American Standard 7010.900.002 Installation Guide
Contents
1. 1 proceed as follows a Unthread LIFT ROD KNOB 2 to release it from the TRANSFER ROD 8 Remove LIFT ROD KNOB 2 VIEW A Remove PLUG BUTTON 3 and remove SET SCREW 4 using 4mm hex wrench supplied Lift SPOUT 41 off SHANK 5 carefully and remove RUBBER re VIEW A RING 6 a5 Heppa Unthread SHANK SLEEVE 7 and remove from SHANK 5 Reverse sequence to re install SPOUT 1 Be sure RUBBER RING 6 is properly seated in its recess at the base of the SPOUT 1 Make certain SET SCREW 4 is properly aligned and tight so that SPOUT 1 is locked in place CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968595 Rev 1 32. by tightening LOCKNUT 4 Add SEAL WASHER 5 and connect HOSE 10 to outlet nipple at the bottom of TEE 7 Tighten firmly Slip SHOWER HOSE 8 with COUPLING NUT through SPRAY HOLDER 6 and ESCUTCHEON 1 Note SPRAY HOLDER 6 must be separate from ESCUTCHEON 1 to get HOSE 8 thrrough ESCUTCHEON 1 Install SEAL 9 and connect both HOSES 8 and 10 INSTALL second SEAL 9 and connect HAND SHOWER 11 to SPRAY HOSE 8 NOTE When not in use HANDSHOWER should be seated in the HOLDER T7 MAKE WATER SUPPLY CONNECTIONS Connect HOT water supply to LEFT INLET UNION 1 and COLD water supply to eo RIGHT INLET UNION 2 Pipe connections are 3 4 NPT Use sealant or Teflon tape on pipe connections Do not solder directly to valve body 7 A TEST INSTALLED FAUCET E With HANDLES in OFF position turn on WATER SUPPLIES and check all connections for leaks mb Operate both HANDLES to flush water lines thoroughly 3 4 X 3 4 NPT UNION NOT SUPPLIED Lift HAND SHOWER from HOLDER direct spray into tub Lift TRANSFER KNOB to check HAND SHOWER and HOSES for leaks m IMPORTANT It is strongly recommended that access be provided for all enclosed mechanical parts to this system Turn handles off and replace HAND SHOWER Before the bathroom is completely finished you may want to remove spout handshower and handles to avoid damage during construction To remove handles reverse steps in section 4 To remove SPOUT
3. Installation Instructions GREEN TEA 7010 900 DECK MOUNT BATH FILLER 7010 901 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended Tools ROUGHING IN DIMENSIONS 3 Flat Blade Screwdriver pie 10 5 8 j 5 Ie BEDS 3 MOUNTING 3 3 4 Wrench SURFACE Adjustable Wrench _ 2 9 16 1 1 8 DIA v aoa eo Channel Locks Hex key Supplied with Fitting j SPOUT ASSEMBLY f ADJ 6 1 2 TO 12 gt j Certified to comply with ANSI A112 18 1M M968595 Rev 1 3 7 7 8 200mm t 1 3 16 DIA rey ale 1er off hot and cold water Prepare TUBE and TEE ASSEMBLY 1 to fit center to center supplies before beginning VALVE 2 location between 6 1 2 and 12 If necessary E Install RING WASHER 1 into SPOUT recess Check that O RING 2 cut and or bend TUBING carefully Make sure tube bend is on end of SPOUT SHANK 3 is in place Insert SPOUT SHANK 3 close to the TEE 1 so that it wi
4. NTING SURFACE E FOR FITTING LESS SPRAY 5 16 MIN 1 4 i il INSTALL HANDLES m Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up Fig A Tighten STEM SCREW 3 to secure ADAPTER 1 Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Push LEVER HANDLE ASSEMBLY 4 down onto ADAPTER 1 Thread base of LEVER HANDLE ASSEMBLY 4a onto DECK ADAPTER 5 until snug against mounting surface SPLINE END DOW 5 SERVICE To change direction of handle Turn valve to OFF position Thread HANDLE BASE 11a counter clockwise until loose Pull HANDLE 1 UP firmly to release from ADAPTER 2 Remove SPRING CLIP 3 Lift STOP WASHER 4 turn 90 and replace Replace SPRING CLIP 3 Re install HANDLE ASSEMBLY 1 If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 M968595 Rev 1 3 HANDSHOWER INSTALLATION FOR MODEL 7010 901 ONLY Drop SPRAY ESCUTCHEON 1 through the fourth hole of the tub ledge 12 max from SPOUT center with SPRAY ESCUTCHEON 1 directed towards tub center Be sure RUBBER RING 2 is properly seated in ESCUTCHEON 1 Install RUBBER WASHER 8 and LOCKNUT 4 from underside of ledge Secure SPRAY ESCUTCHEON 1
5. ll not effect the compression through center hole on mounting surface joint at the VALVE CONNECTION Remove COUPLING NUT 3 and FERRULE 4 from each Assemble RUBBER WASHER 4 and BRASS WASHER 5 and VALVE 2 and slide onto TUBING 5 LOCKNUT 6 onto SPOUT SHANK 3 Align SPOUT ASSEMBLY and from underside of ledge secure SPOUT ASSEMBLY into position with LOCKNUT 6 SPOUT ASSEMBLY MOUNTING SURFACE MOUNTING SURFACE VALVE inlet is 3 4 inch NPT male 3 VALVE ASSEMBLY Install LOCKNUTS 1 and RUBBER WASHERS 2 onto valve shanks 11 MOUNTING SURFACE Push TUBING 3 ends into VALVE 4 side outlets Insert VALVES 4 into mounting holes from underside of ledge Press TEE 5 onto SPOUT SHANK 6 making certain that the O RING 7 is properly seated on SHANK 6 Push COUPLING 8 or 8a into TEE 5 and attach to SPOUT SHANK 6 and tighten For 7005 901 use a 10 mm 3 8 hex key Thread of VALVE BODY 4 should extend at least 5 16 inch above MOUNTING SURFACE 11 If necessary adjust LOCKNUT 1 Place RUBBER RING 10 into ESCUTCHEON ADAPTERS 9 and thread onto valves until snug against internal stop Tighten LOCKNUT 1 to secure VALVE 4 position Slide FERRULE 1712 and COUPLING NUT 13 to outlet of VALVE 4 and tighten COUPLING NUT 13 firmly Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector al 8 141 MOU
Download Pdf Manuals
Related Search