DreamLine DL-6997-01CL Installation Guide
Contents
1. DREAMLINE ream in style Charisma Tub Door amp QWALL TUB Kit Tub Door AND SHOWER BACKWALLS KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page UN tn STEP 1 Install Shower Backwalls ower Backwalls Installation Instructions STEP 2 Install Shower Door ower Door Installation Instructions Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Kit please visit www BathAuthority com lt BREAMLINE dream in style CHARISMA SHOWER TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read2. handheld jig saw See Fig 11 and Fig 12 for details Fig 11 wet Fig 12 Rev 1 1 9 Mount the Center cover 05 to the center of the back wall using the Countersunk screws ST4 2x30 07 Do not tighten the screws Leave the Center cover loose on the wall See Fig 13 for details 10 Apply the sealant to the back of the left Back panel 02 See Fig 14 for details Fig 13 Fig 14 Rev 1 1 11 Slide the right edge of the left Back panel 02 all the way behind the Center cover 05 and push the Back panel against the wall You can adjust the position of the Back panel before the sealant sets Apply equal pressure to the whole surface of the Back panel from top to bottom Fasten the Corner cover 04 to the left corner of the back wall using the Countersunk screws ST4 2x30 07 Do not tighten the screws See Fig 15 for details 12 Repeat Step 10 and Step 11 to install the right Back panel 02 to the right side of the back wall See Fig 16 for details S 2 Fig 15 4 9 q i 6 Fig 16 Rev 1 1 13 Align both Back panels at the top and tighten the screws on the Center cover
3. 05 to secure this assembly in place See Fig 17 and Fig 18 for details Fig 17 Fig 18 Rev 1 1 14 Determine the position of both Side panels 01 NOTE a Narrow side of the Side panel cannot be trimmed and should face the corner of the side wall Wide side of the Side panel can be trimmed to size of your measurements and should face the front of the tub b Place a mark on the wide side of the Side panel with a distance of D 1 from the corner side of the Side panel to the front edge and draw a straight line from top to bottom See Fig 19 for details 1 uo Place the Side panel 01 on a flat piece of plywood or a particle board Cut the side end of the Side panel by making a few deep scratches with a sharp industrial knife using a T Square tool or a handheld jig saw See Fig 20 and Fig 21 for details Fig 19 Rev 1 1 16 Dat Place the marks on the Side panel 01 which is going to the side wall with the fixtures according to the taken measurements in Fig 4 Drill the holes in the Side panel Mind using the proper diameter saw bit or a handheld jig saw See Fig 22 and Fig 23 for details pia
4. Ver 2 Rev 1 10 Bring the Guide rail 01 over 1 4 the top of the Guide rail brackets 11 and lock them together Mark the drill holes in the R Guide rail through the hole in the middle of the bracket drill the holes using 1 8 drill bit Slide the Roller assemblies 10 into the f channel of the Guide rail io W Two rollers in each slot Remove the Guide rail and 2 5 NOTE Pay attention to the direction of the Roller assemblies LEE A They all need to face the LEE L Ss same direction as shown _in i Figure 10 images 5 6 i a Place the Guide rail back into position and fasten the Guide rail to the Guide rail bracket with Fig 11 the Round head screw ST4 2x10 17 See Fig 11 and Fig 12 for details Fig 12 Ver 2 Rev 1 11 Secure the Glass doors 03 onto the Roller assemblies 10 and fasten them with the E provided bolts be Attach the Handle brackets 12 onto the Glass 7 gi doors J Attach Handles 04 to the Handle brackets 1 4 See Fig 13 and Fig 14 for details ot P 2 5 of 3 6 Fig 13 NOTICE On the outside Glass door the Handle must be installed outwards On the inside Glass door the Handle must be installed inwards Fig 14
5. clean nonabrasive cloth If desired a mild nonabrasive detergent may also be used Use only light pressure when cleaning Avoid rubbing dirt or grit into the surface Turn the cloth often and replace with a clean cloth frequently Dry by blotting gently with a clean dry cloth DO NOT USE Window cleaning sprays alcohol kitchen abrasive compounds or solvents such as acetone gasoline or thinners Do not use ammonia based cleaning solutions on the acrylic as it will eat into the surface and cause it to damage How do you get scratches out of Acrylic For light scratches use a buffing compound such as a car wax Use the buffer or slightly buff the surface by hands until scratches disappear Rev 1 1 22 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine p
