat Blade Screwdriver a ar taa1 2 Max ON 4 F l 1 3716 D ep i Wrench H ene Supplied bg ANEMIA a60 SPOUT ASSEMBLY CAUTION Prepare TUBE and TEE ASSEMBLY 1 to fit center to center Turn off hot and cold water supplies before beginning VALVE 2 location between 6 1 2 and12 If necessary cut and or bend TUBING carefully Make sure tube bend is close to the TEE 1 so that it will not effect the compression E Insert SPOUT SHANK 1 through center hole of MOUNTING LEDGE joint at the VALVE CONNECTION Make sure that the RUBBER RING 2 is properly seated in RECESS at base o
4. ater pressure Do not fill bathtub unattended With handles in off position turn on water supplies and check E Lift HANDSHOWER from HOLDER direct spray into tub lift ell Coniceions fal bake TRANSFER KNOB to check HANDSHOWER and HOSES for leaks Operate both handles and flush water lines thoroughly Check SPOUT mounting for leaks E Turn handles off F Before the bathroom is completely finished you may want to remove spout handshower and handles E To remove handles reverse steps in section 4 E To remove SPOUT 1 proceed as follows 3 4 Lift TRANSFER ROD 2 and unscrew KNOB 3 Model 2555 90only Remove PLUG BUTTON 4 and remove SET SCREW 5 using 5mm hex wrench supplied Lift SPOUT 1 off SHANK 6 carefully and remove RUBBER RING 7 Unscrew SHANK SLEEVE 8 and lift TRANSFER ROD 2 from SHANK 6 Model 2555 901 only m Reverse sequence to re install SPOUT 1 Be sure RUBBER RING 7 is properly seated in its recess at the base of the SPOUT 1 Make certain SET SCREW 5 is properly aligned and tight so that SPOUT 1 is locked in place 9 CARE INSTRUCTIONS a a EE DO SIMPLY RINSE THE PRODUCT j Tura Vavett IFF pasah CLEAN WITH CLEAR WATER DRY a Pull out INDEX CAP 1 and remove WITH A SOFT COTTON FLANNEL HANDLE SCREW 2 CLOTH Pull off HANDLE 3 and unscrew ESCUTCHEON BASE 4 DO NOT DO NOT CLEAN THE eee PRODUCT WITH SOAPS ACID I turn ana replace Replace SPRING CLIP
5. f SPOUT 3 Remove COUPLING NUT 3 and FERRULE 4 from each Assemble RUBBER WASHER 4 and BRASS WASHER 5 onto VALVE 2 and slide onto TUBING 5 SHANK 1 From underside of ledge secure SPOUT 3 into position with LOCKNUT 6 MOUNTING LEDGE VALVE inlet is 3 4 inch NPT male connector 3 VALVE ASSEMBLY Install LOCKNUTS 1 and RUBBER WASHERS 3 onto valve shanks AO DECK ADAPTER Push TUBING 4 ends into VALVE 5 side outlets Insert VALVES 5 7 into mounting holes from underside of ledge Press TEE 6 onto SPOUT SHANK 7 making certain that the O RING 8 is properly seated on SHANK 7 Push COUPLING 9 or 9a into TEE 6 and attach to SPOUT SHANK 7 and tighten Note For product with Hand Shower COUPLING 9 is tightened using a 710mm 3 8 Hex Wrench Place RUBBER RING 11 into DECK ADAPTERS 10 and thread onto valves until snug against internal stop E Tighten LOCKNUT 1 to secure VALVE 5 position E Slide FERRULE 13 and COUPLING NUT 14 to outlet of VALVE 5 and tighten COUPLING NUT 14 firmly Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector _ S MOUNTING SURFACE 5 16 MIN 1 5 D es FOR FITTING 9 amp 9 LESS SPRAY INSTALL HANDLES Turn VALVE to OFF position Figure A Install STEM ADAPTERS 7
Download Pdf Manuals
Related Search