6. these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Doors and Tub Doors please visit www BathAuthority com Ver 2 Rev 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Tub Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 Prior to the installation please insure that the surface is level and
7. Fig 21 Fig 22 Rev 1 1 17 Apply the sealant to the back surface of the Side panel 01 Apply the sealant around the drilled holes and to the whole back side of the Side panel See Fig 24 for details Fig 23 Fig 24 Rev 1 1 18 Slide the edge of the Side panel 01 all the way behind the Corner cover 04 and push the Side panel against the wall Align the top of the Side panel with the Back panel before the sealant sets Apply equal pressure to the whole surface of the Side panel from top to bottom Peel off the adhesive tape on the back side of the Decorative edge molding 03 and attach it to the front edge of the Side panel Apply pressure to the Decorative edge molding from top to bottom See Fig 25 for details NOTICE If you are installing a shower door with the wall profile you can hide the edge of the Side panel 01 behind the wall profile See Fig 26 for details Fig 25 Wall Profile gt Side Wall Dn Panel Wall Side Panel Profile Fig 26 Rev 1 1 19 Apply the sealant to the back surface of the Side panel 01 for another side wall instal
8. OR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authori
9. Ver 2 Rev 1 10 12 Slide the Glass doors 03 to the right side and secure the Left Guide block 13 to the left end of the Threshold 02 Drill the holes into the Threshold through predrilled holes in the Guide block and fasten the Guide Block with the Round AY head screw ST4 2x16 06 Slide the Middle Guide block 13 off the left edge of the Glass doors and secure it to the center of the Threshold Drill the holes into the Threshold using 1 8 drill bit and fasten the Guide block to it using Round head screw ST4 2x16 06 2 4 Now slide the two doors to the left side and 1 8 install the Right Guide block 13 to the right end of the Threshold Cover the screws with the Decorative af covers for Guide block 09 _ See Fig 15 1 Fig 15 2 and Fig 15 3 for details NOTICE To align the doors you need to adjustment the bolts on the rollers Fig 15 13 Press the Bumper strips 14 on the vertical edges of the Glass doors 03 See Fig 15 4 for details 14 Apply sealant along the connection of the Guide rail 01 and the Shower base See Fig 16 and Fig 17 for details Caulk Fig 16 Ver 2 Rev 1 11 Caulk Fig 17 Product Maintenance To ensure long lasting life for your acrylic back walls wipe them off after each use with a soft
10. X f dimension X from the back wall from Step 4 Even front bottom corner of the Guide Rail Bracket with the outside of the j Threshold 02 to mark the wall for drilling Be sure to keep the Guide Rail Bracket 1 level X 69 1 4 See Fig 7 for details Fig 7 Height of the Guide Rail Bracket for Tub door 7 Place your Guide Rail Bracket 11 at a xX height of 55 3 16 from the base and at dimension X from the back wall from Step 4 P Even front bottom corner of the Guide f i Rail Bracket with the outside of the Threshold 02 to mark the wall for drilling Be sure to keep the Guide Rail Bracket 55 3 16 level X See Fig 8 for details Fig 8 Ver 2 Rev 1 8 Mark the drill holes on the wall using the Guide rail bracket 11 Drill the holes using 5 16 drill bit insert the Wall anchors 05 and secure the Guide rail bracket to the wall with the Round head screw ST4 2 x35 08 See Fig 9 for details 9 Repeat Step 6 Step 7 and Step 8 to mount the second Guide rail bracket 11 to the opposite wall See Fig 10 for details Note The Guide Rail 01 must be installed eve and parallel to the Threshold 02 to ensure proper operation the unit i 4 Si 3 5 3 25 16 i Fig 9 1 4 Fal 2 5 KL ek 3 25 16 Fig 10
11. amLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR F
12. cidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such as a photo may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com EAMLINE dream in style TEL 866 731 8378 215 957 1411 FAX 866 227 9245 215 893 1780 WWW BATHAUTHORITY COM For more information on DreamLine Tub Back Wall please visit www BathAuthority com Rev 1 1 24
13. cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To ensure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To ensure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes Ver 2 Rev 1 12 QREAMLINE ream In style QWALL TUB TUB ACRYLIC BACK WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com w
14. dware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement Rev 1 1 Back Panel Installation Instruction 1 Measure the distance of the back wall of the tub corner to corner W The distance is W See Fig 1 for details Fig 1 W 2 2 Divide the W measurement by 2 S W 2 Place a mark on the back wall e W 2 and draw a vertical line from top to bottom See Fig 2 for details Fig 2 Rev 1 1 3 Measure the side walls from the corner to the front point where the Side panel 01 is going to end This distance is D See Fig 3 for details 4 Verify on which side of your tub wall the fixtures will be installed Place a mark on the side wall NB not the side panel with a distance of 1 one inch from the corner and draw a vertical line from top to bottom Take the exact measurements e from the fixture to the line A B C e from the fixture to the bottom E F See Fig 4 and Fig 5 for details Fig 3 1 D 1 E F lan AN l WY Na F L B C ry D Fig 4 Rev 1 1 5 Attach the Center cover 05 vertically at the center point along the line and mark the drilling holes through the predrilled holes on the Center cover Drill the holes using 5 16 d
15. ead screw ST4 2x35 4pcs 17 Round head screw ST4 2x10 2pcs 09 Decorative cover for Guide block 6pcs NOTE Carefully unpack your unit and inspect it Lay it out and identify all of the parts using the detailed diagram above and packing list in your manual as a reference Before discarding the carton check for any small hardware bags that may have fallen to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Ver 2 Rev 1 Shower Tub Door Installation 1 Measure your finished opening width This distance is marked as W See Fig 1 for details Fig 1 2 The Guide rail 01 and the Threshold 02 have been precut for an opening width of 60 If your finished opening width is less W N p than 60 you will need to cut the Guide A Nef rail and the Threshold to the size of Bi You can use a chop saw if available or a hack saw File down any burrs that occur to prevent scratches on the wall i NOTE The Guide Rail and Threshold PS must be cut to the same length This unit does not allow for out of plumb lt wall conditions See Fig 2 and Fig 3 for details Ver 2 Rev 1 3 If the Threshold 02 has been cut off the pre drilled hole may be shifted In this case you will need to drill another hole Drill the hole fro
16. eb page A Please carefully read the instructions before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at 1 866 731 8378 ext 3 or e mail our technical support group at support BathAuthority com For more information on DreamLine Tub Back Wall please visit www BathAuthority com Rev 1 1 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Tub Back Wall Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 3 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 3 business days or if the product has been installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project 3 This acrylic wall sys
17. for details an Tub Glass Shelves Installation Instruction Fig 31 25 Mark the location for the Shelf brackets 10 according to the measurements in Fig 32 1 Drill the holes using 5 16 drill bit and insert the Wall anchors 06 See Fig 32 for details G 3 o 3 avr Pe 1 IS 5 16 D 2 3 Fig 32 Rev 1 1 20 10 Mount the Glass brackets 10 to the wall using the Countersunk screws ST4 2 x30 NOTE padded set screw of the Glass bracket should be facing down Slide the upper Glass shelf 09 into the Glass brackets and tighten the set screws at the bottom of the brackets Then slide the bottom Glass shelf in place Tighten the set screws as well See Fig 33 and Fig 34 for details Fig 34 Rev 1 1 21 Product maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface Acrylic cleaning procedure Acrylic should be cleaned with warm water and a
18. lation See Fig 27 for details 20 Repeat Step 18 to install the second Side panel See Fig 28 and Fig 29 for details Fig 27 1 3 2 4 Fig 28 Rev 1 1 21 Fasten tight the Corner covers 04 and the Center cover 05 to secure the Side panels 01 and the Back panels 02 in place See Fig 28 for details Fig 29 Fig 28 Rev 1 1 22 23 Use decorative plugs to cover the screw holes in the Corner covers 04 and the Center cover 05 See Fig 29 for details Apply caulk along the top edge of the panels and along the connection of the bottom edges of the panels with the tub See Fig 30 for details ATTENTION Installation of QWALL Tub is complete If you want to install Glass shelves 09 to your Tub Wall follow to the next step Fig 29 Fig 30 Rev 1 1 24 Find the desirable height for the Glass shelves 09 and mark the locations on the wall NOTE The Glass shelves can be installed either two in one corner or one in each See Fig 31
19. m the top 1 1 2 away from the end of the Threshold Drill through both layers of aluminum using 03 16 drill bit and then enlarge the hole of the first layer with 5 16 drill bit See Fig 4 for details A Fig 3 j 1 A I i LULLED i AMM J l g g A I 1 1 2 3 16 7 z2 2 ZE E PORE 3 4 5 16 Ver 2 Rev 1 4 Place the Threshold 02 in the desired position and parallel to the front edge of the Shower base or the Tub Measure the distance from the front edge of the Threshold to the far corner of the wall This distance is X you will need this distance for Step 6 Mark the drill holes through the predrilled holes at both ends of the Threshold See Fig 5 for details Drill the holes in the Shower base or the Tub using 1 8 drill bit Apply a layer of caulk or silicone to the bottom side of the Threshold 02 and secure it to the Shower base with the Round head screw ST4 2x25 07 Cover the screw holes with the Decorative covers for Threshold 15 See Fig 6 for details Fig 5 1 8 1 8 Fig 6 Ver 2 Rev 1 Height of the Guide Rail Bracket for Shower door 6 Place your Guide Rail Bracket 11 at a J height of 69 1 4 from the base and at
20. ot limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a Dre
21. rill bit and insert the Wall Anchors 06 See Fig 6 and Fig 7 for details Fig 5 5 16 Ne A Fig 6 Rev 1 1 6 Attach the Corner cover 04 to the corner of the wall and mark the drilling holes through the predrilled holes on the Corner cover Drill the holes using 05 16 drill bit and insert the Wall Anchors 06 See Fig 8 and Fig 9 for details Fig 7 O5 16 Fig 8 Rev 1 1 Fig 9 7 Determine the position of both Back panels 02 O wo NOTE EOS a Narrow side of the Back panel 5S cannot be trimmed and should face the center of the Back wall b Wide side of the Back panel can be trimmed to the size of the wall X a and should face the corner W241 Place a mark on the wide side of the Back panel with a distance of W 2 1 from the center edge of the Back panel to the wide side of the Back panel and draw a straight line from top to bottom See Fig 10 for details Fig 10 Rev 1 1 8 Place the Back panel 02 on a flat piece of plywood or a particle board Cut the side end of the Back panel by making a few deep scratches with a sharp industrial knife using a T Square tool or a
22. roduct by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but n
23. solid and will be able to support the total weight of the unit Also make sure that the walls are plumb Please note that some adjustments cutting and drilling might be necessary during the installation process Please protect all primary surfaces of the product during installation 4 Never set your glass down directly onto a tile floor Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass 5 Please NOTE This door does not have out of plumb adjustment Make sure your walls are plumb and your sill is level and that your finished opening width is between 56 and 60 Tools Required Caulk Tape Pencil Phillips Drill bit Drill bit Drill bit Measure Screwdriver 5 16 3 16 1 38 NE Om SSS Wh Level auk Pleng Hammer Miter saw or Hacksaw Ver 2 Rev 1 2 Detailed Diagram of Shower Tub Door Components 5 zeg pn T Pirmi o puntin Vo sA IN 16 17 pim Packing List 01 Guide rail lpc 10 Roller assembly Apcs 02 Threshold lpc 11 Guide rail bracket 2pcs 03 Glass door 2pcs 12 Handle bracket Apcs 04 Handle 2pcs 13 Guide block left right middle 1set 05 Wall anchor 4pcs 14 Bumper strips Apcs 06 Round head screw ST4 2x16 6pcs 15 Decorative cover for Threshold 2pcs 07 Round head screw ST4 2x25 2pcs 16 4mm hex wrench 1pc 08 Round h
24. tem is specially designed to be installed over any solid surface If you are installing the acrylic walls over the existing tiles remove all loose tiles before the installation If you are installing over the existing painted walls take all loose paint off Please note that some cutting and drilling might be necessary during the installation process 4 Make sure to turn off the water supply remove faucet handles or any fixture trims protruding from the wall Clean the surface removing soap film and dirt from all wall surfaces using regular household detergent then wipe it dry Tools Required Tape Drill bit T Square Caulk Measure Pencil Knife 5 16 S D Caulk l Phillips Level Gun ee l Hammer Screwdriver Rev 1 1 2 Detailed Diagram of Tub Back Wall Components 4 1 1 2 3 5 6 3 i i 9 10 Packing List 01 Side panel 2pcs 06 Wall anchor 21pcs 02 Back panel 2pcs 07 Countersunk screw ST4 2x30 21pcs 03 Decorative edge molding 2pcs 08 Decorative cover 15pcs 04 Corner cover 2pcs 09 Glass shelf 2pcs 05 Wall cover 1pc 10 Shelf bracket 6pcs NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small har
25. zed dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special in
Download Pdf Manuals
Related Search